Instrukcja obsługi JETI J-MSW-100-MS

JETI Zabawki sterowane radiem J-MSW-100-MS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JETI J-MSW-100-MS (8 stron) w kategorii Zabawki sterowane radiem. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
U
SER
M
ANUAL
ELECTRONIC
SWITCH
Main Switch
By JETI model s.r.o 25. 9. 2014
User Manual: Electronic switch Main Switch
-2-
1. Introduction
Main Switch is an electronic switch designed primarily for switching of the main power supply for an RC model. It adds
an element of safety when handling the model, without the need to physically disconnect the model´s batteries. A big
advantage of electronic switches in comparison to mechanical switches is, in general, their higher reliability as far as
vibration resistance is concerned. Another advantage of the electronic switch is its ability to withstand an unlimited number
of switching cycles. Electronic switches have no moving parts like contacts which would be worn out during the switching
processes, therefore their longevity is extremely high. Moreover, they are not prone to spontaneous and unexpected false
tripping with known disastrous effects. Last but not least, electronic switches offer a much lower inherent transient
resistance in comparison to mechanical switches. The Main Switch prevents the connectors from sparking when
connecting the batteries, thus it can also replace Anti Spark plugs.
The Main Switch is shipped with a magnetic switch. The magnetic switch instructions can be found on the
manufacturer´s website. It is also possible to use the optional RC Switch instead of the magnetic switch.
The Main Switch is primarily designed for switching the main power supply of the RC models, but can also be used in
applications where switching a DC power supply is needed.
2. Connection
The power supply is connected to the Main Switch using two input wires with cross sections of 6 or 8mm
2. The output
voltage is available at two cables with cross sections of 6 or 8mm2. The output three-wire cable with the JR connector is
used for telemetry data transmission. The output three-pin connector is used to connect the supplied magnetic switch or
the RC Switch.
The Main Switch connects and disconnects the negative pole - , the + pole is always connected and is never
disconnected!
Fig. 1: Connection of input and output cables
Be sure to connect the power supply wires correctly; always connect the red cable to the + pole of the
accumulator, the black cable to the – pole of the accumulator. Pay attention when connecting outputs and inputs,
they must not be swapped. Failure to follow these requirements may result in irreversible damage to the Main
Switch!! Only connect batteries to the input IN and connect speed controllers, receivers, servos etc. to the output
OUT.
User Manual: Electronic switch Main Switch
-3-
Before switching on the electronic switch you should always connect the batteries first and only afterwards
switch on the system using the magnetic switch or the RC Switch. Follow this rule also for the switching off
procedure. Switch the system off first and disconnect the batteries only afterwards.
2.1 Connection of the Main Switch
The Main Switch measures the battery current and the voltage. If you do not need to get telemetry information from the
Main Switch, you do not have to connect the Ext. output. If you DO want to display then the telemetry the Main Switch Ext.
output must be connected to the Ext. Duplex receiver input. This also powers the measurement part of the Main Switch.
Fig. 2: Block diagram of the Main Switch
The ground (-) of the Main Switch Ext. is isolated. Do not connect the ground (-) of Magnetic switch / RC Switch to the
output ground of the Main Switch (-OUT).
2.2 Charging of the battery
The battery can be charged while connected to the Main Switch (be sure that the Main Switch is in the off state – the
green LED is off), but do not attempt to disconnect the battery while charging. The charging voltage is to be connected
directly to the battery (alternatively, to the battery through the switch input), but never connect charging voltage to the
switch output!! If it becomes necessary to disconnect the battery, disconnect the charging voltage first!! Failure to follow
these basic rules can destroy the Main Switch!!

Specyfikacje produktu

Marka: JETI
Kategoria: Zabawki sterowane radiem
Model: J-MSW-100-MS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JETI J-MSW-100-MS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zabawki sterowane radiem JETI

JETI

JETI TD1609S Instrukcja

23 Września 2024
JETI

JETI JDEX-RR7 Instrukcja

23 Września 2024
JETI

JETI JEX-MF2G-800 Instrukcja

22 Września 2024
JETI

JETI Central Box 220 Instrukcja

22 Września 2024
JETI

JETI MEZON 75 opto (RPM) Instrukcja

22 Września 2024
JETI

JETI Central Box 210 Instrukcja

22 Września 2024
JETI

JETI Duplex Rsat 2 EX Instrukcja

22 Września 2024
JETI

JETI JM-090-L Instrukcja

22 Września 2024
JETI

JETI TD0905L Instrukcja

22 Września 2024
JETI

JETI AddCAP 1640 Instrukcja

22 Września 2024

Instrukcje Zabawki sterowane radiem

Najnowsze instrukcje dla Zabawki sterowane radiem

Spektrum

Spektrum AR6600T Instrukcja

15 Października 2024
Amewi

Amewi Hyper Go Instrukcja

9 Października 2024
Carson

Carson Drift Burner Instrukcja

9 Października 2024
Carson

Carson Micro X-Warrior 2.0 Instrukcja

9 Października 2024
Hobbywing

Hobbywing XeRun XR10 Pro WP Instrukcja

9 Października 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec G2 Instrukcja

9 Października 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3S Instrukcja

9 Października 2024
Hobbywing

Hobbywing XeRun XR8 PRO G3 Instrukcja

9 Października 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3 Handout Instrukcja

9 Października 2024
Hobbywing

Hobbywing XeRun XR8 Plus G2S Instrukcja

9 Października 2024