Instrukcja obsługi JETI Hicopter 90A opto

JETI Zabawki sterowane radiem Hicopter 90A opto

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JETI Hicopter 90A opto (1 stron) w kategorii Zabawki sterowane radiem. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
HiCOPTER
The HiCOPTER product line of speed controllers are designed for controlling and regulating
brushless motors that are typically used for powering multicopters. Each speed controller is pre-set
from the factory with settings optimized for use with multi rotor aircraft stabilization systems.
HiCOPTER controllers accept a control signal with a frequency of up to 500Hz. This allows them to
accurately respond to any RPM change required by the control/stabilization unit of the multicopter.
The motor control signal is galvanically (optically) separated from the flight battery in all
HiCOPTER speed controllers. HiCOPTER speed controllers do not require or allow any programming
changes. The propeller brakes are already switched off, the cut-off voltage is pre-set to the lowest
possible level (depending on type) and the motor timing is set automatically by the speed controller. If
you need to change the direction of rotation, simply swap any two of the motor wires.
Install the HiCOPTER speed controller in accordance with the manual instructions for your specific
multicopter type.
Basic parameters of HiCOPTER speed controllers
Type Current
[A]
Input voltage
[V]
Dimensions
[mm]
Weight*
[g]
HiCOPTER 30A opto 30 5-25,2 65x26x9 35
HiCOPTER 40A opto 40 5-25,2 65x26x9 38
HiCOPTER 70A opto 70 5-25,2 70x26x11 45
HiCOPTER 90A opto 90 12-42 65x55x17 100
* weight with the cables
General Principles:
•please read these instructions carefully
•use only new connectors of good quality, which must be soldered properly to the controller
cables (look out for and remove any remaining flux on the plugs)
•flight battery wires can be extended to a maximum overall length of 20 cm
pay attention to the distance between all cables and the receiver antenna – the two should be
kept as far apart as possible
•only connect the flight batteries to the flight system shortly before the flight and then
disconnect them immediately after landing
•when the model is not in use, always disconnect all batteries from the flight system
•to prevent the possibility of reverse polarity connections to the controller or batteries use
different types of connectors for each type of connection
•do not connect the controller to current supplies other than appropriate battery pack (verify
that your batteries are the correct input voltage and can handle the current load)
•to prevent possible injuries by moving mechanical parts of the model (motor, gear box etc.)
always keep in mind that the motor may start unintentionally
•check the controller and receiver circuitry each time before switching the system on
•install the controllers in the model so that they receive air flow for cooling
Warranty:
We grant a warranty of 24 months from the date of purchase under the premise that the item has
been operated in accordance with these instructions within the specified voltage and currents and that
the controller does not show signs of mechanical damage. The warranty is void if the polarity of the
controller has been reversed or if the controller came in contact with different chemicals or water.
A controller can also be damaged due to following reasons: Use of unsuitable connectors, low
quality soldering joints (plugs), overly long cables between battery – controller – motor, a
demagnetizated motor, phase interruption (broken or damaged wire) between motor and controller
during operation.
Warranty service and any post warranty service is provided by the distributor or manufacturer.
JETI model s.r.o., Lomená 1530, 742 58 Příbor, Czech Republic www.jetimodel.cz

Specyfikacje produktu

Marka: JETI
Kategoria: Zabawki sterowane radiem
Model: Hicopter 90A opto

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JETI Hicopter 90A opto, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zabawki sterowane radiem JETI

JETI

JETI TD1609S Instrukcja

23 Września 2024
JETI

JETI JDEX-RR7 Instrukcja

23 Września 2024
JETI

JETI JEX-MF2G-800 Instrukcja

22 Września 2024
JETI

JETI Central Box 220 Instrukcja

22 Września 2024
JETI

JETI MEZON 75 opto (RPM) Instrukcja

22 Września 2024
JETI

JETI Central Box 210 Instrukcja

22 Września 2024
JETI

JETI Duplex Rsat 2 EX Instrukcja

22 Września 2024
JETI

JETI JM-090-L Instrukcja

22 Września 2024
JETI

JETI TD0905L Instrukcja

22 Września 2024
JETI

JETI AddCAP 1640 Instrukcja

22 Września 2024

Instrukcje Zabawki sterowane radiem

Najnowsze instrukcje dla Zabawki sterowane radiem

Spektrum

Spektrum S6245 Instrukcja

25 Lutego 2025
Futaba

Futaba R7214SB Instrukcja

5 Lutego 2025
Futaba

Futaba GY470 Instrukcja

5 Lutego 2025
Futaba

Futaba GYA553 Instrukcja

5 Lutego 2025
Futaba

Futaba SBS-01RO Instrukcja

15 Stycznia 2025
Spektrum

Spektrum DX5 Pro Instrukcja

29 Grudnia 2024
Sharper Image

Sharper Image Space Blaster Shooting Game Instrukcja

18 Grudnia 2024
Axial

Axial Wraith Spawn Instrukcja

15 Grudnia 2024
Spektrum

Spektrum AR6600T Instrukcja

15 Października 2024
Amewi

Amewi Hyper Go Instrukcja

9 Października 2024