Instrukcja obsługi JennAir JJW2830LL

JennAir piekarnik JJW2830LL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JennAir JJW2830LL (76 stron) w kategorii piekarnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/76
FOR SERVICE TECHNICIAN’S USE ONLY
Tech Manual Do not remove or destroy
W11324895A 08/20
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
DANGER
Electrical Shock Hazard
Only authorized technicians should
perform diagnostic voltage measurements.
After performing voltage measurements,
disconnect power before servicing.
Failure to follow these instructions can
result in death or electrical shock.
Voltage Measurement Safety Information
When performing live voltage measurements, you must do the following:
■ Verify the controls are in the off position so that the appliance does not start when energized.
■ Allow enough space to perform the voltage measurements without obstructions.
■ Keep other people a safe distance away from the appliance to prevent potential injury.
■ Always use the proper testing equipment.
■ After voltage measurements, always disconnect power before servicing.
FOR SERVICE TECHNICIAN’S USE ONLY
2
IMPORTANT: Electrostatic Discharge (ESD) Sensitive Electronics
ESD problems are present erywhere ESD may damage or weaken the electronic control assemblyev . . The new control
assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.
■ Use an antistatic wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the
appliance
-OR-
Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance.
■ Before removing the part from its package, touch the antistatic bag to a green ground connection point or
unpainted metal in the appliance.
■ Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.
■ When repackaging failed electronic control assembly in antistatic bag, observe above instructions.
3
Diagnostics
Unplug oven or disconnect power before performing the following checks:
■A potential cause of a control not functioning is corrosion on connections.
Observe connections andcheck for continuity with an ohmmeter.
■All tests/checks should be made with a VOM or DVM having a sensitivity
of 20,000 Ω per volt DC or greater.
■Check all connections before replacing components, looking for broken
or loose wires, failed terminals, or wires not pressed into connectors far
enough. Damaged harness must be entirely replaced. Do not rework a
harness.
■Resistance checks must be made with power cord unplugged from outlet
and with wiring harness or connectors disconnected.
■If the oven does not heat, there may be a problem with connections to
the power supply. Check the connection to L2.
IMPORTANT: Do not replace the control if there is no evidence of any failure.
To Enter Diagnostics Mode:
Before proceeding with any corrective action, perform the following steps to
enter the Diagnostics mode:
1. Enter Diagnostics mode by pressing the same 3 keypads 3 times in a row.
Single Ovens: Press KITCHEN TIMER>TOOLS> SELF CLEAN (repeat 2
more times).
Double Ovens: Press UPPER OVEN>LOWER OVEN>LOWER LIGHT
(repeat 2 more times).
NOTE: You do not need to wait for any audible or visual feedback from the
control between keypad presses.
2. If control does not enter Diagnostics mode, continue repeating the keypad
sequence from Step 1. All the keypads will light up when the control enters
Diagnostics mode.
3. From the Diagnostics menu, scroll to the desired selection using the
touch screen.
Error Diagnostics: View and clear the failure history.
Component Activation: Manually activate each relay.
Sensors & Switches: View the traditional oven cavity temperatures and
door/latch switch status.
System Information: View the model number, serial number, and
software versions.
Exit Diagnostics
General Procedure: Error Codes
NOTE: All failures are stored in the failure history. To check if the error code
is still present, start a cooking function and wait 1 minute to check if the error
appears.
1. Enter Diagnostics mode.
2. Touch or scroll to “Error Diagnostics” in the Diagnostics menu, and then
touch “OK.”
3. To clear error codes, touch “Clear History.”
4. If no failures are listed, the message “No Error” willappear on the screen.
General Procedure: Software Version
For Engineering only

Specyfikacje produktu

Marka: JennAir
Kategoria: piekarnik
Model: JJW2830LL

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JennAir JJW2830LL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje piekarnik JennAir

JennAir

JennAir JIS1450ML Instrukcja

26 Września 2024
JennAir

JennAir JDS1750EB Instrukcja

22 Września 2024
JennAir

JennAir JED4430KS Instrukcja

21 Września 2024
JennAir

JennAir JDRP436HL Instrukcja

21 Września 2024
JennAir

JennAir WOS31ES0JS Instrukcja

21 Września 2024
JennAir

JennAir KOSE500EBS Instrukcja

18 Września 2024
JennAir

JennAir JDRP430HM Instrukcja

18 Września 2024
JennAir

JennAir JJW2827IL Instrukcja

17 Września 2024
JennAir

JennAir JGRP636HL Instrukcja

17 Września 2024
JennAir

JennAir JEC4430KS Instrukcja

17 Września 2024

Instrukcje piekarnik

Najnowsze instrukcje dla piekarnik

Wolf

Wolf M Series Instrukcja

15 Października 2024
Princess

Princess 112741 Instrukcja

15 Października 2024
Boretti

Boretti VFPNR 1202 IX Instrukcja

15 Października 2024
Ilve

Ilve MDC-120 Instrukcja

15 Października 2024
Frigidaire

Frigidaire FCWD2727AW Instrukcja

15 Października 2024
Fisher & Paykel

Fisher & Paykel CG302DLPGB4 Instrukcja

15 Października 2024
AEG

AEG IKK74545FB Instrukcja

15 Października 2024
Ilve

Ilve HCPT75D Instrukcja

15 Października 2024
Zanker

Zanker KOU65902XK Instrukcja

15 Października 2024
Hoover

Hoover PHC3B25CXHH64DCT Instrukcja

15 Października 2024