Instrukcja obsługi JBL Power P-2510

JBL odbiornik Power P-2510

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JBL Power P-2510 (8 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

Power Series Amplifiers

P-7520, P-7540, P-2510 Owner’s Manual

GE N UI NE JB L

Amplifier Features

• 4-, 3- or 2-channel operation (P-7540),

2- or 1-channel operation (P-7520),

mono Class-D subwoofer channel

(P-2510)

• Simultaneous stereo and mono opera-

tion (P-7520, P-7540)

• Built-in 12dB/oct variable electronic

crossover

• Balanced differential input

• Front and rear summing inputs (P-2510)

for non-fading bass

• Pre-amp outputs with crossover

(P-7520, P-7540)

• Oversized Floating Rail Mosfet Power

Supply

• Universal Interface

• Common Sense turn-on

• Variable Input Sensitivity (250mV–4V)

• Fully complementary, direct coupled

discrete power amplifier circuitry

• Ultraefficient Class-D subwoofer ampli-

fier (P-2510)

• Gold-plated power, input and output

connectors

• 2-Ohm stable (stereo)

• JBL badge lights when amp is operat-

ing and flashes when protection circuit

is activated

• Made in USA

About This Manual

To attain maximum amplifier perfor-

mance, we encourage you to read the

remaining pages before installing and

operating your new JBL Power Series

amplifier. Especially review the

Applications section for ideas on design-

ing and expanding your system. Also,

save these instructions for future refer-

ence. Installation of automo-Important:

tive stereo components can require

extensive experience in performing a

variety of electrical and mechanical pro-

cedures. Although these instructions

explain how to install a JBL Power Series

amplifier in a general sense, they do not

show the exact installation methods for

your particular vehicle. If you do not have

the experience, do not attempt the instal-

lation yourself; instead ask your

Authorized JBL Car-Audio Dealer about

professional installation options.

Installation Precautions and Notes

The JBL Power Series amplifiers have

five levels of circuit protection that moni-

tor the amplifiers and will shut them

down if the electrical-system voltage

drops below 5Vdc or exceeds 18Vdc, tem-

peratures are above 194° F (90° C), short

circuits occur or current draw exceeds

product specifications. For best perfor-

mance, check the intended mounting site

to make sure the operating environment

does not create conditions that will trig-

ger circuit protection.

• Prior to installation, turn off all audio

systems and other electrical devices.

Also disconnect the (–) negative lead

from the vehicle’s battery.

• At the installation site, locate and make

a note of all fuel lines, hydraulic brake

lines and electrical wiring. Use extreme

caution when cutting or drilling in and

around these areas.

• Check clearances on both sides of a

planned mounting surface before

drilling any holes or installing any

screws. Remember that mounting

screws can extend behind the mount-

ing surface.

Thank you for purchasing your new

JBL Power Series™ amplifier. Power

Series amplifiers feature the latest

advances in discrete-circuit topology,

ensuring low distortion and superbly

clean and clear sound quality. In addition

to RCA-type pre-amp inputs, Power

Series amplifiers feature Universal

Interface™, designed to facilitate integra-

tion with factory-installed audio systems

for distortion-free performance that rivals

conventional pre-amp connections.

Included in the Universal Interface circuit

is Common Sense™ turn-on. Common

Sense turn-on senses the common-mode

voltage present on the speaker outputs of

factory and aftermarket radios, turning on

the amplifier without a separate remote

wire. All Power Series amplifiers feature

built-in electronic crossovers and pre-

amp outputs for easy system expansion

without requiring outboard processors.

• Always wear protective eyewear when

using tools.

• When routing cables, keep input signal

cables away from power cables and

speaker wires.

• When making connections, make sure

that each connection is clean, insulated

and properly secured. Observe the

polarity markings on the rear panel.

Refer to the application drawings to set

up the amplifier for operation in stereo,

bridged-mono, bi-amp or tri-mode con-

figurations.

• If the amplifier’s fuse must be replaced,

use only the same rating and type as a

replacement. Do not substitute another

kind.

Controls and Connectors

1. Pre-amp Level Input Connector –

Connects to line-level output from the

source unit.

2. Universal Interface Speaker Level

Connector – Connects to speaker-level

output from the source unit. Provides

Common Sense amplifier turn-on

when used with factory radios

(2-channel on P-7520, 4-channel on

P-7540).

3. Pre-amp Level Output Connector –

Connects to other amps or processors

in the signal chain.

4. Speaker-Output Connector – (2-chan-

nel on P-7520, 4-channel on P-7540).

5. Fuses – P-7520: 30A ATC type, P-7540:

30A ATC type x 2, P-2510: 40A ATC

type.

6. Power Connector – Connection for

12V+, Gnd and Rem.

7. Input-Mode Switch – Sums left and

right inputs.

8. Input Sensitivity Control – Adjusts

input sensitivity for pre-amp level and

speaker-level inputs.

9. Pre-amp Output Selector Switch –

Selects input path for pre-amp output.

Output can be summed from front and

rear inputs with no filter, or filtered by

the front or rear crossover.

10. Rear-Channel Input Selector – Selects

rear-channel input between front input

and rear input.

11. Crossover Selector – Determines

whether the crossover is a High-Pass

filter (HP), Low-Pass filter (LP) or

unfiltered (flat).

12. Crossover Frequency Control –

Determines the crossover frequency

for the amplifier channels (front or

rear) and the pre-amp outputs.

FUSE

30A

BRIDG E

– R +– + L

MADE IN T HE U.S.A.

+BAT T REM GND

BRIDG E

SPEAKER OUTPUTS

POWER

FRONT

REAR

USE

30A

+R–

–L+

AUX

OUT

FRONT

REAR

LINE LEVEL

INPUT

SPKR LEVEL IN

ST O

INPUT MODE

LEVEL

INPUT

PRE OUT

LEVEL

INPUT MODE

MO ST

6V .250V 4V .250V

FRONT

F+R

FLAT

REAR

FRT

FR REAR

REAR

XOVER

FLAT HP LP

XOVER

FLAT HP LP

XOVER

AMP

XOVER

AMP

32Hz

80Hz

320Hz 32Hz

80Hz2V 2V

320Hz

7540

LINE LEVEL

INPUT SPEAKE EVEL IN

–

AUX

OUT

3 0

– R +– L + + BAT T REM G ND

FUSE

30A

MADE IN T HE U.S.A.

BRIDG E

SPEAKER OUTPUTS

POWER

PRE OUT

LEVEL

INPUT MODE

MO ST

4V .250V

XOVER

FLATPLP FLATHLP

FREQ

32Hz 320Hz

80Hz

12 8

4 6 5

711

811

4 5 6

P-7520 P-7540

Specyfikacje produktu

Marka:	JBL
Kategoria:	odbiornik
Model:	Power P-2510

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JBL Power P-2510, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odbiornik JBL

JBL Power P-2510 Instrukcja

19 Grudnia 2024

JBL Grand Touring GTS100 Instrukcja

15 Grudnia 2024

JBL Power P-4040 Instrukcja

15 Grudnia 2024

JBL Loud and Clear LCA504 Instrukcja

15 Grudnia 2024

JBL EON 15PAK Instrukcja

2 Października 2024

JBL SA550 Classic Instrukcja

28 Września 2024

JBL GT5-A3001E Instrukcja

27 Września 2024

JBL CSA 1300Z Instrukcja

16 Września 2024

JBL Stage A6004 Instrukcja

12 Września 2024

JBL Stadium 5 Instrukcja

10 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

19 Grudnia 2024

19 Grudnia 2024

19 Grudnia 2024

19 Grudnia 2024

QSC MX1000a Instrukcja

19 Grudnia 2024

QSC MX2000a Instrukcja

19 Grudnia 2024

QSC MX3000a Instrukcja

19 Grudnia 2024

QSC MX1500a Instrukcja

19 Grudnia 2024

QSC PLX1202 Instrukcja

19 Grudnia 2024

QSC PowerLight 3.8X Instrukcja

19 Grudnia 2024