Instrukcja obsługi JBL AW526

JBL głośnik AW526

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JBL AW526 (1 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
MTU-200, MT200-BK, MTU-500 & MTU-500-BK
U-Bracket Instructions
For All Weather Series Loudspeakers
Use the MTU-200 U-bracket to mount the AW266 or AW295, and MT500 U-bracket to mount the AW566, AW595 or
AW526 to walls, decks, or ceilings.
Read and follow these instructions carefully before beginning.
Installing speakers must be performed by experienced professionals. If you have any doubts about the integrity of the
structure you are mounting to or you are not sure about the proper hardware or method to use, consult a structural
engineer.
Bracket Kit Hardware Includes: (1) U-Bracket, (4) Friction Washers, (2) Bracket Washers, (2) M10 x 1.5mm x
35mm Bolts, and (2) M6 1mm x 35mm Bolts.
CAUTION:
Due to the wide variety of building structures, materials and mounting methods, these instructions assume that the
installing contractor/installer will exercise good judgment in selecting the proper mounting area and hardware.
As a guide, the installation, when complete, should be capable of supporting at least 5 times the actual load.
Step 1 – Install the Bracket Securely to Building Structure
Select the mounting area where the speaker will be positioned. Be sure there is adequate structural strength for
mounting, such as a stud. Do not rely on drywall, acoustic tiles, etc. to support the weight of the speaker. Follow
building code requirements to safely install the bracket to the building structure. Select the proper mounting hardware
for the structure and attach with at least four fasteners (two per side). If in doubt, consult a fastener specialist. Tighten
all hardware permanently.
Step 2 – Install Speaker into Bracket
Position the speaker in between the bracket arms and install the included hardware into the speaker cabinets
threaded holes. Be sure to place the friction washers between the speaker and the bracket arms and between the
bracket washer and the bracket arms then tighten the bolts loosely, not tight.
Step 3 – Wire and Aim the Speaker
Rotate the speaker until it is aimed in the desired direction and tighten the M10 mounting bolts permanently. Secure
the desired aiming angle by tightening the M6 bolts. Warning: Do not over tighten M10 and M6 bolts.
Step 4 – Safety Cable
It is strongly recommended that the speaker be secured to the mounting structure with a properly rated safety cable
attached to an M10 forged eye-bolt (not included) installed in the provided M10 attachment point located on the rear
of the enclosure.
JBL Professional, 8500 Balboa Blvd, Northridge, CA 91329
5/2012 – PN5021248


Specyfikacje produktu

Marka: JBL
Kategoria: głośnik
Model: AW526

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JBL AW526, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje głośnik JBL

JBL

JBL B-6ICDT Instrukcja

11 Stycznia 2025
JBL

JBL B-8IC Instrukcja

11 Stycznia 2025
JBL

JBL 4349 Instrukcja

11 Stycznia 2025
JBL

JBL Balboa 30 Instrukcja

31 Grudnia 2025
JBL

JBL 250Ti Instrukcja

31 Grudnia 2025
JBL

JBL 800 Instrukcja

31 Grudnia 2025
JBL

JBL 900 Instrukcja

31 Grudnia 2025

Instrukcje głośnik

Najnowsze instrukcje dla głośnik