Instrukcja obsługi Intex 28685E


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Intex 28685E (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/5
269
PO
(269PO) SOLAR HEATER MAT ENGLISH 4.875” X 7.25” 08/19/2016
SAVE THESE INSTRUCTIONS
Page 1 269-*PO-R0-1708
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
INTEX® OWNER'S MANUAL
SOLAR HEATER MAT
REF. NO. DESCRIPTION
QTY.
SPARE PART NO.
1
Solar heater mat 1 11956
2
Bypass valve 1 11954
3
Elbow joint 2 11953
4
Hose seal 5 10134
5
Hose clamp 5 11489
6
Hose 1 11955
*7
Adaptor A (For 1-1/4” hose only) 1 10849
*8
Adaptor B (For 1-1/2” hose only) 1 10722
*8
5*7
4
6
1 2
3
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
To reduce the risk of injury, do not permit children to use this product. Always supervise
children and those with disabilities.
Assembly and disassembly by adults only. This product is not a toy.
Never allow anyone to step, stand, sit or jump on this product.
Turn the pump off before installing, servicing, cleaning or adjusting this product.
Do not block the outlet of this product while the pump is running.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR
DEATH.
WARNING
269
PO
(269PO) SOLAR HEATER MAT ENGLISH 4.875” X 7.25” 08/19/2016
General
This product is for use with storable pools only. Do not use with permanently-installed
pools.
Solar heater mat size (flat, before fill): 47” X 47” (1.2 m X 1.2 m). Surface area: 11 ft
2 (1m2).
Suitable for above ground pools up to 8,000 gal (30,280 L).
Compatible with filter pump up to 1/3HP or pump flow rate less than 2,000 gal/hr
(7,570 L/hr).
Increases the pool water temperature by approximately 5-9
oF (3-5o C) depending on
weather and ambient conditions.
Setup instructions
These instructions assume that the pool and filtration system are already assembled, and
there is a pool water return (pool water inlet) hose attached.
1. Unroll and place the solar mat on the selected area where it will receive the maximum sun
exposure. See Fig 1.
2. Position the solar mat between the pool water return hose and the filter pump outlet, after
the water is filtered.
3. Place the bypass valve over the 2 openings on the solar mat. Ensure the sign “A” marked
on the elbow joint (3) matches the sign “A” on the solar mat opening. Secure the bypass
valve (2) assembly to the solar mat with hose clamps
(5). Ensure all the elbow joints and
hose clamps are securely tightened. See Fig 2.
4. Attach one end of the short hose
(6) to the remaining opening on the bypass valve
(2) and
secure the hose with a hose clamp (5). See Fig 3.
5. Before disconnecting any hoses, turn off the filtration system and close or cover all pool
inlet and outlets to prevent water from flowing out.
SAVE THESE INSTRUCTIONS
Page 2
47”(1.2 m)
1
47”(1.2 m)
2
5
5
3
6
5
Site Preparation and Requirement
Select an area that receives maximum direct sunlight for better performance. Face the
solar heater mat in the direction of the sun’s natural path.
The selected area shall be free of sharp objects, stones and debris that can puncture the
product, and away from traffic. Keep all pets away from this product.
Clear all grass and other vegetation from the selected area as grass and vegetation under
the product will die and may cause odor and slime to develop. Certain types of grass such
as St. Augustine and Bermuda, may grow through the product. Grass growing through the
product it is not a manufacture defect.
Extend the life of the product, place a tarp or mat on the ground beneath the solar heater
mat.
Do not place the product on the roof or any structure, or above the water level of the pool.
269
PO
(269PO) SOLAR HEATER MAT ENGLISH 4.875” X 7.25” 08/19/2016
Connection to 1-1/4”(32 mm) hose with clamp
1. Disconnect the pool water return hose from the pump outlet.
2. Connect the other end of the short hose
(6) to the pump outlet. Secure the hose with hose
clamps (5). See Fig 4.
3. Connect the other end of the pool water return hose to the solar heater mat outlet. Secure
the hose with hose clamp
(5) . See Fig 5. Make sure all the hose clamps are securely
tightened.
Connection to 1-1/2”(38 mm) hose with adaptor
1. Disconnect the pool water return hose from the pump outlet.
2. Connect the adaptor A
(7) to the pump outlet and attach the other end of the short hose
(6)
to the adaptor A. Secure the hose with hose clamp
(5). See Fig 6.
3. Attach the adaptor B
(8) to the solar heater mat outlet; then connect the other end of the
pool water return hose to the adaptor B
(8). Ensure the hose clamp (5) and hose nuts are
securely tightened. See Fig 7.
65
4
5
5
6
5
67
7
5
8
SAVE THESE INSTRUCTIONS
Page 3


Specyfikacje produktu

Marka: Intex
Kategoria: Niesklasyfikowane
Model: 28685E

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Intex 28685E, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Intex

Intex

Intex 58854EU Instrukcja

14 Października 2024
Intex

Intex 28002E Instrukcja

6 Października 2024
Intex

Intex 28050E Instrukcja

15 Września 2024
Intex

Intex Solar Blanket Instrukcja

10 Września 2024
Intex

Intex 58837NP Instrukcja

17 Sierpnia 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024