Instrukcja obsługi Intermatic ET2705C

Intermatic Nie skategoryzowane ET2705C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Intermatic ET2705C (6 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
Electronic 1-Circuit
7-Day Time Switch
Installation and Setup Instructions
With 100-Hour Backup
Federal Communications Commission (FCC) Notice for ET2000 Series Time Switches
Description
This document explains the setup and conguration of the Intermatic ET2705 1-Circuit
Electronic 7-Day Time Switch. The ET2705 time switch automatically switches loads
according to the entered schedule. The time switch can support up to 48 xed ON weekly
and 48 xed OFF events (96 total). Each xed event can be applied to any combination of
days.
The time switch features an LCD and panel-mounted control buttons to set, review, and
monitor the time switch functions, including setting date and time, schedule creation,
enabling or disabling Daylight Saving Time (DST) and conguring DST switchover dates.
Follow these instructions to complete the installation and programming of the ET2705 time
switch.
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause
undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and radiates radio frequency energy and, if
not installed and used in accordance with instructions, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference that requires the user to correct at his or her own expense.
MODELS ET2705C, ET2705CR, ET2705CP
Shown in indoor/outdoor
lockable metal enclosure
NOTICE
• Do NOT touch circuit board components, contact can create a static discharge, which can damage these electronic components.
• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.
• More than one circuit breaker or disconnect switch may be required to de-energize the equipment before servicing.
• For plastic enclosures, bonding between conduit connections is not automatic and must be provided as part of the installation.
• Installation and/or wiring must be in accordance with National and Local Electrical Code requirements.
• Use #14-#8 AWG wires, rated at least 105°C - COPPER conductors ONLY.
• If the power disconnect point is out of sight, lock it in the OFF position and tag it to prevent unexpected application power.
• Make sure there is no wire insulation under the terminal plate on the time switch connector. Firmly tighten terminal screws.
• For outdoor locations or wet locations (rain-tight), conduit hubs that comply with requirements of the UL514B (standard for fitting conduit and
outlet boxes) are to be used.
• Do not remove insulator that is covering terminals.
• Do NOT exceed maximum current carrying capacity.
• KEEP DOOR CLOSED AT ALL TIMES when not servicing.
Risk of Fire or Electric Shock
WARNING
Latch location Tilt top forward
Installation
Follow these instructions to install the time switch.
1. Open the time switch enclosure door.
2. Remove and retain the screw that secures the plastic insulator.
3. Lift the left side of the plastic insulator and pivot away to expose the terminal strip.
4. Press the latch at the top of the enclosure and pull out the mechanism from the
enclosure.
5. Choose and remove the selected knockout(s) from the enclosure.
NOTE: There are ve 1/2 inch to 3/4 inch combination knockouts available. There are
two on the bottom of the enclosure, one on each side, and one on the rear. If a 3/4
inch knockout is needed, remove the 1/2 inch knockout rst, then the 3/4 knockout.
6. Place the enclosure in the desired location providing space for the enclosure door to
swing open fully.
7. Securely mount enclosure using provided mounting holes.
8. Use appropriately rated ttings for the installation.
9. Snap the mechanism back into the enclosure.
10. Strip 1/2 inch off the supply and load wires. Use AWG #14-#8 copper conductors
rated at least 105ºC. Torque to 15.6 lbf-in.
11. Connect the wires to the proper terminals on the time switch and tighten the screws
rmly (See wiring diagrams).
12. Connect ground wire to grounding terminal at the bottom of metal enclosures.
13. Return the insulator to its original position and replace the screw.
14. Close enclosure door.
15. Apply power to the time switch.
Wiring Diagram
1/2 inch
AC IN
NO-1 COM1
CIRCUIT 1TIMER
POWER
L1
L2/N
OUTPUT 1
INDIVIDUAL 120/277 VAC LOADS
OUTPUT CONFIGURATION: IND
INPUT 1
AC IN
TIMER
POWER
L1
L2/N
POWER TO TIMER
120/277 VAC
(AUTO VOLTAGE, NO JUMPERS REQUIRED)
Initial Setup
The following sections provide instructions for the initial setup of the time switch.
Programming Overview
The steps to program the time switch include setting the current date, time, xed events, DST, and holiday events, setting the time
switch’s operation to AUTO mode, ENERGY SAVER mode or MANUAL mode (only MANUAL mode will appear if there are no
scheduled events) and read or write an event schedule from a USB memory stick.
NOTE: If the time switch is left inactive for ve minutes in a programming mode, it will return to the AUTO mode screen ( icon AUTO
turned on). If no scheduled events are programmed, the time switch will return to MANUAL mode. If the date has not yet been
entered, the time switch will go to the Enter Date Mode.
Setting Date
Follow this procedure below to set the date and time in the time switch.
NOTE: If necessary, hold + or - to scroll through the digits rapidly.
1. Press MODE to scroll through the mode selections until and icons appear at the top of the display. The month SET DATE
ashes.
2. Press + or - to select the current month and then press ENTER/NEXT. The day of the month ashes.
3. Press + or - to select the current day of the month, and then press ENTER/NEXT. The year ashes.
4. Press + or - to enter the current year, and press ENTER/NEXT. The month will ash again.
5. Press MODE to move to the next mode selection.
Setting Time
Follow the procedure below to set the time in the time switch.
NOTE: If necessary, hold + or - to scroll through the digits rapidly.
1. Press MODE to advance to the Set Clock mode selection if this selection is not already active. The and SET TIME icons appear
on the display and a ashing 12:00 AM appears (if clock has not been set).
2. Press + or - to select the current time. Seconds can be set to 00 by pressing ENTER/NEXT.NOTE:
3. Press MODE to save the time and move to the Enable Daylight Saving Time mode selection.
NOTE: If the time switch programming data is to be read from a USB memory stick, refer to the “Read Time Switch Program
Data…” section in these instructions.
Enable/Disable Daylight Saving Time and Setting Daylight Saving Time Rule
Congure the time switch to automatically adjust for Daylight Saving Time (DST). If DST does not apply to your region, disable the
option as directed in this procedure. Follow this procedure to enable/disable the Daylight Saving Time feature, and if applicable, set
the DST rule.
1. Press MODE to advance to the Set DST mode selection if this selection is not already active. The and SET DST icons appear on
the display.
2. Press + to display ON (enable DST) or press – to display OFF (disable DST) and then press ENTER/NEXT to save.
If DST is Then
Enabled Go to step 3.
Disabled Press MODE to save and exit. The procedure is complete.
3. Press + or - to scroll to the desired DST rules for your area.
NOTE: The DST rules are US2007 (US rules), MX1986 (Mexico rules), and CUSTOM (user-dened start/end dates).
If you select Then
US2007 or MX1986 Go to step 8. To view the start and end dates for a DST rule, press ENTER/NOTE:
NEXT to scroll through the dates and then press MODE.
Custom Press ENTER/NEXT. The screen displays a ashing and . Go to step 4.MAR 2ND
4. Press + or - to select a starting month for customized DST and press ENTER/NEXT.
5. Press + or - to select a starting week (1ST, 2ND, 3RD, 4TH, or LST) and press ENTER/NEXT.
NOTE: DST changes at 2:00 A.M. on Sunday of the user-congured starting and ending weeks. Select LST for the fth Sunday
of a month.
6. Press + or - to select an ending month and press ENTER/NEXT.
7. Press + or - to select an ending week and press ENTER/NEXT.
8. Press MODE to save the DST rules and move to the next mode selection.

Specyfikacje produktu

Marka: Intermatic
Kategoria: Nie skategoryzowane
Model: ET2705C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Intermatic ET2705C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Nie skategoryzowane Intermatic

Intermatic

Intermatic ET2705CP Instrukcja

8 Kwietnia 2025
Intermatic

Intermatic FM1D14 Instrukcja

8 Kwietnia 2025
Intermatic

Intermatic ET2715CR Instrukcja

8 Kwietnia 2025
Intermatic

Intermatic ET1725C Instrukcja

8 Kwietnia 2025
Intermatic

Intermatic ET2815CP Instrukcja

8 Kwietnia 2025
Intermatic

Intermatic ET2115CP Instrukcja

8 Kwietnia 2025
Intermatic

Intermatic ET2145C Instrukcja

7 Kwietnia 2025
Intermatic

Intermatic ET2115C Instrukcja

7 Kwietnia 2025
Intermatic

Intermatic ETW3CP Instrukcja

7 Kwietnia 2025
Intermatic

Intermatic ET2105C Instrukcja

7 Kwietnia 2025

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

Planet

Planet PWR-240-48 Instrukcja

9 Kwietnia 2025
CaterChef

CaterChef 445001 Instrukcja

9 Kwietnia 2025
Daikin

Daikin EKWCTRDI1V3 Instrukcja

9 Kwietnia 2025
Simplified MFG

Simplified MFG SP18CAT120 Instrukcja

9 Kwietnia 2025
AudioQuest

AudioQuest Pegasus Instrukcja

9 Kwietnia 2025
Reolink

Reolink P330 Instrukcja

9 Kwietnia 2025
Reolink

Reolink NVS16-8MB8 Instrukcja

9 Kwietnia 2025
Drive Medical

Drive Medical RTL12045 Instrukcja

9 Kwietnia 2025
Kern

Kern MBC-A05 Instrukcja

9 Kwietnia 2025
Daikin

Daikin EKEXVA250 Instrukcja

9 Kwietnia 2025