Instrukcja obsługi Indesit XWE 91483X K UK

Indesit Pralki XWE 91483X K UK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Indesit XWE 91483X K UK (20 stron) w kategorii Pralki. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/20

WASHING MACHINE

Instructions for use

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Disposal

Description of the washing machine, 8-9

Control panel

Display

Running a wash cycle, 10

Wash cycles and options, 11-12

Table of wash cycles

Wash options

Push & Wash

Detergents and laundry, 13-14

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 15-16

Product Guarantee and Repair Information, 17

English, 1

XWE 91483

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washing machine

is sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they

contain vital information relating to the safe

installation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its

packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4

protective screws

(used during

transportation)

and the rubber

washer with the

corresponding

spacer, located on

the rear part of the

appliance ( ).see figure

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washing machine

needs to be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls,

furniture cabinets or anything else.

2. If the floor is

not perfectly level,

compensate for

any unevenness

by tightening or

loosening the

adjustable front

feet ( ); the see figure

angle of inclination,

measured in relation

to the worktop, must

not exceed 2°.

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tap using

a ¾ gas threaded

connection (see

figure).

Before performing

the connection, allow

the water to run freely

until it is perfectly

clear.

2. Connect the

inlet hose to the

washing machine by

screwing it onto the

corresponding water

inlet of the appliance,

which is situated on

the top right-hand

side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details

table (see page 5).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Connecting the drain hose

Connect the drain

hose, without bending

it, to a draining duct or

a wall drain situated

between 65 and 100

cm from the floor;

The drain hose may

b e c on n ected t o

an under-sink trap.

Before connecting

the drain hose from

the machine ensure

that any blanks or

removable ends have

been taken off the

spigot.

If it is placed over the

edge of a basin or sink

be sure the free end of

the hose should not

be underwater.

! We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length. Ensure that if the drain

hose is pushed into a standpipe, that the end does

not go down more than 15cms (6 inches). If the hose

is pushed down too far, this may cause the machine

to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Technical

Data Plate fixed on the machine;

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

• the supply voltage is included within the values

indicated on the Technical Data Plate fixed on

the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words

on the base of the plug. Replacements can be

obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded

plug and you should wish to re-route the mains

cable through partitions, units etc., please

ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative

plug:

Important: the wires in the mains lead are

coloured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

Specyfikacje produktu

Marka:	Indesit
Kategoria:	Pralki
Model:	XWE 91483X K UK
Kolor produktu:	Czarny
Opcja regulacji wysokości:	Nie
Wbudowany wyłącznik:	Tak
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100 - 240 V
Podręcznik użytkownika:	Tak
Skala efektywności energetycznej:	Od A do G
Wbudowane głośniki:	Nie
Certyfikaty:	CE; ICES; VCCI; FCC; C-Tick; CB; TUV-GS; ISO-9241-307; cTUVus; TUV LBL; CCC; CEL; BSMI; KCC; Australia MEPS; E-standby; PSB; ISC; Microsoft WHQL Certification (Windows\n10, Windows 8.1 and Windows 7); SmartWay Transport Partnership - NA only
Maksymalne zużycie mocy:	40 W
Kraj pochodzenia:	Chiny
Typ HD:	Full HD
Typ ekranu:	TN
Długość przekątnej ekranu:	24.5 "
Rozdzielczość:	1920 x 1080 px
Współczynnik kontrastu (typowy):	1000:1
Natywne proporcje obrazu:	16:9
Ekran dotykowy:	Nie
Przewody:	AC,HDMI,DisplayPort,USB
Pobór mocy w trybie czuwania:	0.5 W
Pobór mocy:	30 W
Ilość portów HDMI:	2
Ilość DisplayPort:	1
Jasność wyświetlacza (typowa):	400 cd/m²
Technologia wyświetlacza:	LED
Kształt ekranu:	Płaski
Współczynik kontrastu (dynamiczny):	10000000:1
Maksymalna częstotliwość odświeżania:	144 Hz
Kolory wyświetlacza:	16.78 millionów kolorów
Czas odpowiedzi (typowy):	1 ms
Rozmiar plamki:	0.283 x 0.283 mm
AMD FreeSync:	Tak
Wbudowana kamera/aparat:	Nie
Pozycjonowanie na rynku:	Gaming
Kensington Lock:	Tak
Możliwośc pochylenia:	Tak
Zakres kąta nachylenia:	-5 - 23 °
Wbudowany USB hub:	Tak
Wersja USB hub:	3.2 Gen 1 (3.1 Gen 1)
Ilość portów USB Typu A downstream:	3
HDMI:	Tak
Klasa efektywności energetycznej (SDR):	F
Zużycie energii (SDR) na 1000 godzin:	23 kWh
Szerokość urządzenia (z podstawą):	569 mm
Głębokość urządzenia (z podstawą):	227.5 mm
Wysokość urządzenia (z podstawą):	407.9 mm
Waga (z podstawą):	4600 g
Szerokość (bez podstawy):	569 mm
Głębokość (bez podstawy):	62.8 mm
Wysokość (bez podstawy):	346.2 mm
Waga (bez podstawy):	3550 g
Obsługiwane rozdzielczości grafiki:	640 x 480 (VGA),720 x 400,800 x 600 (SVGA),1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 800 (WXGA),1440 x 900 (WXGA+),1600 x 900,1680 x 1050 (WSXGA+),1920 x 1080 (HD 1080)
Wbudowany tuner tv:	Nie
OSD:	Tak
Obsługa funkcji Plug & Play:	Tak
Port DVI:	Nie
Stojak dołączony:	Tak
Segment HP:	Dom
Format obrazu:	16:9
Obsługa VESA Adaptive Sync:	Tak
Wyjście audio:	Tak
Zainstalowano Thin Client:	Nie