Instrukcja obsługi Ikea NUTID HIN4T

Ikea piekarnik NUTID HIN4T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ikea NUTID HIN4T (7 stron) w kategorii piekarnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/7
11
This manual contains important information regarding
safety, the use and maintenance of your new hob. Read the
manual carefully and keep it in an easily accessible place for
future consultation.
Precautions and Advice
1. CAUTION: This cooktop complies with all
applicable safety and electromagnetic
compatibility legislation.
However, individuals fitted with a heart pacemaker
should maintain a safe distance from the appliance.
This is because it is not possible to guarantee that all
pacemakers on the market comply with the standards
in compliance with which this appliance was tested so
it is not possible to provide an absolute guarantee of
the absence of potentially harmful interference.
2. Disposal of packaging materials: The various parts of
the packing must not be sent for waste, but recycled in
conformity with the regulations imposed by local
authorities.
3. This induction hob is designed solely for use as a
domestic appliance. No other type of use is permitted.
The manufacturer declines all responsibility for
inappropriate use.
4. The appliance is not intended for use by persons
(children included) with physical, sensory or mental
impairment or without experience and knowledge of
the appliance, unless supervised or previously instructed
in its use by those responsible for their safety.
5. The cooking zones become extremely hot during use:
be careful and keep children away from the appliance
to avoid the risk of scalding or burns.
6. The letter “H” will appear on the control
panel display to indicate “residual heat” in the
corresponding cooking zone: the temperature
of the cooking zone is above 60 °C: do not
touch the cooking zone or
place any object on it while the letter “H” remains lit.
7. If the surface of the hob should become damaged
(cracked or broken glass), do not use the appliance
and call the After-sales Service immediately.
8. Any repairs or work on the appliance must be carried
out by a qualified technician.
9. This hob is equipped with a thermoprotector to
prevent the risk of its internal circuits being damaged
by high temperatures from external heat sources
(e.g. an undercounter oven). If the temperature of the
electronic circuits exceeds the safety threshold,
the thermoprotector activates, automatically
switching off the hob. The display shows an error
message (see section “Troubleshooting Guide”).
When the temperature returns to within normal levels
the hob is able to be switched on again.
10. Make sure the cooking zones and the bottoms of pots
are dry before use.
11. Do not place metal objects such as kitchen utensils
(knives, forks, spoons, etc.), lids or other similar items
on the cooking zones as they can become very hot.
12. Be extremely vigilant when cooking food with boiling
oil or fat since these can catch fire. If the oil catches
fire, never attempt to put it out with water: switch
the hob off and cover the pot immediately with a lid;
leave the pot on the cooking zone to cool down.
Dispose of the oil in compliance with current
regulations.
13. When you finish cooking, press button .
Before use
Important: The induction cooking zones
will not switch on if pots and pans are not
of the correct dimensions.
Only use pots bearing the symbol
“INDUCTION SYSTEM” (See figure
opposite).
Before switching the hob on, position the pot on the
desired cooking zone.
Existing pots and pans:
Use a magnet to check whether pots or pans are suitable
for use on the induction hob: pots are unsuitable if they
cannot be magnetically detected.
1. Ensure pots have a smooth bottom, otherwise
they may scratch the hob's glass ceramic surface.
Check dishes.
2. Do not use empty pots on the hob, especially
enamelled or aluminium ones. This could result in
damage to both the glass ceramic surface and the
bottom of the pots.
3. Never place hot pots or pans on the hob's control
panel. This could result in damage.
Recommended diameters of pot bottoms
IMPORTANT SAFETY INFORMATION
OK NO
Ø
26 cm
XL
Ø
17 cm 26 cm
Ø
21 cm
L
Ø
14 cm 21 cm
Ø
18 cm
M
Ø
14.5 cm
S
Ø
12 cm 18 cm
Ø
9 cm 14.5 cm
61901363GB.fm Page 11 Tuesday, January 1, 2002 3:20 AM
12
Installation must be carried out by a qualified electrician
who is fully aware of current safety and installation
regulations. The manufacturer declines all liability for injury
to persons or animals and for damage to property resulting
from failure to observe the regulations provided in this
chapter.
Electrical connections
•Hob electrical connection must be made before
connecting the appliance to the electricity supply.
•Electrical connection must be carried out in compliance
with the regulations of the local electric utility company.
•Make sure that the voltage indicated on the rating plate
on the underside of the appliance corresponds to the
domestic power supply voltage.
•The appliance must be earthed: use conductors
(including the earth conductor) of the appropriate
size only.
•For electrical connection, use an H05 RR-F type cable as
specified in the table “Power supply voltage”.
The power supply cable must be long enough
to allow the hob to be removed from the
worktop and must be positioned so as to avoid
damage or overheating caused by contact with
the base of the hob itself. Do not use extension leads.
Power supply voltage
If the hob already has a power cable, follow the
instructions given on the label attached to the
cable.
Connect the appliance to the electricity supply
by means of an all-pole disconnect switch with minimum
contact gap of 3 mm.
Connecting to the terminal board
Connect the yellow/green earth wire to the terminal with
the symbol . This wire must be longer than the other
wires.
1. Remove the terminal block cover (A), undoing the
screw and inserting the cover in the terminal block
hinge (B).
2. Strip approx. 70 mm of sheath from the power supply
cable.
3. Strip approx. 10 mm of sheath from the wires. Insert
the power supply cable into the cable clamp and
connect the wires to the terminal board as indicated
in the diagram next to the terminal board itself.
4. Secure the power cable with the cable clamp.
5. Close the cover (C) and screw it on the terminal block
with the removed screw - point (1).
Each time the cooktop is connected to the mains it
carries out an automatic check which lasts several
seconds.
INSTALLATION and ELECTRICAL CONNECTION
Wires Amount x size
230V ~ + 3 X 4 mm2
230-240V ~ + 3 X 4 mm2 (Australia only)
230V 3 ~ + 4 X 1.5 mm2
400V 3N ~ + 5 X 1.5 mm2
400V 2N ~ + 4 x 1.5 mm2
A
B
C
230V
230V
230V
230V
230V
230V
230V
230V
230V
230V
230V
400V 3N ~ 230V ~
230-240V~FOR AU ONLY
230V~FOR UK ONLY
400V 2N ~
230V 3~
ONLY FOR BELGIUM
400V 2N~
FOR NL ONLY
61901363GB.fm Page 12 Tuesday, January 1, 2002 3:20 AM
13
Installation and fixing
The installer is responsible for any damage or
injury resulting from incorrect installation.
To guarantee correct operation, the appliance
must be installed on a perfectly flat surface.
If necessary, cut the kitchen unit and worktop to fit before
installing the hob. Clean the cutout of any chips that could
compromise appliance operation.
Forflush mounted installation or setting into
a marble worktop, contact the After-sales
Service for the installation kit and necessary
instructions.
• 4812 310 19277 Installation kit for marble
worktop.
• 4801 211 00112 Installation kit for flush fitted
worktop.
To guarantee correct operation, the appliance must be
installed on a perfectly flat surface.
If necessary, cut the kitchen unit and worktop to fit before
installing the hob. Clean the cutout of any remaining dust
that could compromise appliance operation.
For the distance between the underside of the induction
hob and the kitchen unit (or separating panel), observe the
dimensions given in the figure at the side. If a column unit
is installed adjacent to the hob, leave a distance of at least
100 mm from the edge of the hob.
Undercounter oven installation:
•If an oven (which must be of our manufacture) is to be
installed under the hob, ensure it is equipped with a
cooling system and observe the distances given in the
figure to the side.
•There must be nothing between the hob and the oven
(cross rails, panels, brackets, etc.).
min.
5
min. 20
min. 5
5mm
61901363GB.fm Page 13 Tuesday, January 1, 2002 3:20 AM

Specyfikacje produktu

Marka: Ikea
Kategoria: piekarnik
Model: NUTID HIN4T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ikea NUTID HIN4T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje piekarnik Ikea

Ikea

Ikea TILLREDA 305.464.81 Instrukcja

7 Października 2024
Ikea

Ikea LAGAN 205.479.71 Instrukcja

6 Października 2024
Ikea

Ikea LAGAN 805.479.54 Instrukcja

6 Października 2024
Ikea

Ikea MATTRADITION 804.118.75 Instrukcja

6 Października 2024
Ikea

Ikea MATTRADITION 504.118.72 Instrukcja

6 Października 2024
Ikea

Ikea FINSMAKARE 004.118.84 Instrukcja

6 Października 2024
Ikea

Ikea ANRÄTTA 705.178.77 Instrukcja

6 Października 2024
Ikea

Ikea LAGAN 405.222.72 Instrukcja

6 Października 2024
Ikea

Ikea LAGAN 605.220.92 Instrukcja

6 Października 2024
Ikea

Ikea NYTTIG 602.906.76 Instrukcja

6 Października 2024

Instrukcje piekarnik

Najnowsze instrukcje dla piekarnik

Whirlpool

Whirlpool ACMT 5131 Instrukcja

15 Stycznia 2025
Miele

Miele H 4130 E Instrukcja

15 Stycznia 2025
Siemens

Siemens HB65AB522 Instrukcja

15 Stycznia 2025
AEG

AEG Competence 30480 B W Instrukcja

15 Stycznia 2025
AEG

AEG Competence B4100-a Instrukcja

15 Stycznia 2025
Siemens

Siemens HB78AA770 Instrukcja

15 Stycznia 2025
Indesit

Indesit FE10 K Instrukcja

15 Stycznia 2025
Siemens

Siemens he 33au540 Instrukcja

15 Stycznia 2025
Miele

Miele h 310 1 b Instrukcja

15 Stycznia 2025
Whirlpool

Whirlpool AKZ 152 Instrukcja

15 Stycznia 2025