Instrukcja obsługi IFM AC2307


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla IFM AC2307 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
Montage
Adressieren Sie den Doppelsensor T6 mit einem Adressiergerät, werks-
seitig ist die Adresse „0“ eingestellt. Befestigen Sie ihn an der Normbe-
festigung des Stellglieds (ISO 5211 VDI / VDE).
Verbinden Sie das Magnetventil mit der M12-Buchse. Es dürfen nur
Magnetventile mit 24V Nennspannung und einer Leistung bis max.
2,2W angeschlossen werden.
Belegung der Datenbits
Anschlußbelegung
Betrieb
Prüfen Sie, ob das Gerät sicher funktioniert. Anzeige durch LEDs:
LED rot leuchtet: Kurzschloder Kabelbruch in einem Ausgang.
LED gelb leuchtet: Funktionsanzeige (Ein- und Ausgangssignale wer-
den angezeigt).
Bestimmungsgemäße Verwendung
Der Doppelsensor T6 fungiert als Slave im AS-i Netz (AS-i Profil S7.F).
Er ist r den Einsatz an pneumatischen Schwenkantrieben konzipiert.
Er steuert das automatisierte Stellglied an und meldet dessen Position.
• Sensor- und Aktuatorversorgung sowie Datenübermittlung zur Steue-
ung über AS-i Zweidrahtleitung.
Watchdog-Funktion: Ist die Verbindung zum Master länger als 40ms
unterbrochen, wird der Ausgang stromlos geschaltet.
Diagnose-Informationen durch rote LED (Kurzschl oder Kabel-
bruch).
• Die Ausgänge dürfen nicht gleichzeitig gesetzt sein.
Bedien- und Funktionselemente
Montageanleitung
Installation Instructions
Notice de Montage
Doppelsensor T6
Dual sensor T6
Capteur double T6
AC2307
1 2 3 4
5
69
10
78
Datenbit Typ
Eingang
Bezeichnung
Sensor 1
Beschreibung
Sensor-Position 1 bedämpftD0
Eingang Sensor 2 Sensor-Position 2 bedämpftD1
Eingang Fehler Aktuator Kabelbruch / Kurzschluß
am Aktuator
D2
Ausgang Aktuator Schaltausgang 1
für Magnetventil
D0
Ausgang Aktuator Schaltausgang 2
für Magnetventil
D1
2
4 3
11
3 4
2
5
M12-Stecker Pin
AS-i + 1
AS-i + 3
M12-Buchse Pin
Schaltausgang 1+ 4
Spannung - 3
Schaltausgang 2 + 2
1: M12-Stecker
2: Doppelsensor T6
3: Sensorzone
4: Puck
5: Standard-Stellglied
6: Ventilstecker 1
7: Ventilstecker 2
8: Y-Kabel
9: M12-Buchse
10: AS-i Flachkabel
Sachnr. 701289/00 07/98
Functionand features
The T6 dual sensor is a slave in the AS-i system (AS-i profile S7.F).
It is designed for use on pneumatic valve actuators. It energises the
solenoid of the pneumatic valve and provides position feedback from
the actuator.
Sensor and actuator supply as well as data transfer to the controller
via AS-i 2-wire cable.
Watchdog function: If the connection to the master is interrupted for
more than 40ms, the output is switched off (logically 0) when the
master messages fail.
Diagnostic information via red LED (short circuit or open circuit).
The outputs must not be set simultaneously.
Operating and function elements
Fonctionnement et caractéristiques
Le capteur double T6 est un esclave AS-i (profil AS-i S7.F). Il est conçu
pour l utilisation sur des actionneurs de vannes. Il permet la comman-
de d une vanne et la d tection de sa position.’ é
• ’Alimentation des capteurs, de l actionneur et de l’électrovanne ai-à l
de du c ble AS-i 2 fils.â
Fonction chien-de-garde: Si la communication avec le ma tre estî
interrompue ou d faillante plus de 40ms, la sortie est dé ésactivée
(niveau logique 0).
Informations diagnostiques par LED rouge (court-circuit ou rupture
de c ble) et bit de donnâ ée.
• êLes sorties ne doivent pas tre activ es en m me temps.é ê
Eléments de service et de fonction
Montage
Adresser le capteur double T6 à l’ ’ éaide d une unit dadressage
(l adresse 0" lectionn e “ étant pré ésé à lusine). Le fixer sur la vanne
selon les normes (ISO 5211 VDI/VDE).
Raccorder l lectrovanne sur la fiche femelle M12. Uniquement pour’é
des électrovannes dune tension nominale de 24V et dune puissance
de 2,4W maxi.
Affectation des bits de données
Raccordement
Fonctionnement
Vérifier le bon fonctionnement du capteur double. Indication par LED.
LED rouge allumée: court-circuit ou rupture de câble sur la sortie.
• éLED jaune allum e: indication de fonctionnement (les signaux
dentrée et de sortie sont indiqués).
Installation
Address the T6 dual sensor with an addressing unit, address 0" is set
at the factory. Fasten it to the valve fixings according to the standards
(ISO 5211 VDI/VDE).
Connect the solenoid valve to the M12 socket. Only solenoid valves
with a nominal voltage of 24V and a power of up to max. 2.4W may
be connected.
Data bits
Connection
Operation
Check the safe functioning of the unit. Display by LEDs.
Red LED is lit: short circuit or open circuit in one output.
Yellow LED is lit: function display (input and output signals are dis-
played).
1 2 3 4
5
69
10
78
Bit de données Type
entrée
Désignation
capteur 1
Description
position 1 de la vanneD0
entrée capteur 2 position 2 de la vanneD1
entrée défaillance rupture de câble /
court-circuit sur lactionneur
D2
sortie actionneur sortie de commutation
pour électrovanne 1
D0
sortie actionneur sortie de commutation
pour électrovanne 2
D1
1: M12 fiche mâle
2: capteur double T6
3: zone active
4: came porte drapeau
5: vanne standard
6: connecteur pour électrovanne 1
7: connecteur pour électrovanne 2
8: câble en Y
9: M12 fiche femelle
10: câble plat AS-i
1 2 3 4
5
69
10
78
Data bit Type
input
Designation
sensor 1
Description
sensor position 1 dampedD0
input sensor 2 sensor position 2 dampedD1
input error actuator open circuit / short circuit
at the actuator
D2
output actuator switch output 1
for solenoid valve
D0
output actuator switch output 1
for solenoid valve
D1
2
4 3
1 1
3 4
2
5
M12 plug Pin
AS-i + 1
AS-i + 3
M12 socket Pin
switch output 1+ 4
voltage - 3
switch output 2 + 2
1: M12 plug
2: T6 dual sensor
3: sensor area
4: puck
5: standard actuator
6: valve plug 1
7: valve plug 2
8: Y cable
9: M12 socket
10: AS-i flat cable
2
4 3
11
3 4
2
5
M12 fiche mâle Pin
AS-i + 1
AS-i + 3
M12 fiche femelle Pin
sortie 1+ 4
tension - 3
sortie 2 + 2


Specyfikacje produktu

Marka: IFM
Kategoria: nieskategoryzowany
Model: AC2307

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z IFM AC2307, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany IFM

IFM

IFM RV6068 Instrukcja

4 Września 2024
IFM

IFM NN5010 Instrukcja

4 Września 2024
IFM

IFM PL1502 Instrukcja

4 Września 2024
IFM

IFM OB5025 Instrukcja

4 Września 2024
IFM

IFM PL1512 Instrukcja

4 Września 2024
IFM

IFM RB6026 Instrukcja

4 Września 2024
IFM

IFM RV6106 Instrukcja

3 Września 2024
IFM

IFM RC6045 Instrukcja

3 Września 2024
IFM

IFM RU6067 Instrukcja

3 Września 2024
IFM

IFM EVC995 Instrukcja

3 Września 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024