Instrukcja obsługi Hunter Victorian 81021

Hunter Wentylator Victorian 81021

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hunter Victorian 81021 (42 stron) w kategorii Wentylator. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/42
Bath Ventilator with Light
Owner’s Manual
Victorian
43041-01
20131201
Model
81021
English Español
Página 22
43041-01 12/01/2013
2
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
PREVEN TIVE MAINTENANCETA
A clean fan provides better service. Disconnect the power supply and clean the
fan as listed below.
TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a
soft cloth. DO NOT use abrasive cloths, steel wool pads or scouring powders.
TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove
motor plate, find the single tab on the motor plate (located next to the recepta-
cle). Push up rear motor plate tab while pushing out on the side of the housing
or insert a screwdriver into the slot in the housing (next to tab) and twist screw-
driver. Gently vacuum fan, motor and interior of housing.
METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN
WATER.
MAINTENANCE
The motor is permanently lubricated and never needs oiling. If the motor bear-
ings are making excessive or unusual
noises, replace the motor with the exact service motor. You should replace the
impeller at the same time.
1. Use this unit only in a manner intended by the manufacturer. If
you have questions, contact the manufacturer.
2. Before servicing or cleaning the unit, switch power off at ser-
vice panel and lock the service disconnecting means to prevent
power from being switched on accidentally. when the service
disconnecting means cannot be locked, securely fasten a promi-
nent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction.
4. Sufficient air is needed for proper combustion and exhausting
of gasses through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment manufac-
turer’s guideline and safety standards, such as those published
by the National Fire Prevention Association (NFPA), and the
American Society for Heating, Refrigeration and Air-Conditioning
Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall(s) or ceiling, do not
damage electrical wiring or other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must be marked as
appropriate for the application and be connected to a GFCI (Ground
Fault Circuit Interrupter) - protected branch circuit.
8. Never place a switch where it can be reached from a tub or shower.
9. Install fan at least 5 feet (1.52 m) above the floor.
10. This unit must be grounded.
11. Unit must not be installed in a ceiling thermally insulated to a value
greater than R40.
DISCONNECT ELECTRIC
POWER SUPPLY
AND LOCK OUT
SERVICE PANEL BEFORE
SERVICING UNIT
1. For general ventilating use only. Do not use to exhaust haz-
ardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy/unbalanced impel-
lers, keep drywall spray, construction dust, etc. off power
unit.
3. DO NOT install this product in a wall. This product is
designed for installation in ceilings up to a 12/12 pitch (45
degrees). Ductwork must point upward.
4. Please read specification label on product for further infor-
mation and requirements.
Do Not Install Above
Or Inside This Area
Cooking
Equipment
Floor
45° 45°
W A I N GR N
!
W A I N GR N
!
COOKING AREA
C A U NT I O
!
43041-01 12/01/2013
3
D95044-01-000
M
L
75184-01-133
97956-01-000
K65219-01-000
J77521-01-000
E95029-01-000
A
x4
F77481-01-000
G03242-07-133
I
H
74508-03-133
98037-03-000
N97958-01-000
O77537-01-199
Check all the parts.
If damaged, call
1-888-880-3267
for replacements.
Tools Needed.
Estimated assembly time: 30 to 60 minutes
Included.
B
*
C
*
3/8” Cable Connector
Extra Screws
I
x2
*
NOTE: Strain relief cable connector must be installed. Not Included.

Specyfikacje produktu

Marka: Hunter
Kategoria: Wentylator
Model: Victorian 81021

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hunter Victorian 81021, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wentylator Hunter

Hunter

Hunter Grove Park 50341 Instrukcja

8 Października 2024
Hunter

Hunter Charlotte 50402 Instrukcja

8 Października 2024
Hunter

Hunter Claudette 59622 Instrukcja

8 Października 2024
Hunter

Hunter Havoc 59470 Instrukcja

8 Października 2024
Hunter

Hunter Starklake 50409 Instrukcja

8 Października 2024
Hunter

Hunter Port Royale 50390 Instrukcja

8 Października 2024
Hunter

Hunter Midtown 54211 Instrukcja

8 Października 2024
Hunter

Hunter Donegan 53336 Instrukcja

8 Października 2024
Hunter

Hunter 53328 Instrukcja

8 Października 2024
Hunter

Hunter Anslee 59266 Instrukcja

8 Października 2024

Instrukcje Wentylator

Najnowsze instrukcje dla Wentylator

Air King

Air King E130SH Instrukcja

10 Października 2024
TriStar

TriStar VE-5936 Instrukcja

10 Października 2024
Orbegozo

Orbegozo PW 1321 Instrukcja

10 Października 2024
Thermex

Thermex Silent 100 CZ Instrukcja

9 Października 2024
Imarflex

Imarflex IF-375BU Instrukcja

9 Października 2024
Imarflex

Imarflex IF-365BK Instrukcja

9 Października 2024
Solis

Solis Charge & Go Fan 7586 Instrukcja

9 Października 2024
Kogan

Kogan KARCDCFANLA Instrukcja

9 Października 2024
Westinghouse

Westinghouse 72206 Instrukcja

9 Października 2024
Westinghouse

Westinghouse 78425 Instrukcja

9 Października 2024