Instrukcja obsługi Hunter Halcyon 81030

Hunter Wentylator Halcyon 81030

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hunter Halcyon 81030 (15 stron) w kategorii Wentylator. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/15
43041-01 09/12/2011
1
Bath Ventilator with Light
Owner’s Manual
Halcyon
43034-01
20110908
©2011 Hunter Fan Co.
Model
81030
English Español
Página 22
43034-01 09/12/2011
2
W A R N I N G
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
1. For general ventilating use only. Do not use to exhaust haz-
ardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy/unbalanced impel-
lers, keep drywall spray, construction dust, etc. off power
unit.
3. DO NOT install this product in a wall. This product is
designed for installation in ceilings up to a 12/12 pitch (45
degrees). Ductwork must point upward.
4. Please read specification label on product for further infor-
mation and requirements.
PREVENTATIVE MAINTENANCE
A clean fan provides better service. Disconnect the power supply and clean the
fan as listed below.
TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a
soft cloth. DO NOT use abrasive cloths, steel wool pads or scouring powders.
TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove
motor plate, find the single tab on the motor plate (located next to the recepta-
cle). Push up rear motor plate tab while pushing out on the side of the housing
or insert a screwdriver into the slot in the housing (next to tab) and twist screw-
driver. Gently vacuum fan, motor and interior of housing.
METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN
WATER.
MAINTENANCE
The motor is permanently lubricated and never needs oiling. If the motor bear-
ings are making excessive or unusual
noises, replace the motor with the exact service motor. You should replace the
impeller at the same time.
W A R N I N GC A U T I O N
1. Use this unit only in a manner intended by the manufacturer. If
you have questions, contact the manufacturer.
2. Before servicing or cleaning the unit, switch power off at ser-
vice panel and lock the service disconnecting means to prevent
power from being switched on accidentally. when the service
disconnecting means cannot be locked, securely fasten a promi-
nent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction.
4. Sufficient air is needed for proper combustion and exhausting
of gasses through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment manufac-
turer’s guideline and safety standards, such as those published
by the National Fire Prevention Association (NFPA), and the
American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall(s) or ceiling, do not
damage electrical wiring or other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must be marked as
appropriate for the application and be connected to a GFCI (Ground
Fault Circuit Interrupter) - protected branch circuit.
8. Never place a switch where it can be reached from a tub or shower.
9. Install fan at least 5 feet (1.52 m) above the floor.
10. This unit must be grounded.
11. Unit must not be installed in a ceiling thermally insulated to a value
greater than R40.
!
!!
DISCONNECT ELECTRIC
POWER SUPPLY
AND LOCK OUT
SERVICE PANEL BEFORE
SERVICING UNIT
Do Not Install Above
Or Inside This Area
Cooking
Equipment
Floor
45° 45°
COOKING AREA
43034-01 09/12/2011
3
x2
D
E
F
G
H
I
L
M
N
95044-01-000
95029-01-000
77481-01-000
03242-07-133
98037-06-000
74508-03-133
98025-01
75184-01-133
Q
x4
*
*
*
NOTE: Strain relief cable connector
must be installed. Not
Included.
A
B
C
Extra Screws
x2
I
3/8” Cable Connec rto
O
P
J
K
65219
66002-01
77539-01
98255-01
98047-01-199
77521-01
12
E
I
Turn off the power source.
Tools Needed.
Estimated assembly time: 30 to 60 minutes
Before Installation
Check all the parts.
If damaged, call
1-888-830-1326
for replacements.
Included.
Loosen screws.
NOTE: Remove all packing materials before installation.

Specyfikacje produktu

Marka: Hunter
Kategoria: Wentylator
Model: Halcyon 81030

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hunter Halcyon 81030, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wentylator Hunter

Hunter

Hunter Nova Instrukcja

12 Stycznia 2025
Hunter

Hunter Bayport Instrukcja

11 Stycznia 2025
Hunter

Hunter Cabo Instrukcja

11 Stycznia 2025
Hunter

Hunter Crystal Peak Instrukcja

2 Stycznia 2025
Hunter

Hunter Malden Instrukcja

2 Stycznia 2025
Hunter

Hunter Neutron Instrukcja

2 Stycznia 2025
Hunter

Hunter Donatella Instrukcja

2 Stycznia 2025
Hunter

Hunter Crestfield Instrukcja

2 Stycznia 2025
Hunter

Hunter Grantham Instrukcja

2 Stycznia 2025
Hunter

Hunter Margo Instrukcja

2 Stycznia 2025

Instrukcje Wentylator

Najnowsze instrukcje dla Wentylator

Sharkoon

Sharkoon SHARK Mirror PWM RGB Instrukcja

22 Marca 2025
Unold

Unold Breezy Bowl 86679 Instrukcja

20 Marca 2025
Lasko

Lasko Motion-Air C27100 Instrukcja

18 Marca 2025
Lasko

Lasko Decor Colors B20401 Instrukcja

18 Marca 2025
Lasko

Lasko Air Flexor 3637 Instrukcja

18 Marca 2025
Lasko

Lasko H20685 Instrukcja

18 Marca 2025
Lasko

Lasko Max Performance 2265QM Instrukcja

18 Marca 2025
Toshiba

Toshiba F-TSA20GMY Instrukcja

18 Marca 2025
Cecotec

Cecotec EnergySilence Aero 3050 Instrukcja

12 Marca 2025
Lasko

Lasko Wind Tower T38305 Instrukcja

10 Marca 2025