Instrukcja obsługi Hunter 23852

Hunter Wentylator 23852

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hunter 23852 (4 stron) w kategorii Wentylator. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Installation in concrete ceiling

CAUTION:

For concrete mounting, the drilled hole must be recommend-

ed by the manufacturer of the anchor (this is usually marked

on the anchor) and must be drilled at least 1/2" deeper than

the length of the anchor.

The holes must be made with a suitable carbide-tipped

masonry drill bit.

The anchors must be new and unused.

The concrete ceiling must be sound and free of cracks or

voids in the vicinity of the mounting holes.

The anchors must be set in flush with the surface of the

concrete.

The bracket screws must never be backed out. If the bracket

screws can be turned easily (by hand), do not hang fan.

Installation

Drill holes 2" deep in concrete ceiling to receive 1/4" x 11

/2"

expansion shield anchor, “Rawl No. 1055” or equal. (Not fur-

nished.) Install shield in holes, observing all cautions above.

Proceed with the installation of the fan per the basic installa-

tion instructions.

The Inside Story

Oil is constantly pumped up the spiral groove to lubricate the

rotor and shaft. The oil is returned to the reservoir where the

bearings are submerged in a bath of oil.

This unique lubrication system is built into all Original Hunter

Ceiling Fans. That’s one reason Hunters last so long. And why

we can offer a Limited Lifetime Warranty.

Fill in the blanks below for your record.

Serial number

Model number

Date purchased Date installed

Dealer/store name where purchased

41121-01 9/95

Trouble shooting guide

Problem Probable Cause Solution

1. Nothing 1. Power turned 1. Turn power on or

happens; off or fuse replace fuse.

blades do blown.

not rotate.* 2. Loose wire 2. Loosen canopy.

connections Check all

or wrong connections (turn

connections. power off while

checking).

3. Pull chain 3. Pull switch cord.

switch not

“on”.

4. Reversing 4. Slide reversing

switch in switch either up or

center. down.

* Note: If blades will not turn by hand, contact your nearest

service representative or dealer.

1. Noisy 1. Blade irons 1. Tighten screws until

operation. loosely snug.

screwed to

rotor.

2. Blade 2. Tighten.

screwed

loosely to

blade iron.

3. Blade cracked. 3. Replace all 4 blades.

Contact dealer.

4. Canopy 4. Lower canopy.

contacting

ceiling.

5. No oil or low 5. Check oil level.

oil level.

1. Excessive 1. Unbalanced 1. Rebalance (See

wobbling blades. Step 7D).

2. Inadequate 2. Relocate fan.

blade

clearance.

3. Loose blades 3. Tighten all screws.

or blade irons.

4. Fan not 4. Turn power off.

secure on Support fan very

hanger carefully. Loosen

assembly. canopy and hang

correctly.

HUNTER FAN COMPANY

25 00 FRISCO AVENUE

M E MP H I S , T N 3 8 1 1 4

Fig. 18

Hanger

Bracket Bracket

Power

Leads

Used With

Light Kit

Canopy

Set Screw

Oil Filler Hole

Oil Return

Rotor

Field

Windings Oil Reservoir

Bearing Nut

Switch Housing Cover

Bushing Pin

Ground Screw

Pipe Nipple (Std.)

Shaft

Cast Iron

Fan Housing

Cast Metal

Lower

Cover

Spiral

Groove

Bearings

Switch Housing

Pull Chain

Switch

expansion

shield anchor

set flush with

ceiling (anchor

not furnished)

Concrete ceiling

Bracket

(Furnished with fan)

Fig. 17

The installation of your Hunter Ceiling Fan

NOTE TO INSTALLERS: Please leave this manual with the

owner.

Tools needed:

• Pliers • 11/64" bit

• Flat blade screwdriver • 3 wire connectors

• Phillips screwdriver • 4" x 11/2" standard octagon

• Electric drill electrical outlet box

• 3/8" Socket wrench

Step 1: Pre-installation

Select installation site: Normally this is near the center of

the room, often replacing a light fixture. Make certain that

ample clearance is left for the rotating fan blades. For maxi-

mum efficiency, no obstruction (walls, posts, etc.) should be

within 24" of the tips of the blades (see Fig. 1). Mounting

site should also meet the precautions listed in Step 3.

Fan mounting height: Your Hunter fan comes with the proper

hardware to hang the fan from a standard 8 foot ceiling so

the fan blades will be 12" from the ceiling and approximately

7 feet from the floor (see Fig. 1).

NOTE: On vaulted ceilings, up to 45° pitch, you may want to

use the Hunter Vaulted Ceiling Mounting Kit.

Step 2: Inspect fan

Unpack the fan carefully to avoid any damage to com-

ponents.

CAUTION: NEVER LIFT THE MOTOR BY THE WIRES.

L E T M OT O R R E S T IN T H E C A R T ON L I N E R F OR

PROTECTION.

Check the sack parts.

Step 3: Installation of ceiling mounting hardware

CAUTION: YOUR HUNTER CEILING FAN WEIGHS UP TO 50

LBS. THE FOLLOWING PRECAUTIONS MUST BE TAKEN FOR

SAFETY AND TO ENSURE THAT YOUR FAN IS SECURELY

MOUNTED TO THE CEILING.

• When inspecting or preparing installation site where wiring

is available, make sure electricity is “off” at fuse box or

circuit breaker panel.

• All wiring must meet local and national codes.

• Do not mount directly to an unsupported ceiling or to an

electrical outlet box.

• The wood joist chosen for mounting the fan must be

sound and of sufficient size. In no case, should it be

smaller than standard 2" x 4" lumber.

Secure a metallic outlet box 4" x 11/2" or 4" x 1/2" deep to

2 x 4 cross brace between two ceiling joists as shown in

Figure 3. The outlet box must be recessed in the ceiling by

1/16" minimum. Secure the outlet box to the cross brace by

drilling (2) pilot holes no larger than the minor diameter of

the woodscrews ( 5/64") and use two #8 x 11

/2" woodscrews

and washers. Use the innermost holes for securing the box.

Orient the box so the outermost holes are aligned with the

2 x 4 brace. The outermost holes will be used in Step 3B.

CAUTION: Do not use a lubricant on screws.

SINCE 1 8 8 6

INSTALLATION INSTRUCTIONS FOR

HUNTER ORIGINAL CEILING FANS

CAUTION:

Read this entire instruction manual thoroughly before

beginning installation and SAVE THESE INSTRUCTIONS.

To avoid possible shock, BE CERTAIN ELECTRICITY IS

SHUT OFF AT MAIN PANEL BEFORE WIRING. Always

turn power off at main panel before servicing your fan or

installing accessories.

All wiring must be in accordance with national and local

electrical codes. If you are unfamiliar with wiring, you

should use a qualified electrician.

To reduce the risk of personal injury, install the fan only

to the building structure according to these instructions,

and use only the hardware supplied.

NEVER REST THE FAN ON THE SWITCH HOUSING. As

you prepare the fan for installation, let the motor rest in

the liner in which it was packed.

Be sure to put full contents of oil tube in fan according to

instructions.

If this fan is used as a replacement for an Original Old-

Tyme non-reversible fan, it must be installed per

instructions included with this fan. DO NOT HANG ON

SINGLE “J” HOOK. Failure to follow these instructions

could result in fan falling.

To reduce the risk of noise do not use a solid-state

speed control with this fan. Use Hunter controls only.

Do not use an abrasive cleaner on the fan. A mild

detergent will clean and restore most units to their

original beauty.

84" min. to floor

24" clearance

Fig. 1

Oil

Rubber Bushing

with Pin

Canopy Screws

Blade Screws

Blade Assembly Screws

Bracket Screws

Hanger Bracket Assembly

Pipe Nipple

in Motor Carton

Bracket

Fig. 2

12" minimum

Drill (2) 11/64" diameter holes through the outermost holes in

the box 2" deep into the cross brace. These holes are for the

bracket screws.

Use the (2) bracket screws to secure the hanger bracket to

the joist as shown in Figure 4. Install rubber bushing in hang-

er bracket before assembling the parts to the ceiling joist. Do

not use lubricant on the screw threads. For an alternate

bracket that fits inside a surface-mounted box, cut 1" off

each end of the bracket supplied.

Step 4: Hanging your fan

CAUTION: BE SURE TO TIGHTEN THE PIPE NIPPLE INTO THE

FAN, AND THE HANGER BRACKET ONTO THE PIPE, AND

TIGHTEN THE 2 SET SCREWS, AS DESCRIBED IN STEP B, TO

PREVENT THE FAN FROM FALLING.

CAUTION: YOUR FAN MAY WEIGHT UP TO 50 LBS. ALL OF

THE FOLLOWING STEPS MUST BE FOLLOWED IN ORDER TO

ENSURE A SECURE MOUNT ING . PERFORM ST EPS A

THROUGH D WITH MOTOR RESTING IN LINER FOR PROTEC-

TION.

Take hanger bracket from sack parts and pipe nipple. Feed

wires from the top of your motor through pipe.

Back out set screw in neck of fan

motor housing and hanger bracket

so pipe can be screwed in. Screw

the pipe into the fan until tight (at

least 41/2turns). Feed wire through

hanger bracket and screw hanger

bracket onto pipe until tight (at least

3 turns). Then use pliers to tighten

both hanger bracket and pipe

together. Tighten the set screw in

the mot or housing wit h pliers.

Securely tighten the set screw in the

hanger bracket. See Figure 5.

Be sure the pin is centered in the

rubber bushing.

See Figures 6 and 7.

Lift the fan by the motor housing,

hook the hanger bracket onto the

pin in the rubber bushing. Make

sure both ends of the pin are

outside the hanger bracket.

See Figure 9. FAILURE TO PER-

FORM THESE STEPS IN COR-

RECT ORDER MAY RESULT IN

FAN FALLING.

Step 5: Wiring instructions and canopy

installation

CAUTION: BE CERTAIN THAT ELECTRICITY IS TURNED OFF

AT THE MAIN PANEL BEFORE ANY WIRING IS DONE.

Before you do the final wiring, you should decide how you want

to control your fan—with pull cord, a wall switch or a speed con-

trol. At this point, you should also decide if you want to add a

light adaptor kit. Separate wiring instructions for Hunter

accessories are included in accessory packages.

Connect black electrical supply lead

to the black motor lead and the

black with white stripe motor lead

(See note). Connect the white elec-

trical supply lead to the white motor

lead. Connect ground wire to green

screw

on side of hanger bracket. See

Figure 8.

NOTE: If a separate wall switch will be used to control a

lighting accessory, connect the black wire with a white

stripe to the wall switch lead, following wiring instructions

included with the accessory. The wall switch must be a list-

ed general-use switch.

CAUTION: NO BARE WIRE OR WIRE STRANDS SHOULD

BE VISIBLE AFTER MAKING CONNECTIONS.

After making the wire connections, the wires should be

spread apart with the white and the green wires on one side

of the outlet box, and the black and black & white wires on

the other side of the box.

The splices should be turned upward and pushed carefully

up into the outlet box.

Canopy installation

Assemble canopy halves around pipe.

Screw together loosely using two

screws provided in parts bag. (Brass

and antique brass canopies are shipped

assembled.) Position canopy close to

ceiling. Tighten both assembly screws

and SCREW IN the canopy set screw.

See Figure 9. NOTE: If a Vaulted Ceiling

Mounting Kit is used, follow the can-

opy instructions provided with the kit.

Step 6: Lubrication

Adding oil

Your fan has been shipped without

oil in the motor. A 1-ounce tube of

high grade SAE 10 non-detergent oil

is packaged in the sack parts. All the

oil in the tube must be put into the

fan. Cut the tip off the tube and place the tube into the oil hole.

To avoid overflowing during filling, allow oil to gravity flow

about one minute to fill the oil reservoir. (It may be necessary

to puncture the tube to allow air in.) See Figure 10.

All wiring must conform to national and local codes which

may vary by locale.

Fig. 3

Fig. 4

Hanger

Bracket

Rubber

Bushing

Bracket

Screws

Rubber

Bushing

Bracket

Screws

Alternate Bracket

Hanger

Bracket

Fig. 5

Fig. 6

Set

Screw

Bushing

Fig 10

Fig 9

Set

Screw

Assembly

Screw

Fig. 8

Fig. 7

Bushing

Set Screws

Min.

84" to

floor

40mm x 80mm WOOD BRACE

CEILING

CEILING JOIST

OUTLET BOX M4 WOOD SCREW

& WASHER (2) REQUIRED

Specyfikacje produktu

Marka:	Hunter
Kategoria:	Wentylator
Model:	23852

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hunter 23852, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wentylator Hunter

Hunter Grove Park 50341 Instrukcja

8 Października 2024

Hunter Charlotte 50402 Instrukcja

8 Października 2024

Hunter Claudette 59622 Instrukcja

8 Października 2024

Hunter Havoc 59470 Instrukcja

8 Października 2024

Hunter Starklake 50409 Instrukcja

8 Października 2024

Hunter Port Royale 50390 Instrukcja

8 Października 2024

Hunter Midtown 54211 Instrukcja

8 Października 2024

Hunter Donegan 53336 Instrukcja

8 Października 2024

Hunter 53328 Instrukcja

8 Października 2024

Hunter Anslee 59266 Instrukcja

8 Października 2024

Instrukcje Wentylator

Najnowsze instrukcje dla Wentylator

Air King E130SH Instrukcja

10 Października 2024

TriStar VE-5936 Instrukcja

10 Października 2024

Orbegozo PW 1321 Instrukcja

10 Października 2024

Thermex Silent 100 CZ Instrukcja

9 Października 2024

Imarflex IF-375BU Instrukcja

9 Października 2024

Imarflex IF-365BK Instrukcja

9 Października 2024

Solis Charge & Go Fan 7586 Instrukcja

9 Października 2024

Kogan KARCDCFANLA Instrukcja

9 Października 2024

Westinghouse 72206 Instrukcja

9 Października 2024

Westinghouse 78425 Instrukcja

9 Października 2024