Instrukcja obsługi Hotpoint WMUD 962G

Hotpoint Pralki WMUD 962G

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint WMUD 962G (16 stron) w kategorii Pralki. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

English,1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Disposal

Opening the porthole door manually

Description of the washing machine, 8-9

Control panel

Display

Running a wash cycle, 10

Wash cycles and functions, 11

Table of wash cycles

Wash functions

Detergents and laundry, 12

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13-14

Assistance, 15-16

WMUD 962

Instructions for use

WASHING MACHINE

Installation

ning the adjustable front feet the (see figure);

angle of inclination, measured according to the

worktop, must not exceed 2°.

Levelling your appliance correctly will provide

it with stability and avoid any vibrations, noise

and shifting during operation. If it is placed on

a fitted or loose carpet, adjust the feet in such

a way as to allow enough room for ventilation

beneath the washing machine.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tap using

a 3/4 gas threaded

connection (see figu-

re).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the other

end of the water inlet

hose to the washing

machine,

screwing it onto the

appliance’s cold water

inlet, situated on the

top right-hand side on

the rear of the applian-

ce (see figure).

3. Make sure there are no kinks or bends in the

hose.

! The water pressure at the tap must be within

the values indicated in the Technical details

table (on the page 5).

! If the water inlet hose is not long enough,

contact a specialist store or an authorised

serviceman.

! Ensure that the supply taps are allowing wa-

ter through. Old taps may seize in the closed

position and thus prevent water reaching the

machine.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

! Keep this instruction manual in a safe place

for future reference. Should the appliance be

sold, transferred or moved, make sure the

instruction manual accompanies the washing

machine to inform the new owner as to its

operation and features.

! Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

Unpacking

! This is a separate

part of the polystyre-

ne base and should

be removed with the

base.

! IMPORTANT check

when unpacking

your machine.

1. Unpack the washing machine.

2. Check whether the washing machine has

been damaged during transport. If this is the

case, do not install it and contact your retailer.

3. Remove the 4 pro-

tective screws and

the rubber bush with

the respective spacer,

situated on the rear of

the appliance (see also

the installation leaflet).

4. Seal the gaps using

the plastic plugs provi-

ded.

5. Keep all the parts:

you will need them again if the washing machi-

ne needs to be moved to another location.

! Packaging materials are not children’s toys.

Levelling

Your machine may make a considerable

amount of noise if the two front feet have not

been adjusted correctly.

1. Install the washing

machine on a flat sturdy

floor, without resting it

up against walls, cabi-

nets or anything else.

2. If the floor is not per-

fectly level, compensa-

te for any unevenness

by tightening or loose-

Connecting the drain hose

Connect the drain

hose, without ben-

ding it, to a draining

duct or a wall drain

situated between 65

and 100 cm from the

floor;

The drain hose may

be connected to

an under-sink trap.

Before connecting

the drain hose from

the machine ensure

that any blanks or

removable ends have

been taken off the

spigot.

If it is placed over

the edge of a basin

or sink be sure the

free end of the hose

should not be under-

water.

! We advise against the use of hose extensions;

in case of absolute need, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into

a standpipe, that the end does not go down

more than 15cms (6 inches). If the hose is pu-

shed down too far, this may cause the machine

to self -syphon ie. continuously empty as it is

filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Tech-

nical Data Plate fixed on the machine;

• the supply voltage is included within the

values indicated on the Technical Data Plate

fixed on the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case, repla-

ce the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD

BE CARRIED OUT BY A QUALIFIED ELECTRI-

CIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be

of the correct colour as indicated by the colou-

red marking or the colour that is embossed in

words on the base of the plug. Replacements

can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moul-

ded plug and you should wish to re-route the

mains cable through partitions, units etc.,

please ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of ap-

proval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Instructions for connecting cable to an alternati-

ve plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Technical data

Model WMUD 962

Dimensions

width 59.5 cm

height 85 cm

depth 60.5 cm

Capacity from 1 to 9 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed up to 1600 rotations per

minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

programme (60°)

( ; 1st press of the button)

Standard Cotton 60°.

programme (40°)

( ; 2nd press of the button)

Standard Cotton 40°.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electromagne-

tic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

As the colours of the wires in the lead may not

correspond with the coloured markings iden-

tifying the terminals in your plug, proceed as

follows:

Connect Green & Yellow wire to terminal

marked or or coloured Green or Green & E

Yellow.

Connect Brown wire to terminal marked or L

coloured Red.

Connect Blue wire to terminal marked or N

coloured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a

13 amp fuse, either in the plug or adaptor or

at the distribution board.

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please re-

move the plug by cutting the mains cable as

close as possible to the plug body and dispo-

se of it as described on the previous page.

! The washing machine should not be installed

in an outdoor environment, not even where

the area is sheltered, because it may be very

dangerous to leave it exposed to damp, rain

and thunderstorms.

! When the washing machine is installed, the

mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

! The power supply cable must only be repla-

ced by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

programme “Auto Clean” (see “Cleaning the

washing machine”).

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Care and maintenance

Cutting off the water and electri-

city supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system in-

side the washing machine and help to prevent

leaks.

• Unplug the washing machine when cleaning

it and during all maintenance work.

Cleaning the washing machine

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The washing machine has a “Auto Clean”

programme for its internal parts that must be

run with no load in the drum.

To help the wash cycle

you may want to use

either the detergent

(i.e. a quantity 10% the

quantity specified for

lightly-soiled garments)

or special additives to

clean the washing ma-

chine. We recommend

running a cleaning

programme every 40 wash cycles.

To start the programme press buttons and A

B simultaneously for 5 seconds (see figure).

The programme will start automatically and will

run for about 70 minutes. To stop the cycle

press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pul-

ling it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

A B

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-clea-

ning pump which does not require any mainte-

nance. Sometimes, small items (such as coins

or buttons) may fall into the pre-chamber which

protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a screwdri-

ver, remove the cover

panel on the lower

front part of the wa-

shing machine (see

figure);

2. unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Specyfikacje produktu

Marka:	Hotpoint
Kategoria:	Pralki
Model:	WMUD 962G

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint WMUD 962G, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Pralki Hotpoint

Hotpoint NSWA 963C WW UK Instrukcja

14 Stycznia 2025

Hotpoint WMAQF 641G UK Instrukcja

14 Stycznia 2025

Hotpoint NSWM 943C GG UK Instrukcja

13 Stycznia 2025

Hotpoint ARTXD 149 Instrukcja

13 Stycznia 2025

Hotpoint BI WMHG 71284 UK Instrukcja

14 Października 2024

Hotpoint WMFUG 742 P UK.M Instrukcja

14 Października 2024

Hotpoint NM11 1044 WC A UK N Instrukcja

12 Października 2024

Hotpoint NSWR 963C GK UK N Instrukcja

12 Października 2024

Hotpoint NSWM 843C GG UK N Instrukcja

8 Października 2024

Hotpoint WMBF 944G UK Instrukcja

8 Października 2024

Instrukcje Pralki

Najnowsze instrukcje dla Pralki

Calor 5023 Instrukcja

9 Kwietnia 2025

Samsung WA12U7 Instrukcja

4 Kwietnia 2025

Whirlpool AWOE 9759 GG Instrukcja

7 Marca 2025

Samsung WA80K2S1 Instrukcja

12 Lutego 2025

Candy CN 44 Instrukcja

16 Stycznia 2025

Candy GO 136-14 Instrukcja

16 Stycznia 2025

Siemens WM6HXKL0DN Instrukcja

15 Stycznia 2025

Indesit XWSNA 610518 W UA Instrukcja

15 Stycznia 2025

Bosch WAQ28440EX Instrukcja

15 Stycznia 2025

Sanyo ASW-602AP Instrukcja

15 Stycznia 2025