Instrukcja obsługi Hotpoint WMSIG 9637BC UK
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint WMSIG 9637BC UK (16 stron) w kategorii Pralki. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/16
1
GB
English,1
GB
WASHING MACHINE
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 6
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 7
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 8-9
Control panel
Display
Running a wash cycle, 10
Wash cycles and options, 11
Table of wash cycles
Wash options
Detergents and laundry, 12
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13-14
Assistance, 15-16
WMSIG 9637
Instructions for use
2
GB
Installation
(see figure); the angle of inclination, measured
according to the worktop, must not exceed 2°.
Levelling your appliance correctly will provide
it with stability and avoid any vibrations, noise
and shifting during operation. If it is placed on
a fitted or loose carpet, adjust the feet in such
a way as to allow enough room for ventilation
beneath the washing machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe to the water
mains using a gas 3/4
attachment, fitting the
rubber gasket and
the filter supplied with
the appliance and
ensuring that they are
fimly tightened to the
taps. The water supply
marked C must be connected to the cold water
tap; the pipe marked must be connected H
to the hot water tap (max. temperature 60°C).
Both pipes may be connected to the cold water
tap using the special connection with multiple Y
attachments, supplied with the appliance (see
figure). Before making the connection, allow the
water to run freely until it is perfectly clear.
2. Connect the inlet
hose to the machine
by screwing it onto
the cold water inlet of
the appliance, which
is situated on the top
right-hand side of
the rear part of the
appliance . (see figure)
3. Make sure there are no kinks or bends in
the hose.
! The water pressure at the tap must be within
the values indicated in the Technical details
table (on the page 5).
! If the water inlet hose is not long enough,
contact a specialist store or an authorised
serviceman.
! Ensure that the supply taps are allowing
water through. Old taps may seize in the
closed position and thus prevent water
reaching the machine.
! Never use second-hand or old inlet hoses;
use the products supplied with the machine.
! Keep this instruction manual in a safe place
for future reference. Should the appliance be
sold, transferred or moved, make sure the
instruction manual accompanies the washing
machine to inform the new owner as to its
operation and features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Unpacking and levelling
Unpacking
! This is a separate
part of the polystyrene
base and should be
removed with the
base.
! IMPORTANT check
when unpacking
your machine.
1. Unpack the washing machine.
2. Check whether the washing machine has
been damaged during transport. If this is the
case, do not install it and contact your retailer.
3. Remove the 4
protective screws and
the rubber bush with
the respective spacer,
situated on the rear of
the appliance (see also
the installation leaflet).
4. Seal the gaps
using the plastic plugs
provided.
5. Keep all the parts:
you will need them again if the washing machine
needs to be moved to another location.
! Packaging materials are not children’s toys.
Levelling
Your machine may make a considerable
amount of noise if the two front feet have not
been adjusted correctly.
1. Install the washing
machine on a flat sturdy
floor, without resting it up
against walls, cabinets or
anything else.
2. If the floor is
not perfectly level,
compensate for
any unevenness by
tightening or loosening
the adjustable front feet
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a draining
duct or a wall drain
situated between 65
and 100 cm from the
floor;
The drain hose may
be connected to
an under-sink trap.
Before connecting
the drain hose from
the machine ensure
that any blanks or
removable ends have
been taken off the
spigot.
If it is placed over
the edge of a basin
or sink be sure
the free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
in case of absolute need, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Ensure that if the drain hose is pushed into
a standpipe, that the end does not go down
more than 15cms (6 inches). If the hose is
pushed down too far, this may cause the
machine to self -syphon ie. continuously empty
as it is filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
• the socket is earthed and in compliance with
the applicable law;
• the socket is able to sustain the appliance’s
maximum power load indicated on the
Technical Data Plate fixed on the machine;
• the supply voltage is included within the
values indicated on the Technical Data Plate
fixed on the machine.
• the socket is compatible with the washing
machine’s plug. If this is not the case,
replace the socket or the plug.
Your appliance is now supplied with a 13 amp
fused plug it can be plugged into a 13 amp
socket for immediate use. Before using the
appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE
EARTHED.
THE FOLLOWING OPERATIONS SHOULD
BE CARRIED OUT BY A QUALIFIED
ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must
be of the correct colour as indicated by
the coloured marking or the colour that is
embossed in words on the base of the plug.
Replacements can be obtained directly from
your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable
moulded plug and you should wish to re-route
the mains cable through partitions, units etc.,
please ensure that either:
the plug is replaced by a fused 13 ampere
rewireable plug bearing the BSI mark of
approval.
or:
the mains cable is wired directly into a 13
amp cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible
without moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot
be accidentally inserted into a socket.
Instructions for connecting cable to an alternative
plug:
Important: the wires in the mains lead are
coloured in accordance with the following
code:
Green & Yellow Earth
Blue Neutral
Brown Live
65 - 100 cm
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap
Specyfikacje produktu
| Marka: | Hotpoint |
| Kategoria: | Pralki |
| Model: | WMSIG 9637BC UK |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hotpoint WMSIG 9637BC UK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Pralki Hotpoint
14 Października 2024
14 Października 2024
12 Października 2024
12 Października 2024
8 Października 2024
8 Października 2024
9 Sierpnia 2024
9 Sierpnia 2024
9 Sierpnia 2024
8 Sierpnia 2024
Instrukcje Pralki
- Pralki Bauknecht
- Pralki Samsung
- Pralki Electrolux
- Pralki DeLonghi
- Pralki AEG
- Pralki Balay
- Pralki Beko
- Pralki Teka
- Pralki LG
- Pralki Amica
- Pralki Gorenje
- Pralki Sharp
- Pralki Russell Hobbs
- Pralki Simpson
- Pralki Bosch
- Pralki Candy
- Pralki Whirlpool
- Pralki Miele
- Pralki Midea
- Pralki Hisense
- Pralki Infiniton
- Pralki Panasonic
- Pralki Baumatic
- Pralki Black & Decker
- Pralki OK
- Pralki Adler
- Pralki Hoover
- Pralki Toshiba
- Pralki Westinghouse
- Pralki Maytag
- Pralki Domo
- Pralki GE
- Pralki Brandt
- Pralki Siemens
- Pralki Haier
- Pralki Cylinda
- Pralki Hyundai
- Pralki Blomberg
- Pralki Fisher & Paykel
- Pralki Indesit
- Pralki Dyson
- Pralki Kenwood
- Pralki Thor
- Pralki Amana
- Pralki Hotpoint Ariston
- Pralki Bomann
- Pralki CDA
- Pralki Philco
- Pralki Neff
- Pralki Corbero
- Pralki Zanussi
- Pralki Fagor
- Pralki Koenic
- Pralki Ardo
- Pralki Manta
- Pralki Pyle
- Pralki KitchenAid
- Pralki Exquisit
- Pralki Arçelik
- Pralki Hanseatic
- Pralki Sanyo
- Pralki SVAN
- Pralki Caple
- Pralki AEG-Electrolux
- Pralki Bush
- Pralki New Pol
- Pralki Kenmore
- Pralki VOX
- Pralki Insignia
- Pralki Orima
- Pralki Kernau
- Pralki Hitachi
- Pralki Zerowatt
- Pralki Frigidaire
- Pralki RCA
- Pralki Kelvinator
- Pralki Gaggenau
- Pralki Avanti
- Pralki Asko
- Pralki Esatto
- Pralki Daewoo
- Pralki Scandomestic
- Pralki Ignis
- Pralki Magic Chef
- Pralki Constructa
- Pralki Euromaid
- Pralki Atlas
- Pralki Zanker
- Pralki Ariston
- Pralki Tricity Bendix
- Pralki Saturn
- Pralki Nordland
- Pralki Zanussi-electrolux
- Pralki Rasonic
- Pralki John Lewis
- Pralki Prima
- Pralki Iberna
- Pralki Logik
- Pralki Currys Essentials
- Pralki Alhafidh
- Pralki Hoover-Helkama
- Pralki Defy
- Pralki Servis
- Pralki Schulthess
- Pralki Marijnen
- Pralki Otsein-Hoover
- Pralki Campomatic
- Pralki Premium
- Pralki White Knight
- Pralki Nordmende
- Pralki Friac
- Pralki Dexter
- Pralki Costway
- Pralki Elba
- Pralki Everglades
- Pralki Saivod
- Pralki Freggia
- Pralki Edesa
- Pralki EAS Electric
- Pralki Lloyd
- Pralki Speed Queen
- Pralki WhiteLine
- Pralki Roper
- Pralki Estate
- Pralki Fram
- Pralki Stoves
- Pralki Edy
- Pralki Upo
- Pralki Trieste
- Pralki Videocon
- Pralki Neufunk
Najnowsze instrukcje dla Pralki
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
15 Października 2024
14 Października 2024