Instrukcja obsługi Hotpoint FML 942 G UK

Hotpoint pralka FML 942 G UK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint FML 942 G UK (4 stron) w kategorii pralka. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Quick Guide

THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.

To receive more comprehensive assistance, register the

appliance on

www.hotpoint.co.uk/register

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

For all testing institutes:

2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.

3) Long wash cycle for synthetics: set wash cycle 5 with a temperature of 40°C.

* By selecting the cycle and excluding the spin cycle, the washing machine will drain only.

The cycle duration indicated on the display or instruction manual is an estimate based on

standard conditions. The actual duration may vary in relation to several factors, such as

the temperature and pressure of the incoming water, ambient temperature, amount of

detergent, load quantity and type, load balancing and any additional options selected.

1) Test wash cycle in compliance with regulation 1061/2010:

This cycle is designed for normally soiled cotton loads and is the most ecient in terms of

both electricity and water consumption; it should be used for garments washable at 60°C or

at 40°C. The actual washing temperature may dier from the indicated value.

PRODUCT DESCRIPTION

1. Top

2. Detergent dispenser drawer

3. Control panel

4. Handle

5. Porthole door

6. Drain pump (behind the plinth)

7. Plinth (removable)

8. Adjustable feet (2)

DETERGENT DISPENSER DRAWER

Compartment *:

Do not insert detergent in this compartment.

Compartment 1: Washing detergent (powder

or liquid)

If liquid detergent is used, the removable plastic

partition (supplied) should be used for proper A

dosage.

If powder detergent is used, place the partition

into slot .B

Compartment 2: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “MAX” level.

! Use powder detergent for white cotton garments, for pre-washing, and

for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

WASH CYCLE TABLE

1. ON/OFF button

2. TEMPERATURE knob

3. SPIN SPEED knob

4. WASH CYCLE PROGRESS indicator lights

5. DOOR LOCKED indicator light

6. START/PAUSE button and indicator light

7. OPTION buttons and indicator lights

8. WASH CYCLE SELECTOR KNOB

Maximum load 9 kg

Power input in o mode 0.5 W / in left-on mode 8 W

Detergents and

Additives

Recommended

detergent

Residual

dampness %

Energy con-

sumption kWh

Total water l

Wash cycle Temperature Max.

spin speed

(rpm)

Max.

load

(kg)

Duration

(minutes)

Wash Fabric

softener Powder Liquid

Default Range 1 2

1 Anti Stain 40°C - 40°C 1400 5 180’   –– – –

2 Whites 60°C - 90°C 1400 9 145’     – – –

3 Cotton (2) 40°C - 60°C 1400 9 225’   –53 1.10 97

4 Eco Cotton 60° - 40° (1) 60°C 60°C 1400 9 250’     53 1.30 57.4

40°C 1400 9 225’     53 1.10 97

5 Synthetics (3) 40°C - 60°C 1000 4.5 125’   –46 0.56 65

6 Anti Allergy Plus 60°C - 60°C 1400 5 195’     – – –

7 Baby 40°C - 40°C 1000 5 145’   –– – –

8 Bed & Bath 60°C - 60°C 1400 9 140’     – – –

9 Fast Wash 60’ 60°C - 60°C 1400 3.5 60’     – – –

10 Fast Wash 30’ 30°C - 30°C 800 3.5 30’   –– – –

11 Cotton 20°C 20°C - 20°C 1400 9 175’   –– – –

12 Shirts 40°C - 40°C 600 2 80’   –– – –

13 Wool 40°C - 40°C 800 2 85’   –– – –

14 Delicates 30°C - 30°C 0 1 80’   –– – –

Rinse – – 1400 9 50’ – – – – – –

Spin + Pump Out * – – 1400 9 10’ – – – – – – –

 Required dosage Optional dosage

WASH CYCLES

Follow the instructions on the symbols of the garment’s wash

care label. The value indicated in the symbol is the maximum

recommended temperature for washing the garment.

Anti Stain

The programme is suitable to heavily-soiled garments with resistant

colours. It ensures a washing class that is higher than the standard class (A

class). When running the programme, do not mix garments of dierent

colours. We recommend the use of powder detergent. Pre-treatment with

special additives is recommended if there are obstinate stains.

Whites

Heavily soiled whites and resistant colours.

Cotton

Lightly soiled resistant and delicate colours.

Eco Cotton 60° - 40°

Suitable for washing moderately soiled cotton garments. At 40°C and

60°C it is the standard cycle for washing cotton garments, and is the most

ecient in terms of combined water and electricity consumption.

Synthetics

Suitable for washing moderately soiled garments made of synthetic bres

(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.

Anti Allergy Plus

Suitable for removing major allergens such as pollen, mites and cat or dog hair.

Baby

Use the special wash cycle to remove the soiling typically caused by

babies, while removing all traces of detergent from nappies in order to

prevent the delicate skin of babies from suering allergic reactions. The

cycle has been designed to reduce the amount of bacteria by using a

greater quantity of water and optimising the eect of special disinfecting

additives added to the detergent.

Bed & Bath

Use programme to wash bed linen and towels in one single cycle: it

optimises softener performance and helps you save time and energy. We

recommend the use of powder detergent.

Fast Wash 60’

For washing normal soiled garments in a short time. Not suitable for wool,

silk and garments to be washed by hand.

Fast Wash 30’

For washing lightly soiled garments in a short time. Not suitable for wool,

silk and garments to be washed by hand.

Cotton 20°C

The programme ideal for lightly soiled cotton loads. The eective

performance levels achieved at cold temperatures, which are comparable

to washing at 40°, are guaranteed by a mechanical action which operates

at varying speed, with repeated and frequent peaks.

Shirts

Use the special wash cycle to wash shirts in dierent fabrics and colours

to guarantee they receive the best possible care.

Wool - Woolmark Apparel Care - Green:

The “Wool” wash cycle is approved by the Woolmark

Company for washing wool garments classied as

“hand-washable”, provided that the wash complies with

the instructions appearing on the garment’s label and

with those provided by the manufacturer of this washing

machine. (M1127)

Delicates

For washing very delicate garments. It is advisable to turn the garments

inside out before washing them. For best results, use liquid detergent on

delicate garments. Use liquid detergent on delicate garments for best results.

To wash silk garments and curtains select cycle 14 and then option “Easy Iron”;

the machine will end the cycle while the laundry is soaking, the “Easy Iron” and

START/PAUSE indicator lights will ash (orange) and the RINSE phase will

remain lit in a xed manner. To drain the water so that the laundry may be

removed, press the START/PAUSE button or the “Easy Iron” button.

Rinse

Designed for rinsing and spinning.

Spin + Pump out

Designed for spinning and draining the water.

INDICATOR LIGHTS

The indicator lights provide important information. This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has begun, the

indicator lights switch on one by one to indicate which phase of the cycle

is currently in progress.

Door locked indicator light

If this indicator light is on, the appliance door is locked to prevent it from

being opened accidentally; to avoid any damage, wait for the indicator

light to switch o before you open the appliance door (wait

approximately 3 minutes).

! If the START/PAUSE indicator light (orange) ashes rapidly at the same

time as the option indicator light, this indicates a problem has occurred

(see “Troubleshooting”).

FIRSTTIME USE

Once the appliance has been installed, and before it is used for the rst

time, run a wash cycle with detergent and no laundry, by setting the

“Auto-Clean” cycle.

DAILY USE

Prepare the laundry by following the suggestions appearing under the

“TIPS AND SUGGESTIONS” section.

- Press the ON/OFF button ; all the indicator lights will turn on for a few

seconds, then only the indicator lights relative to the selected programme

settings will remain lit and the START/PAUSE indicator light will ash.

- Open the door. Load the laundry while making sure not to exceed the

maximum load quantity indicated in the wash cycle table.

- Pull out the detergent dispenser drawer and pour the detergent into the

relevant compartments, as described in the “DETERGENT DISPENSER

DRAWER” section.

- Close the door.

- Select the desired wash cycle.

- Set the washing temperature.

- Set the spin speed.

- Select the desired options.

- Press the START/PAUSE button to start the wash cycle; the relative

indicator light will light up steady green and the door will lock (the

indicator light will switch on).

PAUSING A CYCLE

To pause the wash cycle, press the START/PAUSE button again; the

indicator light will ash amber. To start the wash cycle from the point at

which it was interrupted, press the START/PAUSE button again.

OPENING THE DOOR, IF NECESSARY

Once a cycle starts, the indicator light turns on to signal that the door

cannot be opened. While a wash cycle is running, the door remains

locked. To open the door while a cycle is under way, for example, to add

or remove garments, press the START/PAUSE button to pause the

cycle; the indicator light will ash amber. If the indicator light is not lit,

the door may be opened. Press the START/PAUSE button again to

continue the cycle.

CHANGING A RUNNING WASH CYCLE

To change a wash cycle while it is in progress, pause the washing machine

using the START/PAUSE button (the relative indicator light will ash

amber), then select the desired cycle and press the START/PAUSE

button again.

! To cancel a cycle that has already begun, press and hold the ON/OFF

button. The cycle will be stopped and the machine will switch o.

AT THE END OF THE WASH CYCLE

At the end of the wash cycle the indicator light will switch on; when

the indicator light switches o, the door may be opened (wait

approximately 3 minutes). Open the door, unload the laundry and switch

o the machine. If you do not press ON/OFF button, the washing

machine will switch o automatically after about a half of an hour.

OPTIONS

- If the selected option is not compatible with the programmed wash

cycle, the corresponding indicator light will ash and a sound alert (3

beeps); the option will not be activated.

- If a option which is incompatible with another function selected

previously, only the most recent selection will remain active.

Super Wash

This option oers a high-performance wash due to the greater quantity of

water used in the initial phase of the cycle, and due to the increased wash

cycle duration, is particularly useful for the removal of stubborn stains.

Extra Rinse

Selecting this option allows for enhancing rinsing eciency and fully

removing the detergent. It is particularly useful for sensitive skin.

Easy Iron

By selecting this function, the wash and spin cycles will be modied in

order to reduce the formation of creases. At the end of the cycle the

washing machine will perform slow rotations of the drum; the EASY IRON

and START/PAUSE indicator lights will ash (orange) and the phase

will remain lit in a xed manner. To end the cycle, press the START/PAUSE

button or the EASY IRON button.

Timer Saver

If you select this option, the wash cycle duration will be reduced by up to

50%, depending on the selected cycle, thereby guaranteeing

simultaneous water and energy saving. Use this cycle for lightly soiled

garments.

Wash

Rinse

Spin

Pump out

End of wash cycle

END

Temperature

Turn the TEMPERATURE knob to set the wash temperature (see Wash

cycles table).

The temperature may be lowered, or even set to a cold wash ( ).

The washing machine will automatically prevent you from selecting a

temperature which is higher than the maximum value set for each wash cycle.

Spin

Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.

The spin speed may be lowered, or the spin cycle can be excluded

altogether by selecting the symbol .

The washing machine will automatically prevent you from selecting a spin

speed which is higher than the maximum speed set for each wash cycle.

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

CARE AND MAINTENANCE

Before performing cleaning and maintenance, switch the washing machine

o and disconnect it from the mains power. Do not use ammable liquids to

clean the washing machine.

Cutting o the water and electricity supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washing machine and help to prevent leaks.

Unplug the washing machine when cleaning it and during all

maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance can be cleaned

using a soft cloth soaked in lukewarm soapy water. Do not use solvents or

abrasives.

The washing machine has a “Auto-Clean” cycle for its internal parts; it

must be run without any load in the drum.

To optimise this cycle, it is possible to use either detergent (10% of the

quantity specied for lightly soiled garments) or special additives to clean

the washing machine. We recommend running a cleaning cycle every 40

wash cycles.

To start the cycle press buttons “Super Wash” and “Extra Rinse”

simultaneously for 5 seconds.

The cycle will start automatically and will run for about 70 minutes. To

stop the cycle, press the START/PAUSE button.

Cleaning the detergent dispenser drawer

Remove the dispenser drawer by lifting and pulling it outwards. Wash it

under running water; this procedure should be eected regularly.

Caring for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant

odours from forming.

Cleaning the pump

The washing machine is tted with a self-cleaning pump that does not

require any maintenance. Small items (such as coins or buttons) may

sometimes fall into the protective pre-chamber situated at the base of the

pump.

! Make sure that the wash cycle has ended and unplug the appliance.

To access the pre-chamber:

1. remove the covering panel on the front side of the machine by

inserting a screwdriver in the centre and sides of the panel and using it as

a lever;

2. loosen the drainage pump cover by turning it anti-clockwise: it is

normal for some water to leak out;

3. clean the inside thoroughly;

4. screw the cover back on;

5. put the panel back in place, making sure the hooks slot in place before

pushing the panel onto the appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If it is cracked or broken, it

must be replaced: during wash cycles, the high pressure of the water

could suddenly split the hose open.

! Never use hoses that have already been used.

LOAD BALANCING SYSTEM

Before every spin cycle, to avoid excessive vibrations before every

spin and to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the washing

rotation speed. If, after several attempts, the load is not balanced

correctly, the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs the distribution

process instead of spinning. To encourage improved load distribution and

balance, we recommend small and large garments are mixed in the load.

ACCESSORIES

Contact our Technical Assistance Service to check whether the following

accessories are available for this washing machine model.

Stacking kit

With this accessory you can secure the tumble dryer to the upper part of

your washing machine to save space and facilitate loading and unloading

of the tumble dryer.

TRANSPORT AND HANDLING

Do not lift the washing machine by gripping it from the upper section.

Unplug the appliance and close the water tap. Check that the door and

detergent dispenser drawer are tightly closed. Detach the lling hose

from the water tap then detach the drain hose. Empty all the water

remaining in the hoses and secure the latter so that they do not get

damaged during transport. Apply the transport bolts back on. Repeat, in

reverse order, the transport bolt removal procedure described in the

“Installation instructions”.

Important: Not emptying contents from pockets may cause pump or drain

blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are

not intended as machine washable.

Specyfikacje produktu

Marka:	Hotpoint
Kategoria:	pralka
Model:	FML 942 G UK

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint FML 942 G UK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje pralka Hotpoint

Hotpoint WMG 942BV EU Instrukcja

15 Stycznia 2025

Hotpoint WMTG 6526BS IT Instrukcja

15 Stycznia 2025

Hotpoint NFR79W IT Instrukcja

8 Stycznia 2025

Hotpoint NF97WK IT Instrukcja

8 Stycznia 2025

Hotpoint NFR527W Instrukcja

29 Grudnia 2024

Hotpoint NBT 946 WM A IT Instrukcja

29 Grudnia 2024

Hotpoint NF95W IT N Instrukcja

29 Grudnia 2024

Hotpoint NSWA 1146 WW UK Instrukcja

29 Grudnia 2024

Hotpoint H8 99AD GPOWER UK Instrukcja

29 Grudnia 2024

Hotpoint NLCD1048WDAUK Instrukcja

16 Grudnia 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Samsung p 1453 gw Instrukcja

15 Stycznia 2025

Bauknecht WA Black 714 BW BK Instrukcja

15 Stycznia 2025

Beko WTV8814MMC1 Instrukcja

15 Stycznia 2025

Daewoo DWD-FD1441 Instrukcja

15 Stycznia 2025

Indesit W 144 XS Instrukcja

15 Stycznia 2025

Beko WMY71464STR1 Instrukcja

15 Stycznia 2025

Whirlpool AWE 6720 Instrukcja

15 Stycznia 2025

Indesit WN860WSK Instrukcja

15 Stycznia 2025

Whirlpool WGD7000D Instrukcja

15 Stycznia 2025

AEG-Electrolux l 88819 Instrukcja

15 Stycznia 2025