Instrukcja obsługi Hotpoint FDD914P

Hotpoint Pomywaczka FDD914P

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint FDD914P (20 stron) w kategorii Pomywaczka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
Instruction booklet
,1509)50-4
Contents
Installation, 2-5
Positioning and levelling
Technical data
Electrical connection
Connecting the water supply
Description of the appliance, 6
Overall view
Control panel
Loading the racks, 7
Lower rack
Cutlery basket
Upper rack
Start-up and use, 8-9
Starting the dishwasher
Loading the detergent
Washing options
Wash cycles, 10
Wash cycle table
Rinse aid and refined salt, 11
Loading the rinse aid
Loading the refined salt
Care and maintenance, 12
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 13-14
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 15
After Sales Service, 16
After Sales Service
Essential Contact Information
Parts and Accessories
Appliance Registration
Hotpoint Guarantee, 17
.,, '"
EN
English, 1
2
EN
Positioning and levelling
1. Remove the appliance from all packaging and check
that it has not been damaged during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Check the dishwasher by placing it so that its sides or
back panel are in contact with the adjacent cabinets or
even with the wall. This appliance can also be recessed
under a single worktop* (see the Assembly instruction
sheet).
3. Position the dishwasher on a level and sturdy floor. If
the floor is uneven, the front feet of the appliance may be
adjusted until it reaches a horizontal position (the angle of
inclination must not exceed 2 degrees). If the appliance is
levelled correctly, it will be more stable and much less
likely to move or cause vibrations and noise while it is
operating.
4*. Adjust the height of the rear foot from the front of the
appliance* on the central lower part of the dishwasher,
turning a hexagonal spanner (red color) with an opening
of 8 mm in a clockwise direction to increase the height
or in an anticlockwise direction to decrease the height.
Anti-condensation strip*
After installing the dishwasher, open the door and stick
the adhesive transparent strip under the wooden shelf in
order to protect it from any condensation that may form.
Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given away or
moved, please ensure the manual is kept with the
machine, so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully: it
contains important information regarding the safe
installation, use and maintenance of the appliance.
If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be
tilted onto its back.
Advice regarding the first wash cycle
After the appliance has been installed, immediately
before running the first wash cycle, completely fill the
salt dispenser with water and add only then
approximately 1 kg of salt (see chapter entitled Rinse aid
and refined salt). The water may overflow: this is normal
and is not a cause for concern. Select the water
hardness value (see chapter entitled Rinse aid and
refined salt). - After the salt has been poured into the
machine, the LOW SALT indicator light* switches off.
If the salt container is not filled, the water softener
and the heating element may be damaged as a result.
* Only available in selected models.
Installation
Technical data
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 14 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply
voltage See appliance data plate
Total absorbed
power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to
the following European
Community Directives:
-2006/95/CE dated 16/01/2007
(Low Voltage) and subsequent
modifications
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
-2002/96/ CE Waste Electrical
and Electronic Equipment
(WEEE)
3
EN
The dishwasher meets the requirements set out by
the regulations in force concerning safety and electrical
equipment.
Any technical checks should be conducted
exclusively by a trained and authorised technician:
Repairs carried out by unaithorised persons will
invalidate the guarantee, as well as posing a potential
hazard to the user.
The manufacturer declines all responsibility for
damage to persons or property resulting from failure to
observe the above precautions, from tampering with
even a single component or from the use of non-original
spare parts.
Electrical Connection
Before inserting the plug into the electrical socket, make
sure that:
the socket is earthed and complies with current
regulations;
the socket can withstand the maximum load of the
appliance, which is indicated on the data plate
located on the inside of the door (see Description of
the appliance);
the power supply voltage falls within the values
indicated on the data plate on the inside of the door;
the socket is compatible with the plug of the
appliance. If this is not the case, ask an authorised
technician to replace the plug (see Assistance); do
not use extension cables or multiple sockets.
Once the appliance has been installed, the power
supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be
replaced by the manufacturer or its Technical
Assistance Service in order to prevent all potential
hazards. (See Assistance)
This appliance must be earthed.
Fuses:your appliance comes fitted with a plug and a 13A
fuse. If you need to replace the fuse, only those rated at
13A and ASTA approved to BS1362 should be used. If
you lose the fuse cover, a replacement may be obtained
from your local authorised Service Centre or Electrical
company. Correct replacement is identified by colour
coding or the marking on base of plug.
DO NOT use the plug unless the fuse cover is fitted.
Changing the Plug
Cut off and dispose of the supplied plug if it does not
fit your socket.
To avoid a shock hazard DO NOT insert the
discarded plug into a socket anywhere else.
Wires in the mains lead are coloured accordance with
the following code:
Green/Yellow - Earth
Blue - Neutral
Brown - Live
If you change the plug, the colour of the wires in the
mains lead may not correspond with the terminal
markings in the plug, which if not coloured, could be:
EARTH E or
NEUTRAL N
LIVE L
Changing the Mains Lead
A lead can be ordered from Hotpoint Service
UK: 08709 066 066 or
Republic of Ireland: 1850 302 220
- If you have damaged the existing lead or require a
longer one a charge will be made. It is strongly advised
that this work is carried out by a qualified electrician.
- If the domestic wiring includes a residual current-
operated circuit breaker, ensure that it conforms to the
latest regulations.
The dishwasher must not be connected to the
electricity supply while installation is being carried out.
- This appliance should only be connected to a 230/
240V AC source, via a properly installed earthed socket.
- Use the dishwasher solely in a domestic environment.
- DO NOT stand or place heavy objects on the door
when it is open, this could damage the door or cause the
appliance to tip forward.
The Company shall not be held responsible for any
incidents that occur if these regulations are not
observed.

Specyfikacje produktu

Marka: Hotpoint
Kategoria: Pomywaczka
Model: FDD914P

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint FDD914P, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Pomywaczka Hotpoint

Hotpoint

Hotpoint HA3FC10BS7A0S Instrukcja

8 Stycznia 2025
Hotpoint

Hotpoint HSFO 3T223 WC X Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HI 5030 WEF Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HFO 3O32 CW X Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HIC 3C26N WF Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HIC 3C26 CW Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HIE 2B19 C N Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HSFC 3T127 C Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HB 4010 B Instrukcja

12 Grudnia 2024
Hotpoint

Hotpoint HFC 3T232 WG Instrukcja

12 Grudnia 2024

Instrukcje Pomywaczka

Najnowsze instrukcje dla Pomywaczka

AEG

AEG F88080IA Instrukcja

15 Stycznia 2025
Candy

Candy CI 7300 Instrukcja

15 Stycznia 2025
Miele

Miele G 1220 SC Instrukcja

15 Stycznia 2025
Inventum

Inventum VVW7020 Instrukcja

15 Stycznia 2025
AEG

AEG F56322W0 Instrukcja

15 Stycznia 2025
AEG

AEG FFB52600ZM Instrukcja

15 Stycznia 2025
AEG

AEG F55000W0 Instrukcja

15 Stycznia 2025
Indesit

Indesit idl 600 Instrukcja

15 Stycznia 2025
Atag

Atag VA2013RT Instrukcja

15 Stycznia 2025
Atag

Atag VA8017SRT Instrukcja

15 Stycznia 2025