Instrukcja obsługi Hotpoint BI WDHG 961484 UK

Hotpoint pralka BI WDHG 961484 UK

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint BI WDHG 961484 UK (4 stron) w kategorii pralka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Quick Guide

THANK YOU FOR PURCHASING A PRODUCTHOTPOINT .

To receive more comprehensive assistance, register the

appliance on

www.hotpoint.eu/register

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

WASH CYCLE TABLE

Note: spin speed values shown on the display can slightly differs from the values stated in the table.

For all testing institutes:

2) Long cotton cycle: set programme 5 at temperature 40°C.

3) Long synthetics cycle: set cycle 6 at a temperature of 40°C.

* By selecting the cycle and excluding the spin cycle, the washer-dryer will drain only.

** The duration of the programme is shown on the display.

*** After programme end and spinning with maximum selectable spin speed, in default

programme setting.

**** The display will show the suggested spin speed as default value.

For wash programmes with temperatures above 50°C, we recommend using powder detergent

rather than liquid, and following the directions given on the detergent package.

This data may dier in your home due to changing conditions in inlet water temperature,

water pressure etc. Approximate programme duration values refer to the default setting of

the programmes, without options.

The values given for programmes other than the Eco 40-60

programme are indicative only.

For all Test Institutes

Eco 40-60 (Wash)- Test wash cycle in compliance with EU Ecodesign regulation 2019/2014. The most

efficient programme in terms of energy and water consumption for washing normally soiled cotton

laundry.

4) Eco 40-60 (Wash&Drying)-

Test

wash&

drying cycle in compliance with EU Ecodesign

regulation

2019/2014

. To access “wash and dry” cycle select “Eco 40-60” wash programme

and set “Drying” option level to

“ ”.

The most ecient programme in terms of energy and

water consumption for washing and drying normally soiled cotton laundry. At the end of cycle

the garments can be immediately stored to the cupboard.

Maximum load 9 kg

Power input in o mode 0.5 W / in left-on mode 8 W Detergents and

Additives Recommended

detergent

Residual

dampness %

(***)

Energy

consumption

kWh

Total water lt

Laundry

temperature °C

Wash cycle Temperature Maximum

spin

(r.p.m.)

Max. load

for wash

cycle (kg)

Max. load

for drying

cycle (kg)

Duration

(h : m)

Drying

Wash Fabric

softener Powder Liquid

Setting Range 2 3

1 Mixed Wash&Dry 40 °C 800 3,5 3,5 **40 °C    –– – – –

2 Shirts and T-shirts 40 °C 1000 2,0 2,0 **40 °C    –– – – –

3 Pre Iron – – – 2,0 – ** – – – – – – – – –

4 Steam Refresh – – – 2,0 – ** – – – – – – – – –

5 Cotton (2) 40 °C - 60 °C 1400 9,0 6,0 3:55      49 1,4 105 45

6 Synthetics (3) 40 °C - 60 °C 1200 4,0 4,0 2:55      35 0,8 55 43

7 Anti Stain Quick 40 °C - 40 °C 1200 4,5 4,5 **    –– – – –

8 Anti Stain 40° 40 °C - 40 °C 1400 9,0 6,0 **    –– – – –

9 White 60 °C - 90 °C 1400 9,0 6,0 2:45      49 0,9 90 55

10 Eco 40-60 (1)

(Wash) 40 °C 40°C

1351 9,0 6,0 3:40      53,5 0,86 54 38

1351 4,5 3,0 2:50      53,5 0,68 54 37

1351 2,5 – 2:10      53,5 0,46 40 34

11 20°C 20 °C - 20 °C 1400 9,0 6,0 1:50    –49 0,2 90 22

12 Delicates 30 °C - 30 °C 600

(****) 1,0 1,0 **    –– – – –

13 Wool 40 °C - 40 °C 800 2,0 2,0 **    –– – – –

14 Rapid 30‘ 30 °C - 30 °C 1200

(****) 4,5 - 0:30 –   –71 0,2 45 27

Rinse & Spin – – 1400 9,0 6,0 – –– – – – – –

Spin & Drain * – – 1400 9,0 6,0 – – – – – – – – –

  Required dosage Optional dosage

10 Eco 40-60 (4)

(Wash&Drying) 40 °C 40 °C 1351 6,0 6,0 9:20      0 3,80 75 33

1351 3,0 3,0 5:10      0 1,98 47 32

1. ON/OFF button

2. START/PAUSE button

3. TEMPERATURE button

4. ENERGY SAVER button

5. DRY ONLY button / Lock

button

6. DRYING SETTINGS button

7. START DELAY button

8. SPIN SPEED button

9. WASH CYCLE SELECTOR KNOB

1 2 5

DISPLAY INDICATORS

Washing phase

Indicates washing phase of the cycle

Drying phase

Energy Saver activated

Key lock activated

Drying only

Time drying mode

Drying automatic levels

Start delay activated

Door locked

PRODUCT DESCRIPTION

1. Worktop

2. Detergent dispenser

3. Control panel

4. Door handle

5. Door

6. Water lter

7. Adjustable feet (4)

DETERGENT DISPENSER

Compartment 1:

Do not insert detergent in this compartment.

Compartment 2: Washing detergent

(powder or liquid)

Compartment 3: Additives (fabric softeners,

etc.)

The fabric softener must not exceed the “MAX”

level.

! Use powder detergent for white cotton

garments, for pre-washing, and for washing at

temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

! This symbol reminds you to read this instruction manual.

WASH CYCLES

Follow the instructions on the symbols of the garment’s wash

care label. The value indicated in the symbol is the maximum

recommended temperature for washing the garment.

Mixed Wash&Dry

use programme 1 to wash and dry mixed garments (cotton and

synthetics). This cycle may be used to wash and dry loads of up to 3,5 kg;

we recommend the use of liquid detergent.

The use of the steam in this programme is optimised to reduce the

formation of creases on garments, making them easier to iron.

Shirts and T-shirts

Use programme 2 to wash and dry shirts and T-shirts in dierent fabrics

and colours to ensure maximum care. This cycle may be used to wash

and dry loads of up to 2 kg. To achieve optimum results, use liquid

detergent and pre-treat cus, collars and stains. The use of the steam in

this programme is optimised to reduce the formation of creases on

garments, making them easier to iron.

Pre Iron

Use this programme immediately before ironing; max. 2 kg load. The use

of the steam in this programme is optimised to reduce the formation of

creases on garments, making them easier to iron.

Steam Refresh

For refreshing garments, neutralised unpleasant odours and relaxing the

bres by delivering steam into the drum. The garments will be damp at

the end of the cycle.

Cotton

Suitable for washing towels, underwear, table cloths, etc. made of

resistant linen and cotton that are moderately to heavily soiled.

Synthetics

Suitable for washing moderately soiled garments made of synthetic

bres (e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton

bres.

Anti Stain Quick

this programme is ideal for washing the most dicult daily stains in 1

hour. It is ideal for mixed fabrics and coloured garments, caring for your

clothes as it washes.

If the drying function is selected, a drying cycle automatically activates at

the end of the wash cycle that resembles open-air drying, with the added

advantages of preserving garments from yellowing due to sunlight

exposure and preventing loss of whiteness caused by the possible

presence of dust in the air. Dryness level “ ” recommended.

Anti Stain 40°

the programme is suitable to heavily-soiled garments with resistant

colours. It ensures a washing class that is higher than the standard class (A

class). When running the programme, do not mix garments of dierent

colours. We recommend the use of powder detergent. Pre-treatment with

special additives is recommended if there are obstinate stains.

If the drying function is selected, a drying cycle automatically activates at

the end of the wash cycle that resembles open-air drying, with the added

advantages of preserving garments from yellowing due to sunlight

exposure and preventing loss of whiteness caused by the possible

presence of dust in the air. Dryness level “ ” recommended.

White

For heavily soiled whites and resistant colours.

Eco 40-60

For washing normally soiled cotton garments declared to be washable at 40 °C

or 60 °C, together in the same cycle. This is the standard cotton programme

and the most ecient in terms of water and energy consumption.

20°C

For washing lightly soiled cotton garments, at a temperature of 20 °C.

Delicates

For washing very delicate garments. It is advisable to turn the garments

inside out before washing them. For best results, use liquid detergent on

delicate garments.

We recommend turning the garments inside out before washing and

placing small items into the special bag for washing delicates. Use liquid

detergent on delicate garments for best results.

When selecting an exclusively time-based drying function, a drying cycle is

performed at the end of the wash cycle that is particularly delicate, thanks

to light handling and appropriate temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric composition.

Wool - Woolmark Apparel Care - Green:

the wool wash cycle of this machine has been approved by

The Woolmark Company for the washing of wool garments

labelled as “hand wash” provided that the products are

washed according to the instructions on the garment label

and those issued by the manufacturer of this washer-dryer.

(M1318)

Rapid 30‘

For washing lightly soiled garments in a short time. Not suitable for wool,

silk and garments to be washed by hand.

Rinse & Spin

Designed for rinsing and spinning.

Spin & Drain

Designed for spinning and draining the water.

Door locked indicator

if the symbol is o the door is locked. To prevent any damage, wait

until the symbol turns on before opening the door.

To open the door while a cycle is in progress, press the START/PAUSE

button ; if the symbol is lit, the door can be opened.

FIRSTTIME USE

Once the appliance has been installed, and before it is used for the rst

time, run a wash cycle with detergent and no laundry, by setting the cycle

9(60°C).

DAILY USE

Prepare the laundry by following the suggestions appearing under the

“TIPS AND SUGGESTIONS” section.

- Press the ON/OFF button ; the indicator light relative to START/PAUSE

will ash slowly.

- Open the door. Load the laundry while making sure not to exceed the

maximum load quantity indicated in the wash cycle table.

- Pull out the detergent dispenser drawer and pour the detergent into the

relevant compartments, as described in the “DETERGENT DISPENSER

DRAWER” section.

- Close the door.

- The machine automatically displays the default temperature and spin

speed values for the selected cycle, or the most recently used settings if

they are compatible with the selected cycle.

- Select the desired wash cycle.

- Select the desired options.

STARTING CYCLE

Press the START/PAUSE button.

The machine will lock the door ( symbol OFF) and the drum will start to

rotate; the door will be unlocked ( symbol on) and then locked again (

symbol OFF) as preparation phase of each washing cycle. The “Clicking”

noise is part of the door locking mechanism. Water will enter the drum

and start the washing phase once the door is locked.

PAUSING A CYCLE

To pause the wash cycle, press the START/PAUSE button again; the

indicator light will ash. If the symbol is lit, the door may be opened. To

start the wash cycle from the point at which it was interrupted, press the

START/PAUSE button again.

OPENING THE DOOR, IF NECESSARY

Once a cycle starts, the symbol turns o to signal that the door cannot

be opened. While a wash cycle is running, the door remains locked. To

open the door while a cycle is under way, for example, to add or remove

garments, press the START/PAUSE button to pause the cycle; the

indicator light will ash. If the symbol is lit, the door may be opened.

Press the START/PAUSE button again to continue the cycle.

CHANGING A RUNNING WASH CYCLE

To change a wash cycle while it is in progress, pause the washer-dryer using

the START/PAUSE button (the relative indicator light will ash), then

select the desired cycle and press the START/PAUSE button again.

! To cancel a cycle that has already begun, press and hold the ON/OFF

button. The cycle will be stopped and the machine will switch o.

AT THE END OF THE WASH CYCLE

This will be indicated by the word “END” on the display; when the

symbol switches on, the door may be opened. Open the door, unload the

laundry and switch o the machine. If you do not press “ON/OFF”

button, the washing machine will switch o automatically after about a

10 minutes. Close the water tap, open the door and unload the washing

machine. Leave the door ajar to allow the drum to dry.

OPTIONS

! If the selected option is incompatible with the programme set, the

incompatibility will be signalled by a buzzer and the corresponding

indicator light will ash.

! If the selected option is incompatible with another previously set

option, only the most recent selection will remain active.

Energy saver

This option saves energy by not heating the water used to wash your

laundry – an advantage both to the environment and to your energy bill.

Instead, intensied wash action and water optimisation ensure great

wash results in the same average time of a standard cycle.

For the best washing results we recommend the usage of a liquid

detergent.

Start Delay

To set the selected programme to start at a later time, press the button to

set the desired delay time. The

symbol lights on the display when this

function is enabled. To cancel the delayed start, press the button again

until the value “0” is shown on the display.

Temperature

Each wash cycle has a pre-dened temperature. To modify the

temperature, press the “Temp.” button. The value will appear on the

display.

Spin

Each wash cycle has a pre-dened spin speed. To modify the spin speed,

press the button. The value will appear on the display.“Spin Speed”

Setting the drying cycle

The rst time the button “ ” is pressed, the machine will Drying Settings

automatically select the maximum drying cycle which is compatible with

the selected wash cycle. Subsequent presses will decrease the drying level

and then the drying time, until the cycle is excluded completely (“OFF”).

Drying may be set as follows:

A- Based on the desired laundry dryness level:

Cupboard : suitable for laundry which can be put back in a cupboard

without being ironed.

Hanger : ideal for clothes which do not need to be dried fully.

Iron : suitable for clothes which will need ironing afterwards. the

remaining dampness softens creases, making them easier to remove.

B - Based on a set time period: between 210 and 30 minutes.

If your laundry load to be washed and dried is much greater than the

maximum stated load (see adjacent table of wash cycles), perform the

wash cycle, and when the cycle is complete, divide the garments into

groups and put some of them back in the drum. At this point, follow the

instructions provided for a “Drying only” cycle. Repeat this procedure for

the remainder of the load. Note: a cooling-down period is always added to

the end of each drying cycle.

Drying only

Press button “Dry only” to perform the drying-only cycle. After selecting

the desired cycle (compatible with the type of garments), press button

“Dry only” to exclude the washing phase and start the drying phase at the

maximum level for the selected cycle. The drying level or time may be set

and changed by pressing the drying button “Drying Settings”.

KEY LOCK

to lock the control panel, press and hold the button for “Dry only”

approximately 3 seconds. the symbol lights on the display to indicate

that the control panel is locked (with the exception of the button). This

prevents unintentional changes to programmes, especially with children

near the machine.

If any attempt is made to use the control panel, the symbol ashes on

the display.

To unlock the control panel, press and hold the button “Dry only” for

approximately 3 seconds.

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

Follow the dosage recommendation / additives

It optimizes the cleaning result, it avoids irritating residues of surplus

detergent in your laundry and it saves money by avoiding waste of surplus

detergent

Use low temperature and longer duration

The most ecient programmes in terms of energy consumption are

generally those that perform at lower temperatures and longer duration.

Observe the load sizes

Load your washing machine up to the capacity indicated in the

“PROGRAMME CHART” table to save water and energy.

Noise and remaining moisture content

They are inuenced by the spinning speed: the higher the spinning speed

in the spinning phase, the higher the noise and the lower the remaining

moisture content.

CARE AND MAINTENANCE

Before performing cleaning and maintenance, switch the washing machine

o and disconnect it from the mains power. Do not use ammable liquids to

clean the washing machine. Clean and maintain your washer - dryer

periodically (at least 4 times per year).

Disconnect the water and power supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washing machine and help to prevent leaks.

Unplug the washing machine when cleaning it and during all

maintenance work.

Clean the washing machine

The outer parts and rubber components of the appliance can be cleaned

using a soft cloth soaked in lukewarm soapy water. Do not use solvents or

abrasives.

Clean the detergent dispenser drawer

Wash it under running water; this operation should be repeated

frequently.

Care for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant

odours from forming.

Cleaning the water lter / draining residual water

Switch o and unplug the washing machine, take out the kitchen

plinth before cleaning the water lter or draining residual water.

The kitchen plinth must be mounted back all the time once the cleaning

operation is over.

If you used a hot wash programme, wait until the water has cooled

down before draining any water. Clean the water lter regularly, to

avoid that the water cannot drain after the wash due to obstruction of

the lter. If the water cannot drain, the display indicates that the water

lter may be clogged.

1 . Place a container close to the pump to collect any spillage.

2 . Remove, pulling it out, the “emergency drain hose” from the

base of the washing machine .

Remove the stopper of the “emergency drain hose” at the end of the

hose and let the water ow into the container.

3 . Turn the exhaust lter handle and pull it out of the housing .

When the container of plinth is full with water, plug the stopper to

the hose end, and reinsert the small hose in the washing machine’s

base . After, empty the container .

Afterwards rmly close the emergency drain hose with the stopper .

4. Remove lter: Lay a cotton cloth beneath the water lter, which

can absorb a small amount of rest water . Then remove the water

lter by turning it out anticlockwise .

5 . Clean the water lter: remove residues in the lter and clean it

under running water .

6 . Insert the water lter: Reinsert the water lter again by turning

it in clockwise direction . Make sure to turn it in as far as it goes; the

lter handle must be in vertical position . To test water tightness

of the water lter, you can pour about 1 liter of water into the

detergent dispenser .

Then reinstall the kitchen plinth.

Check the water inlet hose

Check the water inlet hose at least once a year. If it is cracked or broken, it

must be replaced: during wash cycles, the high pressure of the water

could suddenly split the hose open.

! Never use hoses that have already been used.

LOAD BALANCING SYSTEM

Before every spin cycle, to avoid excessive vibrations before every spin and

to distribute the load in a uniform manner, the drum rotates continuously

at a speed which is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly, the machine

spins at a reduced spin speed. If the load is excessively unbalanced, the

washing machine performs the distribution process instead of spinning. To

encourage improved load distribution and balance, we recommend small

and large garments are mixed in the load.

TRANSPORT AND HANDLING

Do not lift the washer-dryer by gripping it from the upper section.

Unplug the appliance and close the water tap. Check that the door and

detergent dispenser drawer are tightly closed. Detach the lling hose

from the water tap then detach the drain hose. Empty all the water

remaining in the hoses and secure the latter so that they do not get

damaged during transport. Apply the transport bolts back on. Repeat, in

reverse order, the transport bolt removal procedure described in the

“Installation instructions”.

Specyfikacje produktu

Marka:	Hotpoint
Kategoria:	pralka
Model:	BI WDHG 961484 UK

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint BI WDHG 961484 UK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje pralka Hotpoint

Hotpoint NSWM 963C W UK Instrukcja

14 Października 2024

Hotpoint NBT 1048 WD A IT Instrukcja

9 Października 2024

Hotpoint NBT 108 BLACK IT Instrukcja

9 Października 2024

Hotpoint NG 847 WM A IT Instrukcja

8 Października 2024

Hotpoint NR 748G WS A IT Instrukcja

8 Października 2024

Hotpoint VLXR1020DWO Instrukcja

8 Października 2024

Hotpoint HDA3420ZBB Instrukcja

8 Października 2024

Hotpoint HDA3600NBB Instrukcja

6 Października 2024

Hotpoint NM11 946 BC A UK Instrukcja

6 Października 2024

Hotpoint NM10 944 GS UK Instrukcja

6 Października 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Candy CS 15102D3-80 Instrukcja

15 Października 2024

GE GSD3715FAA Instrukcja

15 Października 2024

Siemens iQ700 WI14W540EU Instrukcja

15 Października 2024

LG WTP22BK Instrukcja

15 Października 2024

Freggia WTIE148 Instrukcja

15 Października 2024

Freggia WISE126R Instrukcja

15 Października 2024

Freggia WISE126B Instrukcja

15 Października 2024

Freggia WISE126 Instrukcja

15 Października 2024

Freggia WISA105 Instrukcja

15 Października 2024

Freggia WISA106 Instrukcja

15 Października 2024