Instrukcja obsługi Hotpoint AQD1171D 697ID EU/A

Hotpoint pralka AQD1171D 697ID EU/A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hotpoint AQD1171D 697ID EU/A (84 stron) w kategorii pralka. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/84
GB
1
English,1
! This symbol reminds you to read this
instruction manual.
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser drawer
Caring for your appliance drum
Cleaning the pump
Checking the water inlet hose
Precautions and advice, 5
General safety
Disposal
Opening the porthole door manually
Description of the machine, 6-7
Touch control panel
How to run a wash cycle or a drying
cycle, 8
Wash cycles and options, 9
Table of wash cycles
Wash options
Detergents and laundry, 10
Detergent
Preparing the laundry
Washing recommendations
Load balancing system
Trouble shooting, 11
Assistance, 12
GB
WASHER-DRYER
AQUALTIS
AQD1171D 697ID
Instructions for
installation and use
Italiano,13
IT DE
Deutsch,25
SV
Svenska,37
FI
Dansk,61
DK
Norsk,73
NO
Suomi,49
GB
2
Installation
! This instruction manual should be kept in a
safe place for future reference. If the Washer-
dryer is sold, given away or moved, please
ensure the manual is kept with the machine,
so that the new owner may benefit from the
advice contained within it.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
! Inside the pack containing this manual, you
will also find the guarantee and all the details
necessary for installation.
Unpacking and levelling
Unpacking
1. Once you have removed all the packaging
from the Washer-dryer, make sure it has not
been damaged during transportation.
If it has been damaged, contact the retailer
and do not proceed any further with the
installation process.
2. Remove the 4
protective screws
(used during
transportation) and
the corresponding
spacer, located on
the rear part of the
appliance ( ). see figure
3. Close off the holes using the plastic plugs
supplied in the pack.
4. Keep all the parts in a safe place; they will
be needed again if the Washer-dryer is moved
to another location, to prevent the inside of the
appliance being damaged.
! Packaging materials should not be used as
toys for children.
Levelling
1. Place the Washer-
dryer on a flat sturdy
floor, without resting
it up against walls or
cabinets.
2. If the floor is
uneven, the front feet
of the machine may
be adjusted until it
reaches a horizontal
position (the angle of
inclination must not exceed 2 degrees).
! If the appliance is levelled correctly, it will
be more stable and much less likely to cause
vibrations and noise while it is operating,
particularly during the spin cycle.
! If it is placed on carpet or a rug, adjust the
feet in such a way as to allow a sufficient
ventilation space underneath the Washer-dryer.
Connecting the electricity and
water supplies
Connecting the water inlet hose
! Before connecting the inlet hose to the water
supply, run the water until it is perfectly clear.
1. Connect the inlet
hose to the machine
by screwing it onto
the cold water inlet of
the appliance, which
is situated on the top
right-hand side of
the rear part of the
appliance . (see figure)
2. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical data table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand or old inlet hoses;
use the products supplied with the machine.
GB
3
Connecting the drain hose
Connect the drain
hose to drain duct
piping or a wall drain
located between 65
and 100 cm above
the floor, making sure
it is not bent at all.
Alternatively, place
the drain hose
over the edge of
a washbasin or
bathtub, by fastening
the guide (which
can be purchased
at the technical
assistance centre) to
the tap (see figure).
The free end of the
hose should not be underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthemaximum
power load of the appliance as indicated in
the Technical data table (see opposite);
• thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
• thesocketiscompatiblewiththeplugofthe
appliance. If this is not the case, have the
socket or the plug replaced.
! The machine must not be installed outdoors,
even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! The mains socket must remain within
easy reach after the Washer-dryer has been
installed.
! Do not use extension cords or multiple
sockets.
! The cable should not be bent or compressed.
! The power supply cable and plug must only
be replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these regulations
are not respected.
65 - 100 cm
Technical data
Model AQD1171D 697ID
Dimensions
width 59.5 cm
height 85 cm
depth 64.5 cm
Capacity
from 1 to 11 kg for the wash
programme
from 1 to 7 kg for the drying
programme
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 71 litres
Spin speed up to 1600 rotations per
minute
Energy ra-
ted
programmes
according to
regulation
EN 50229
Wash: programme
60°/40°
; tem-
perature 60°C; using a load
of 11 kg.
Drying: the major load (7kg)
must be dried by selecting
the “EXTRA” dryness level;
the remainder of the load
must be dried by selecting
the “EXTRA” dryness level,
the load must consist of 3
sheets and 7 pillowcases.
This appliance conforms to
the following EC Directives:
- EMC 2014/30/EU (Electro-
magnetic Compatibility)
- LVD 2014/35/EU (Low
Voltage)
- 2012/19/EU - (WEEE)

Specyfikacje produktu

Marka: Hotpoint
Kategoria: pralka
Model: AQD1171D 697ID EU/A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hotpoint AQD1171D 697ID EU/A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje pralka Hotpoint

Hotpoint

Hotpoint NSWM 963C W UK Instrukcja

14 Października 2024
Hotpoint

Hotpoint NBT 1048 WD A IT Instrukcja

9 Października 2024
Hotpoint

Hotpoint NBT 108 BLACK IT Instrukcja

9 Października 2024
Hotpoint

Hotpoint NG 847 WM A IT Instrukcja

8 Października 2024
Hotpoint

Hotpoint NR 748G WS A IT Instrukcja

8 Października 2024
Hotpoint

Hotpoint VLXR1020DWO Instrukcja

8 Października 2024
Hotpoint

Hotpoint HDA3420ZBB Instrukcja

8 Października 2024
Hotpoint

Hotpoint HDA3600NBB Instrukcja

6 Października 2024
Hotpoint

Hotpoint NM11 946 BC A UK Instrukcja

6 Października 2024
Hotpoint

Hotpoint NM10 944 GS UK Instrukcja

6 Października 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Candy

Candy CS 15102D3-80 Instrukcja

15 Października 2024
GE

GE GSD3715FAA Instrukcja

15 Października 2024
Siemens

Siemens iQ700 WI14W540EU Instrukcja

15 Października 2024
LG

LG WTP22BK Instrukcja

15 Października 2024
Freggia

Freggia WTIE148 Instrukcja

15 Października 2024
Freggia

Freggia WISE126R Instrukcja

15 Października 2024
Freggia

Freggia WISE126B Instrukcja

15 Października 2024
Freggia

Freggia WISE126 Instrukcja

15 Października 2024
Freggia

Freggia WISA105 Instrukcja

15 Października 2024
Freggia

Freggia WISA106 Instrukcja

15 Października 2024