Instrukcja obsługi Honeywell Performance H4W8PR2

Honeywell Kamera monitorująca Performance H4W8PR2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell Performance H4W8PR2 (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
H4W8PR2 WDR 8 MP IR Rugged Dome Camera
Quick Installation Guide
Thank you for purchasing a Honeywell Performance Series
IP camera. Follow the instructions in this guide to install
and log in to your camera. For instructions on configuring
the camera, refer to the user guide on the CD that came
with your camera. If you require additional assistance, call
the number listed for your region on the back cover.
Warnings and Cautions
WARNING
To ensure compliance with electrical safety standards, this product is
intended for use with a Listed Power Adapter marked “Limited Power
Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,
TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed
Information Technology Equipment meeting IEEE 802.3af PoE standard.
CAUTION
The Ethernet connection is not intended to be connected to exposed
(outside plant) networks. Do not connect two power sources to the camera at
the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam.
Important Safeguards
•
Read and keep these instructions
•
Confirm the installation surface can support at least three times the weight of the camera.
•
Do not apply power to the camera before completing installation.
•
Do not aim the camera toward a bright light source for extended periods to prevent damage to
the imager.
•
Avoid operating the unit under or close to unstable light sources (may cause flickering), or close
to fluorescent lamps or objects reflecting light.
•
Do not touch the camera lens.
•
Do not drop the camera or subject it to physical shock.
•
Do not use a strong or abrasive detergent when cleaning the camera.
•
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where
the operating temperature is outside the recommended range of - (-22°F to 140°F 30°C to
60°C).
Before You Begin
Before you begin, check that you have received all the parts listed below. If any parts are
missing or damaged, contact your dealer immediately.
•
Camera
•
Installation CD
•
Quick installation guide
•
Allen key - (L wrench)
•
Self-tapping screws (×4)
•
Plastic anchors (×4)
•
Mounting template
CAUTION Installation and servicing should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain your
warranty.
Mounting surface
Mounting template
Anchors
Camera assembly
Self-tapping screws
Dome cover
Locking screw
Allen key
Preparing the Mounting Surface
1.
Apply the mounting template to the mounting surface.
2.
Using the mounting template as a guide, drill three pilot holes in the mounting surface,
then hammer the supplied anchors into the holes.
3.
Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.
CAUTION
THIS SYMBOL INDICATES THAT
DANGE OUSR VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CA : TUTION O REDUCE THE RISK OF ELECTRIC
SHOCK, DO N T REM THE CO OVE OVER.
NO USER-SERVICEABLE PAR .TS INSIDE
REFER SER TO QUVICING ALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
RISK OF ELECTRIC
SHOCK
DO N T OPENO
© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.
Mounting and Aiming the Camera
1.
Remove the dome cover from the camera assembly using the supplied Allen key.
2.
If you using microSD with are a card the install it before continuing. See below for camera,
details.
slide metal
shell to
unlock
2. Open
metal
shell.
3. Insert microSD
card.
4. Close metal
shell and
slide to lock
position.
3.
Connect the cable to the RJ 45 port on theEthernet - camera.
4.
If the other end of Ethernet cable is connected to a PoE (Powerthe not -over Ethernet) -
switch or NVR, connect the power connector of the camera to a 12 VDC power source.
5.
Fix the camera assembly to the mounting surface using the supplied screws.
6.
Aim screw the camera lens in the desired direction, then tighten the s on the camera
assembly.
7.
Reattach the dome cover.
Logging On to the Camera
If the camera is connected to the PoE port of a Honeywell Embedded NVR, it can be configured
using the NVR.
To log on remotely from a PC, install the Honeywell Config Tool from the software and
documentation CD, find the camera on the network, and then open the web browser with the
Honeywell Config Tool. The default user name is admin (case sensitive) the- and default password
is . 1234
Note
• Only Internet Explorer 11 (or later) is supported.
• IP address of the device is assigned automatically by server. If the DHCP server DHCP
is not available, the device will acquire as the default IP 192.168.1.108 address.
Adjusting the Zoom and Focus Settings
After you have logged on to the camera, go to Setup > Camera > Conditions > Zoom and
Focus to fine tune the camera’s zoom and focus settings.-
Recommended Recorders
HEN*4
-8/16/32/64 channel Focus 4K NVRs (H.264 and H.265)
HEN*3 - ) 4/8/16/32 channel Performance Series NVRs (H.264 and H.265
Regulatory Statements
FCC Compliance
This equipment has been tested and found to comply with the for a limits Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his
own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES- 003.
Manufacturer’s Declaration of Conformance
North America The equipment supplied with this guide conforms to UL 60950 1 and CSA C22.2 No. 60950- -1.
Europe The manufacturer declares that the equipment supplied is compliant with the European Parliament
and Council Directive on the of restriction the use of certain hazardous substances in electrical and electronic
equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and the essential of requirements
the EMC directive (2014/30/EU), conforming to the requirements of standards EN 55032 for emissions, EN
50130-4 for immunity, and EN -1 for 62368 electrical equipment safety.
CAUTION This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
WEEE (Waste Electrical and Electronic Equipment)
Correct disposal of this product (applicable in the European Union and other European countries with
separate collection systems).This product should be disposed of, at the end of its useful life, as per
applicable local laws, regulations, and procedures.
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY, 40299, USA
www.honeywell.com/security
+1 800 323 4576
(North America only)
Aston Fields Road, Whitehouse Industrial
Estate Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
+1 44 (0) 1928 754 028
(Europe only)
Building #1, 555 Huanke Road, Zhang
Jiang Hi- Tech Park
Pudong New Area, Shanghai, 201203,
China www.asia.security.honeywell.com
+400 840 2233
(Asia Pacific only)
Document 800-24595 09– – Rev A /2018

Specyfikacje produktu

Marka: Honeywell
Kategoria: Kamera monitorująca
Model: Performance H4W8PR2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Honeywell Performance H4W8PR2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Honeywell

Honeywell

Honeywell Performance H4W8PER2V Instrukcja

21 Grudnia 2024
Honeywell

Honeywell HC35WE5R3 Instrukcja

21 Grudnia 2024
Honeywell

Honeywell HD3C Instrukcja

23 Września 2024
Honeywell

Honeywell Equip HCD5WIH Instrukcja

19 Września 2024
Honeywell

Honeywell HDZ30A Instrukcja

14 Września 2024
Honeywell

Honeywell Performance HD31H Instrukcja

13 Września 2024
Honeywell

Honeywell HD50 Instrukcja

11 Września 2024
Honeywell

Honeywell Equip HDZ30 Instrukcja

10 Września 2024
Honeywell

Honeywell Performance HBW8PR2 Instrukcja

10 Września 2024
Honeywell

Honeywell HDZ36AEX Instrukcja

10 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025
Toshiba

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025
AVerMedia

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025
Digitus

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025
Speco Technologies

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025
ZKTeco

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025