Instrukcja obsługi Honeywell H4D3PRV3

Honeywell Kamera monitorująca H4D3PRV3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell H4D3PRV3 (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

H4D3PRV3 True Day/Night Rugged Indoor/Outdoor

IR Minidome IP Camera Regulatory Statements

Information to the User: This has equipment been and tested found to comply with the limits afor

Class B digital device, pursuant to part 15 of the Rules. FCC These limits are designed to provide

reasonable against protection harmful interference a in residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that a particular interference will not occur in installation.

Quick Installation Guide

Document -800 21230V1— A – Rev 10/2015

Thank you for a camera. purchasing H4D3PRV3

Follow the

instructions in this guide and to install

set up your camera. For instructions on

configuring the

camera, refer to the Performance

Series IP

Cameras User Guide on the software

and

documentation CD that came with your

camera. If

you require additional assistance,

please call the

number shown below.

If this equipment does cause harmful interference to radio be or television reception, which can

determined by turning the equipment is and off on, the user encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the the separation between equipment and receiver.

Connect the equipment into an outlet a that on circuit different from to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Cautions and Warnings

•

Note Changes or modifications not expressly approved by party the responsible for compliance

could void the user’s authority to operate the equipment.

This B Class digital apparatus complies Canadian with ICES- 003.

Cet appareil numérique de la B à Classe est conforme la - Canada. norme NMB 003 du

Important Safeguards

WARNING

•

Read and keep these instructions.

Do not aim the camera toward a bright light source for extended periods to prevent damage to

the imager. Avoid operating the unit under or close to unstable light sources (may cause

flickering), or close to fluorescent lamps or objects reflecting light.

Do not touch the camera lens.

Do not drop the camera or subject it to physical shock.

Do not use a strong or abrasive detergent when cleaning the camera.

Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the

operating temperature is outside the recommended range of - 4°F to 140°F (– 20°C to 60°C).

To ensure compliance with electrical safety standards this product is

intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,

on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over

Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE

802.3af PoE standard. •

•

The Ethernet connection is not intended to be connected to exposed (outside plant)

networks. Do not connect two power sources to the camera at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam. Note

Do not apply power to the completing installation. camera before

Note

Confirm the installation surface can support at least three times the weight of the camera.

Document - – A – 1800 21230V1 Rev 10/2015

H4D3PRV3 True Day/Night Rugged Indoor/Outdoor IR Minidome IP Camera

Before You Begin

Before you begin, check that you have received all of the parts listed If any parts are below. missing

or your damaged, contact dealer immediately.

•

Camera

Documentation CD

Quick install guide

Allen key (L- wrench)

•

Self- 3)tapping screws (×

Plastic wall anchors 3)(×

Mounting template

Mounting the Camera

1. Use the to p su plied Allen key o t do co f the ra a ly rem ve he me ver rom came ssemb and set it

aside.

2. Connect the camera with the Ethernet cable and the power cable.

a. Connect one end of the Ethernet cable to the RJ- 45 port on the camera.

b. If the other end of the Ethernet cable is NOT connected to a PoE

(Power- -over Ethernet) switch or NVR, connect the power connector of

the camera to a 12 V DC power source.

3. Attach the camera assembly to the mounting surface using the supplied screws.

Required tools:

•

A Philips screwdriver

A drill with an appropriately- sized drill bit for pre- drilling holes for the screw anchors.

Installation and servicing should be performed only by qualified

and experienced technicians to conform to all local codes and to maintain your

warranty.

Aiming the Camera

Aim the camera lens in a desired direction.

2. Tighten the adjustment screws to secure the camera lens in place.

3. Attach the dome cover to the camera and remove the protective film from the bubble.

Preparing the Mounting Surface

1. Inspect the site where you want to install the camera. The mounting surface must be

flat and capable of supporting at least three times the weight of the camera.

2. Remove the backing from the mounting template sticker and affix the sticker to the

mounting surface.

Note If you are using the side exit for the cable, no te the orientation of the cab le exit no tch.

In out oor onsd ins l ital at the no r to t fr i tch should point downwa ds prevent wa er om enter ng

the ca i mera hous ng.

Document -800 21230 10/2015V1 – – Rev A

© 5 this publication 201 Honeywell International Inc. All rights reserved. No part of may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,

Honeywell cannot assume responsibility for any consequences the resulting from use thereof. The information Revisions editions contained herein is subject to change without notice. or new to this publication may be issued to incorporate such changes.