Instrukcja obsługi HK Audio Polar 10

HK Audio głośnik Polar 10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla HK Audio Polar 10 (48 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/48

Manual 1.1

POLAR 10

• English • Français• Deutsch • Italiano • Español

Important Safety Instructions!

Read before connecting!

This product has been built by the manufacturer in accordance with

IEC 62368-1 and left the factory in safe working order. To maintain

this condition and ensure non-risk operation, the user must follow the

advice and warning comments found in the operating instructions. If

this product shall be used in vehicles, ships or aircraft or at altitudes

exceeding 2000 m above sea level, take care of the relevant safety

regulations which may exceed the IEC 62368-1 requirements.

WARNING: To prevent the risk of fire and shock hazard, do not

expose this appliance to moisture or rain. Do not open case – no user

serviceable parts inside. Refer service to qualified service personnel.

This symbol, wherever it appears, alerts you to the presence

of uninsulated dangerous voltage inside the enclosure – voltage that

may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to the presence

of externally accessible hazardous voltage. External wiring connected

to any terminal marked with this symbol must be a "ready made

cable" complying with the manufacturers recommendations, or must

be a wiring installed by instructed persons only.

This symbol, wherever it appears, alerts you to important

operating and maintenance instructions in the accompanying

literature. Read the manual.

This symbol, wherever it appears, tells you: Take care! Hot

surface! To prevent burns you must not touch.

All electrical and electronic products including batteries

should be disposed of separately from the municipal waste stream via

designated collection facilities appointed by the government or the

local authorities.

Read these instructions. Keep these instructions. Follow all

warnings and instructions marked on the product and in this manual.

• Do not use this product near water. Do not place the product near

water, baths, wash basins, kitchen sinks, wet areas, swimming pools

or damp rooms.

• Do not place objects containing liquid on the product – vases,

glasses, bottles etc.

• Clean only with dry cloth.

• Do not remove any covers or sections of the housing.

• The set operating voltage of the product must match the local mains

supply voltage. If you are not sure of the type of power available

consult your dealer or local power company.

• Before connecting the device, please ensure that the mains supply

you are using is equipped with adequate protection against short

circuiting and grounding faults when the device is plugged in.

• To reduce the risk of electrical shock, the grounding of this product

must be maintained. Use only the power supply cord provided with

this product, and maintain the function of the center (grounding)

pin of the mains connection at any time. Make sure the mains outlet

used provides a proper protective ground connection.

• Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit

from the device! Power supply cords should always be handled

carefully. Periodically check cords for cuts or sign of stress, especially

at the plug and the point where the cord exits the device.

• Never use a damaged power cord.

• Unplug this product during lightning storms or when unused for long

periods of time.

• This product can be fully disconnected from mains only by pulling

the mains plug at the unit or the wall socket. The product must be

placed in such a way at any time, that disconnecting from mains is

easily possible.

• Fuses are to be replaced exclusively by qualified personnel, and then

only with fuses of the proper type and rating.

• Refer all servicing to qualified service personnel. Servicing is

required when the unit has been damaged in any way, such as:

- When the power cord or plug is damaged or frayed.

- If liquid has been spilled or objects have fallen into the product.

- If the product has been exposed to rain or moisture.

- If the product does not operate normally when the operating

instructions are followed.

- If the product has been dropped or the cabinet has been damaged.

• Do not connect external speakers to this product with an impedance

lower than the rated impedance given on the product or in this

manual. Use only cables with sufficient cross section according to

the local safety regulations.

• Keep away from direct sunlight.

• Do not install near heat sources such as radiators, heat registers,

stoves or other devices that produce heat.

• This apparatus is for moderate climates areas use, not suitable for

use in tropical climates countries.

• Do not block any ventilation openings. Install in accordance with

manufacturer’s instructions. This product must not be placed in

a built-in installation such as a rack unless proper ventilation is

provided.

• Always allow a cold device to warm up to ambient temperature,

when being moved into a room. Condensation can form inside it and

damage the product, when being used without warming up.

• Do not place naked flame sources, such as lighted candles on the

product.

• The device must be positioned at least 20 cm/8" away from walls.

• Use only with the cart, stand, tripod, bracket or table specified by

the manufacturer or sold with the product. When a cart is used, use

caution when moving the cart/product combination to avoid injury

from tip-over.

• Use only accessories recommended by the manufacturer, this applies

for all kind of accessories, for example protective covers, transport

bags, stands, wall or ceiling mounting equipment. In case of

attaching any kind of accessories to the product, always follow the

instructions for use, provided by the manufacturer. Never use fixing

points on the product other than specified by the manufacturer.

• This appliance is NOT suitable to be used by any person or persons

(including children) with limited physical, sensorical or mental

ability, or by persons with insufficient experience and/or knowledge

to operate such an appliance. Children under 4 years of age must be

kept away from this appliance at all times.

• Never push objects of any kind into this product through cabinet

slots as they may touch dangerous voltage points or short out parts

that could result in risk of fire or electric shock.

• This product is capable of delivering sound pressure levels in excess

of 90 dB, which may cause permanent hearing damage! Exposure

to extremely high noise levels may cause a permanent hearing loss.

Wear hearing protection if continously exposed to such high levels.

• The manufacturer only guarantees the safety, reliability and

efficiency of this product if:

- Assembly, extension, re-adjustment, modifications or repairs are

carried out by the manufacturer or by persons authorized to do so.

- The electrical installation of the relevant area complies with the

requirements of IEC (ANSI) specifications.

- The unit is used in accordance with the operating instructions.

• This product is optimized for use with music and speech signals.

Using this product with sine wave, square wave or other kind of

measuring signals at higher level may lead to severe damage of the

product.

General Notes on Safety for Loudspeaker

Systems

Mounting systems may only be used for those loudspeaker

systems authorized by the manufacturer and only with the mounting

accessories specified by the manufacturer in the installation

instructions. Read and heed the manufacturer’s installation

instructions. The indicated load-bearing capacity cannot be guaranteed

and the manufacturer will not be liable for damages in the event of

improper installation or the use of unauthorized mounting accessories.

The system’s load-bearing capacity cannot be guaranteed and

the manufacturer will not be liable for damages in the event that

loudspeakers, mounting accessories, and connecting and attaching

components are modified in any way.

Components affecting safety may only be repaired by the manufacturer

or authorized agents, otherwise the operating permit will be voided.

Installation may be performed qualified personnel only, and

then only at pick-points with sufficient load-carrying capacity and

in compliance with local building regulations. Use only the mounting

hardware specified by the manufacturer in the installation instructions

(screws, anchors, etc.). Take all the precautions necessary to ensure

bolted connections and other threaded locking devices will not loosen.

Fixed and portable installations (in this case, speakers and

mounting accessories) must be secured by two independent safeties to

prevent them from falling. Safeties must be able to catch accessories

or parts that are loose or may become loose. Ensure compliance with

the given national regulations when using connecting, attaching,

and rigging devices. Factor potential dynamic forces (jerk) into the

equation when determining the proper size and load-bearing capacity

of safeties.

Be sure to observe speaker stands’ maximum load-bearing

capacity. Note that for reasons of design and construction, most

speaker stands are approved to bear centric loads only; that is, the

speakers’ mass has to be precisely centered and balanced. Ensure

speaker stands are set up stably and securely. Take appropriate added

measures to secure speaker stands, for example when:

- the floor or ground surface does not provide a stable, secure base.

- they are extended to heights that impede stability.

- high wind pressure may be expected.

- there is the risk that they may be knocked over by people.

Special measures may become necessary as precautions against

unsafe audience behavior. Do not set up speaker stands in evacuation

routes and emergency exits. Ensure corridors are wide enough and put

proper barriers and markings in place when setting speaker stands up

in passageways. Mounting and dismounting are especially hazardous

tasks. Use aids suitable for this purpose. Observe the given national

regulations when doing so.

Wear proper protection (in particular, a helmet,

gloves, and safety shoes) and use only suitable means of ascent

(ladders, scaffolds, etc.) during installation. Compliance with this

requirement is the sole responsibility of the company performing the

installation.

WARNING! After installation, inspect the system comprised

of the mounting fixtures and loudspeakers to ensure it is properly

secured.

The operator of loudspeaker systems (fixed or portable) must

regularly inspect or task a third party to regularly inspect all system

components in accordance with the given country’s regulations and

have possible defects repaired immediately.

We also strongly recommend maintaining a logbook or the like to

document all inspections.

Also be sure to provide sufficient safety margins for the rigging points

used for flown systems. Observe the given national regulations when

doing so.

Professional loudspeaker systems can produce harmful

volume levels. Even prolonged exposure to seemingly harmless levels

(starting at about 95 dBA SPL) can cause permanent hearing damage!

Therefore we recommend that everyone who is exposed to high volume

levels produced by loudspeaker systems wears professional hearing

protection (earplugs or earmuffs).

Manufacturer: Stamer Musikanlagen GmbH, Magdeburger Str. 8, 66606

St. Wendel, Germany

Version 2.8 08/2019

POLAR 10 1.1

Welcome to the HK Audio family!

Thank you for choosing a brand-name product made by our company. It

was engineered and built with the greatest care so it will serve you well for

many tomorrows to come.

Even if your experience with sound systems runs deep, some things

about this product are sure to be new to you. This is why we ask that you do

not set this manual aside without reading it ﬁ rst. Be sure to keep it in a

safe place for later reference.

Here's wishing you the best sound at every occasion!

Your HK Audio team

Strong electromagnetic interference or electrostatic discharge

may prevent the product from functioning normally. If this happens, the

product may be returned to normal operation by powering o and on

again. Should this not result in the product functioning normally again,

please move the product away from the source of disturbance and try

again.

Warranty

Use the convenient online registration option at www.hkaudio.com.

http://warranty.hkaudio.com

The registration is only valid if the device is registered within 30 days of

the date of purchase.

HK Audio

Technischer Service

Postfach 1509

66595 St. Wendel, Germany

Fax: +49 6851 905 100

1 General Information

1.1 Unpacking and Inventory

Please remove the entire system from the cartons and make sure you have

received all its component parts. POLAR comes in two cartons and consists

of a subwoofer, a columnar mid/high unit and a spacer. The mains cable is

also included.

1.2 The Components

The Subwoofer

The powered subwoofer houses the bass woofer, the system’s electronic

components and the power ampliﬁ ers. On the top panel is a signal-carrying,

plug-in port serving to connect the column’s elements and a carrying

handle. Another handy grip routed into the front of the bottom panel lets

you comfortably carry the subwoofer with one or two hands. The integrated

control panel with the display, control features and connectors slopes

slightly toward the rear to protect the controls against damage. The bass

reﬂ ex ports are located at the bottom of the

front panel. The power o /on switch and

mains socket are on the rear panel.

The Column

• The column consists of a mid/high unit and

a spacer.

• The spacer plugs into a signal-carrying

socket/coupler on the subwoofer. The mid/

high unit plugs into the spacer using the

same type of connector.

• This coupler provides a mechanical and

electrical connection between the mid/high

unit and spacer, so you do not need speaker

cables to connect the two.

1.3 Setting up the System

Connecting Components

• Place the subwoofer on a level, stable

surface.

• Connect the spacer and the mid/high unit to the subwoofer as described

in section 1.2 above.

• Make sure the components are ﬁ rmly seated and connected to one

another.

• Plug the power cord into the rear mains power socket.

• English • Deutsch

POLAR 10

Mid/high

unit

Spacer

Subwoofer

• Français • Italiano • Español

Specyfikacje produktu

Marka:	HK Audio
Kategoria:	głośnik
Model:	Polar 10
Kolor produktu:	Czarny
Materiał obudowy:	Kopolimer akrylonitrylo-butadieno-styrenowy (ABS)
Wysokość produktu:	2130 mm
Waga produktu:	26900 g
Technologia łączności:	Przewodowy i Bezprzewodowy
Bluetooth:	Tak
Wersja Bluetooth:	5.0
Moc wyjściowa (RMS):	2000 W
Kanały wyjścia audio:	- kan.
Mikrofon:	Tak
Regulacja głośności:	obrotowy
Wejście liniowe:	Tak
Wejście AUX:	Tak
Zasięg częstotliwości:	38 - 20000 Hz
Rozmieszczenie głośników:	Podłoga
Ilość przetworników:	8
Głośnik wysokotonowy:	Tak
Liczba głośników wysokotonowych:	1
Liczba głośników niskotonowych:	1
Średnica głośnika wysokotonowego:	1 "
Średnica głośnika niskotonowego (imperial):	10 "
Średnica sterownika średniego zasięgu (imperial):	3 "
Maksymalny poziom natężenia dźwięku:	126 dB
Liczba głośników średniotonowych:	6