Instrukcja obsługi Hikvision DS-2TD2166-7/V1

Hikvision Kamera monitorująca DS-2TD2166-7/V1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hikvision DS-2TD2166-7/V1 (135 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/135

Network Camera User Manual

User Manual

05094BUD

Thermal Network Bullet Camera

Thermal Network Bullet Camera User Manual

User Manual

Any and all information, including, among others, wordings, pictures, graphs are the

properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries

(hereinafter referred to be "Hikvision"). This user manual (hereinafter referred to be

"the Manual") cannot be reproduced, changed, translated, or distributed, partially or

wholly, by any means, without the prior written permission of Hikvision. Unless

otherwise stipulated, Hikvision does not make any warranties, guarantees or

representations, express or implied, regarding to the Manual.

About this Manual

This Manual is applicable to . Thermal Network Bullet Camera

The Manual includes instructions for using and managing the product. Pictures, charts,

images and all other information hereinafter are for description and explanation only.

The information contained in the Manual is subject to change, without notice, due to

firmware updates or other reasons. Please find the latest version in the company

website ( ). http://overseas.hikvision.com/en/

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision's trademarks and logos are the properties of

Hikvision in various jurisdictions. Other trademarks and logos mentioned below are

the properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE

PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

FIRMWARE, IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND

HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,

Thermal Network Bullet Camera User Manual

FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF

THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,

EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING,

AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS

INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN

CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF

PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL

NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,

PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER

ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET

SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY

TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL

RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT

IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE

LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS

PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE

APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and found to comply with the

limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance

Thermal Network Bullet Camera User Manual

9.2.3 Conguring Dynamic Fire Source Detecon ................................................................... 87

9.2.4 Conguring Fire Source Detecon Shield ....................................................................... 88

9.3 VCA Configuraon .......................................................................................... 90

9.3.1 Conguring Overlay & Capture ....................................................................................... 90

9.3.2 Conguring Camera Calibraon ...................................................................................... 91

9.3.3 Conguring Shield Region ............................................................................................... 92

9.3.4 Conguring Rule ............................................................................................................. 93

9.3.5 Advanced Conguraon . ................................................................................................ 95

9.4 Temperature Measurement ............................................................................ 97

9.4.1 Basic Sengs .................................................................................................................. 97

9.4.2 Advanced Sengs ........................................................................................................... 99

9.4.3 Linkage Method ............................................................................................................ 105

Chapter 10 Storage Settings ........................................................................... 106

10.1 Conguring Record Schedule ........................................................................ 106

10.2 Congure Capture Schedule 109 .........................................................................

10.3 Conguring Net HDD .................................................................................... 111

10.4 Memory Card Detection ............................................................................... 113

10.5 Conguring Lite Storage 115 ...............................................................................

Chapter 11 Playback ...................................................................................... 117

Chapter 12 Picture ........................................................................................119

Appendix ........................................................................................................... 120

Appendix 1 SADP Software Introduction 120...............................................................

Appendix 2 Port Mapping 123......................................................................................

Network Camera User Manual

Chapter 1 System Requirement

Operating System: Microsoft Windows XP SP1 and above version

CPU: 2.0 GHz or higher

RAM: 1G or higher

Display: 1024×768 resolution or higher

Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above

version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above

version.

Network Camera User Manual

Chapter 2 Network Connection

Note:

 You shall acknowledge that the use of the product with Internet access might be

under network security risks. For avoidance of any network attacks and

information leakage, please strengthen your own protection. If the product does

not work properly, please contact with your dealer or the nearest service center.

 To ensure the network security of the network camera, we recommend you to

have the network camera assessed and maintained termly. You can contact us if

you need such service.

Before you start:

 If you want to set the network camera via LAN (Local Area Network), please a

refer to 2.1.

 If you want to set the network camera via WAN (Wide Area Network), please a

refer to 2.2 .

2.1 Setting the Network Camera over the LAN

Purpose:

To view and configure the camera via LAN, you need to connect the network a

camera in the same subnet with your computer, and install the SADP or iVMS-4200

software to search and change the IP of the network camera.

Note: For the detailed introduction of SADP, please refer to Appendix 1.

2.1.1 Wiring over the LAN

The following figures show the two ways of cable connection of network camera a

and computer: a

Purpose:

 To test the network camera, you can directly connect the network camera to the

computer with a network cable as shown in Figure 2-1.

Thermal Network Bullet Camera User Manual

 Refer to Figure 2-2 to set network camera over the LAN via a switch or a router.

Network Cable

Network Camera

Computer

Figure 2-1 Connecting Directly

Network Cable

Network Camera Computer

Figure 2-2 Connecting via a Switch or Router a

2.1.2 Activating the Camera

You are required to activate the camera first by setting a strong password for it before

you can use the camera.

Activation via Web Browser, Activation via SADP, and Activation via Client Software

are all supported.

 Activation via Web Browser

Steps:

1. Power on the camera, and connect the camera to the network.

2. Input the IP address into the address bar of the web browser, and click to Enter

enter the activation interface.

Notes:

 The default IP address of the camera is 192.168.1.64.

 The computer and the camera should belong to the same subnet.

 For the camera enables the DHCP by default, you need to use the SADP software

to search the IP address.

Thermal Network Bullet Camera User Manual

Figure 2-3 Activation via Web Browser

3. Create a password and input the password into the password field.

STRONG PASSWORD RECOMMENDED–We highly recommend you

create a strong password of your own choosing (using a minimum of 8

characters, including at least three of the following categories: upper case letters,

lower case letters, numbers, and special characters) in order to increase the

security of your product. And we recommend you reset your password regularly,

especially in the high security system, resetting the password monthly or weekly

can better protect your product.

4. Confirm the password.

5. Click to save the password and enter the live view interface. OK

 Activation via SADP Software

SADP software is used for detecting the online device, activating the camera, and

resetting the password.

Get the SADP software from the supplied disk or the official website, and install the

SADP according to the prompts. Follow the steps to activate the camera.

Steps:

1. Run the SADP software to search the online devices.

2. Check the device status from the device list, and select the inactive device.

Thermal Network Bullet Camera User Manual

Select inacve device.

Input and conrm

password.

Figure 2-4 SADP Interface

Note:

The SADP software supports activating the camera in batch. Refer to the user manual

of SADP software for details.

3. Create a password and input the password in the password field, and confirm the

password.

STRONG PASSWORD RECOMMENDED– We highly recommend

you create a strong password of your own choosing (using a minimum

of 8 characters, including at least three of the following categories:

upper case letters, lower case letters, numbers, and special characters) in

order to increase the security of your product. And we recommend you

reset your password regularly, especially in the high security system,

resetting the password monthly or weekly can better protect your

product.

Note:

You can enable the Hik-Connect service for the device during activation.

4. Click start activation. Activate to

You can check whether the activation is completed on the popup window. If activation

failed, please make sure that the password meets the requirement and try again.

5. Change the device IP address to the same subnet with your computer by either

modifying the IP address manually or checking the checkbox of Enable DHCP.

Thermal Network Bullet Camera User Manual

Figure 2-5 Modify the IP Address

6. Input the admin password and click to activate your IP address Modify

modification.

The batch IP address modification is supported by the SADP. Refer to the user manual

of SADP for details.

 Activation via Client Software

The client software is versatile video management software for multiple kinds of

devices.

Get the client software from the supplied disk or the official website, and install the

software according to the prompts. Follow the steps to activate the camera.

Steps:

1. Run the client software and the control panel of the software pops up, as shown in

the figure below.

Thermal Network Bullet Camera User Manual

Figure 2-6 Control Panel

2. Click the icon to enter the Device Management interface, as Device Management

shown in the figure below.

Figure 2-7 Device Management Interface

Thermal Network Bullet Camera User Manual

3. Check the device status from the device list, and select an inactive device.

4. Click the button to pop up the Activation interface. Activate

5. Create a password and input the password in the password field, and confirm the

password.

STRONG PASSWORD RECOMMENDED–We highly recommend

you create a strong password of your own choosing (using a minimum of

8 characters, including at least three of the following categories: upper

case letters, lower case letters, numbers, and special characters) in order

to increase the security of your product. We recommend you reset your

password regularly, especially in the high security system, resetting the

password monthly or weekly can better protect your product.

Figure 2-8 Activation Interface (Client Software)

6. Click button to start activation. OK

7. Click the Modify Netinfo button to pop up the Network Parameter Modification

interface, as shown in the figure below.

Thermal Network Bullet Camera User Manual

Figure 2-9 Modifying the Network Parameters

8. Change the device IP address to the same subnet with your computer by either

modifying the IP address manually or checking the checkbox of Enable DHCP.

9. Input the password to activate your IP address modification.

2.2 Setting the Network Camera over the WAN

Purpose:

This section explains how to connect the network camera to the WAN with a static IP

or a dynamic IP.

2.2.1 Static IP Connection

Before you start:

Please apply a static IP from an ISP (Internet Service Provider). With the static IP

address, you can connect the network camera via a router or connect it to the WAN

directly.

 Connecting the network camera via a router

Steps:

1. Connect the network camera to the router.

Thermal Network Bullet Camera User Manual

2. Assign a LAN IP address, the subnet mask and the gateway. Refer to 2.1.2for

detailed IP address configuration of the network camera.

3. Save the static IP in the router.

4. Set port mapping, e.g., 80, 8000, and 554 ports. The steps for port mapping vary

according to the different routers. Please call the router manufacturer for

assistance with port mapping.

Note: Refer to Appendix 2 for detailed information about port mapping.

5. Visit the network camera through a web browser or the client software over the

internet.

Figure 2-10 Accessing the Camera through Router with Static IP

 Connecting the network camera with static IP directly

You can also save the static IP in the camera and directly connect it to the internet

without using a router. Refer to 2.1.2 for detailed IP address configuration of the

network camera.

Figure 2-11 Accessing the Camera with Static IP Directly

2.2.2 Dynamic IP Connection

Before you start:

Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect

the network camera a modem or a router. to

 Connecting the network camera via a router

Steps:

Thermal Network Bullet Camera User Manual

Figure 2-13 Normal Domain Name Resolution

Steps:

1. Apply a domain name from a domain name provider.

2. Configure the DDNS settings in the interface of the network DDNS Settings

camera. Refer to for detailed Section 6.1.2 Configuring DDNS Settings

configuration.

3. Visit the camera via the applied domain name.

 Private Domain Name Resolution

Figure 2-14 Private Domain Name Resolution

Steps:

1. Install and run the IP Server software in a computer with a static IP.

2. Access the network camera through the LAN with web browser or the client a

software.

3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.1.2

Configuring DDNS Settings for detailed configuration.

Thermal Network Bullet Camera User Manual

Figure 3-2 Download and Install Plug- in

Note: You may have to close the web browser to finish the installation of the

plug-in.

6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4

to login.

Note: For detailed instructions of further configuration, please refer to the user

manual of network camera.

3.2 Accessing by Client Software

The product CD contains the iVMS-4200 client software. You can view the live video

and manage the camera with the software.

Follow the installation prompts to install the software. The control panel and live view

interface of iVMS-4200 client software are shown as below.

Thermal Network Bullet Camera User Manual

For IE (Internet Explorer) users, plug-ins webcomponents and quick time are as

selectable. And for Non-IE users, webcomponents, quick time, VLC or MJPEG is

selectable if they are supported by the web browser.

PTZ Control:

Perform panning, tilting and zooming actions of the camera. Control light and the the

wiper (only available for cameras supporting PTZ function).

Preset/Patrol Settings :

Set/call/delete the presets or patrols for PTZ cameras.

4.2 Starting Live View

In the live view window as shown in Figure 4-2, click on the toolbar to start the

live view of the camera.

Figure 4-2 Live View Toolbar

Table 4-1 Descriptions of the Toolbar

Icon

Description

Start/Stop live view.

The window size is 4:3.

The window size is 16:9.

The original widow size.

Self-adaptive window size.

Live view with the main stream.

Live view with the sub stream.

Live view with the third stream.

Click to select the third-party plug-in.

Manually capture the picture.

Manually start/stop recording.

Audio on and adjust volume /Mute.

Turn on/off microphone.

Start/stop digital zoom function.

Note: The icons vary according to the different camera models.

Thermal Network Bullet Camera User Manual

4.3 Recording and Capturing Pictures Manually

In the live view interface, click on the toolbar to capture the live pictures or click

to record the live view. The saving paths of the captured pictures and clips can be

set on the page. To configure remote scheduled recording, Configuration > Local

please refer to . Section 10.1

Note: The captured image will be saved as JPEG file or BMP file your computer. in

4.4 Operating PTZ Control

Note: Certain models do not support the PTZ control. This section only applies to the

camera that supports PTZ control.

Purpose:

In the live view interface, you use the PTZ control buttons to realize pan/tilt/zoom can

control of the camera.

Note: To realize PTZ control, the camera connected to the network must support the

PTZ function or have a pan/tilt unit installed to the camera. Please properly set the

PTZ parameters on RS485 settings page referring to Section 5.2.3.

4.4.1 PTZ Control Panel

On the live view page, click next to the right side of the live view window to show

the PTZ control panel and click to hide . it

Click the direction buttons to control the pan/tilt movements.

Thermal Network Bullet Camera User Manual

Patrol

4.4.2 Setting/Calling a Preset

 Setting a Preset:

1. In the PTZ control panel, select a preset number from the preset list.

Figure 4-4 Setting a Preset

2. Use the PTZ control buttons to move the lens the desired position. to

• Pan the camera to the right or left.

• Tilt the camera up or down.

• Zoom in or out.

• Refocus the lens.

3. Click to finish the setting of the current preset.

4. You can click to delete the preset.

 Calling a Preset:

This feature enables the camera to point to a specified preset scene manually or when

an event takes place.

For the defined preset, you can call it at any time to the desired preset scene.

In the PTZ control panel, select a defined preset from the list and click to call the

preset.

Or you can place the mouse on the presets interface, and call the preset by typing the

preset No. to call the corresponding presets.

Thermal Network Bullet Camera User Manual

Figure 4-5 Calling a Preset

4.4.3 Setting/Calling a Patrol

Note:

No less than 2 presets have to be configured before you set a patrol.

Steps:

1. Click to enter the patrol configuration interface.

2. Select a path No., and click to add the configured presets.

3. Select the preset, and input the patrol duration and patrol speed.

4. Click OK to save the first preset.

5. Follow the steps above to add the other presets.

Figure 4-6 Add Patrol Path

6. Click to save a patrol. OK

7. Click to start the patrol, and click to stop it.

8. (Optional) Click to delete a patrol.

Network Camera User Manual

Chapter 5 Network Camera

Configuration

5.1 Configuring Local Parameters

Purpose:

The local configuration refers to the parameters of the live view, record files and

captured pictures. The record files and captured pictures are the ones you record and

capture using the web browser and thus the saving paths of them are on the PC

running the browser.

Steps:

1. Enter the Local Configuration interface: > . Configuration Local

Figure 5-1 Local Configuration Interface

2. Configure the following settings:

 Live View Parameters: Set the protocol type and live view performance.

 Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.

TCP: Ensures complete delivery of streaming data and better video quality,

yet the real-time transmission will be affected.

UDP: Provides real-time audio and video streams.

Thermal Network Bullet Camera User Manual

HTTP: Allows the same quality as of TCP without setting specific ports for

streaming under some network environments.

MULTICAST: It’s recommended to select MCAST type when using the

Multicast function. For detailed information about Multicast, refer to

Section6.1.1.

 Play Performance: Set the play performance to Shortest Delay or Auto.

 Rules: It refers to the rules on your local browser, select enable or disable to

display or not display the colored marks when the motion detection, face

detection, or intrusion detection is triggered. E.g., enabled as the rules are, and

the face detection is enabled as well, when a face is detected, it will be marked

with a green rectangle on the live view.

 Image Format: Choose the image format for picture capture.

 Record File Settings: Set the saving path of the recorded video files. Valid for the

record files you recorded with the web browser.

 Record File Size: Select the packed size of the manually recorded and

downloaded video files to 256M, 512M or 1G. After the selection, the

maximum record file size is the value you selected.

 Save record files to: Set the saving path for the manually recorded video files.

 Save downloaded files to: Set the saving path for the downloaded video files

in playback mode.

 Picture and Clip Settings: Set the saving paths of the captured pictures and

clipped video files. Valid for the pictures you capture with the web browser.

 Save snapshots in live view to: Set the saving path of the manually captured

pictures in live view mode.

 Save snapshots when playback to: Set the saving path of the captured

pictures in playback mode.

 Save clips to: Set the saving path of the clipped video files in playback mode.

Note: You can click Browse to change the directory for saving the clips and pictures,

and click Open to open the set folder of clips and picture saving.

3. Click to save the settings. Save

Thermal Network Bullet Camera User Manual

5.2 Configure System Settings

Purpose:

Follow the instructions below to configure the system settings, include System

Settings, Maintenance, Security, and User Management, etc.

5.2.1 Configuring Basic Information

Enter the Device Information interface: Configuration > System > System

Settings Basic Information > .

In the interface, you can edit the Device Name and Device No.. Basic Information

Other information of the network camera, such as Model, Serial No., Firmware

Version, Encoding Version, Number of Channels, Number of HDDs, Number of

Alarm Input and Number of Alarm Output are displayed. The information cannot be

changed in this menu. It is the reference for maintenance or modification in future.

Figure 5-2 Basic Information

Specyfikacje produktu

Marka:	Hikvision
Kategoria:	Kamera monitorująca
Model:	DS-2TD2166-7/V1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hikvision DS-2TD2166-7/V1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kamera monitorująca Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025

Hikvision DS-2CE16H0T-IT1E Instrukcja

11 Stycznia 2025

Hikvision THC-T127-PTLTS Instrukcja

7 Stycznia 2025

Hikvision DS-2CE16U0T-LF Instrukcja

19 Grudnia 2024

Hikvision DS-2CE10KF3T-LSYE Instrukcja

19 Grudnia 2024

Hikvision DS-2CE10KF3T-LS Instrukcja

19 Grudnia 2024

Hikvision DS-2CE76U0T-LMF Instrukcja

19 Grudnia 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Technaxx TX-192 Instrukcja

28 Stycznia 2025

Wisenet XNV-8080R Instrukcja

25 Stycznia 2025

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025

Speco Technologies O2P30X Instrukcja

12 Stycznia 2025

Kguard QRT-501 Instrukcja

11 Stycznia 2025