Instrukcja obsługi Hikvision DS-2CD2T55FWD-I8

Hikvision Kamera monitorująca DS-2CD2T55FWD-I8

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hikvision DS-2CD2T55FWD-I8 (174 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/174

Network Camera User Manual

User Manual

UD06747B

Network Camera

Network Camera User Manual

User Manual

Any and all information, including, among others, wordings, pictures, graphs are the

properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries

(hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be

“the Manual”) cannot be reproduced, changed, translated, or distributed, partially or

wholly, by any means, without the prior written permission of Hikvision. Unless

otherwise stipulated, Hikvision does not make any warranties, guarantees or

representations, express or implied, regarding to the Manual.

About this Manual

This Manual is applicable to Network Camera.

The Manual includes instructions for using and managing the product. Pictures, charts,

images and all other information hereinafter are for description and explanation only.

The information contained in the Manual is subject to change, without notice, due to

ﬁrmware updates or other reasons. Please ﬁnd the latest version in the company

website (http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision's trademarks and logos are the properties of

Hikvision in various jurisdictions. Other trademarks and logos mentioned below are

the properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE

PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND

HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,

Network Camera User Manual

FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF

THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,

EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,

CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING,

AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS

INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN

CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF

PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL

NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,

PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER

ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET

SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY

TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL

RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT

IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE

LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS

PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE

APPLICABLE LAW, THE LATER PREVAILS.

Safety Instruction

These instructions are intended to ensure that the user can use the product correctly to

avoid danger or property loss.

Notice:

If camera fails to synchronize local time with that of the network, you need to set

up camera time manually. Visit the camera and enter system setting interface for

time setting.

Network Camera User Manual

The precaution measure is divided into ‘Warnings’ and ‘Cautions’:

Warnings: Serious injury or death may be caused if any of these warnings are

neglected.

Cautions: Injury or equipment damage may be caused if any of these cautions are

neglected.

Warnings Follow these safeguards to

prevent serious injury or death.

Cautions Follow these precautions to

prevent potential injury or material

damage.

Warnings:

 Please adopt the power adapter which can meet the safety extra low voltage

(SELV) standard. And source with 12 V or 24 VDC AC (depending on models)

according to the IEC60950-1 and Limited Power Source standard.

 To reduce the risk of ﬁre or electrical shock, do not expose this product to rain or

moisture.

 This installation should be made by a qualiﬁed service person and should conform

to all the local codes.

 Please install blackouts equipment into the power supply circuit for convenient

supply interruption.

 Please make sure that the ceiling can support more than 50(N) Newton gravities if

the camera is fixed to the ceiling.

 If the product does not work properly, please contact your dealer or the nearest

service center. Never attempt to disassemble the camera yourself. (We shall not

assume any responsibility for problems caused by unauthorized repair or

maintenance.)

Cautions:

Network Camera User Manual

 Make sure the power supply voltage is correct before using the camera.

 Do not drop the camera or subject it to physical shock.

 Do not touch sensor modules with fingers. If cleaning is necessary, use a clean

cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an

extended period of time, put on the lens cap to protect the sensor from dirt.

 Do not aim the camera lens at the strong light such as sun or incandescent lamp.

The strong light can cause fatal damage to the camera.

 The sensor may be burned out by a laser beam, so when any laser equipment is

being used, make sure that the surface of the sensor not be exposed to the laser

beam.

 Do not place the camera in extremely hot, cold temperatures (refer to product

speciﬁcation for working temperature), dusty or damp environment, and do not

expose it to high electromagnetic radiation.

 To avoid heat accumulation, ensure there is good ventilation to the device.

 Keep the camera away from water and any liquids.

 While shipping, pack the camera in its original, or equivalent, packing materials.

Or packing the same texture.

 Improper use or replacement of the battery may result in hazard of explosion.

Please use the manufacturer recommended battery type.

Notes:

For the camera supports IR, you are required to pay attention to the following

precautions to prevent IR reﬂection:

 Dust or grease on the dome cover will cause IR reﬂection. Please do not remove

the dome cover ﬁlm until the installation is ﬁnished. If there is dust or grease on

the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol.

 Make certain the installation location does not have reﬂective surfaces of objects

too close to the camera. The IR light from the camera may reﬂect back into the

lens causing reﬂection.

 The foam ring around the lens must be seated ﬂush against the inner surface of

the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera

Network Camera User Manual

body so that the foam ring and the dome cover are attached seamlessly.

Network Camera User Manual

Table of Contents

Chapter 1 System Requirement .............................................................................. 1

Chapter 2 Network Connection .............................................................................. 2

2.1 Seng the Network Camera over the LAN .......................................................... 2

2.1.1 Wiring over the LAN ..................................................................................................... 2

2.1.2 Acvating the Camera .................................................................................................. 3

2.1.3 (Oponal) Seing Security Queson 9............................................................................

2.2 Seng the Network Camera over the WAN ......................................................... 9

2.2.1 Stac IP Connecon ................................................................................................... 10

2.2.2 Dynamic IP Connection .............................................................................................. 11

Chapter 3 Access to the Network Camera ............................................................ 13

3.1 Accessing by Web Browsers ............................................................................... 13

3.2 Accessing by Client Soware .............................................................................14

Chapter 4 -Fi Settings Wi ...................................................................................... 16

4.1 Conguring Wi- Connecon in Manage and Ad-hoc Modes Fi ............................ 16

4.2 Easy Wi-Fi Connecon with WPS funcon ......................................................... 21

4.3 IP Property Setngs for Wireless Network Connecon ...................................... 23

Chapter 5 Live View ............................................................................................. 25

5.1 Live View Page ................................................................................................... 25

5.2 Starng Live View .............................................................................................. 26

5.3 Recording and Capturing Pictures Manually ...................................................... 27

5.4 Operang PTZ Control ........................................................................................ 27

5.4.1 PTZ Control Panel ....................................................................................................... 27

5.4.2 Setng/Calling a Preset .............................................................................................. 28

5.4.3 Setng/Calling a Patrol ............................................................................................... 29

Chapter 6 Network Camera Conﬁguration .......................................................... 31

6.1 Conguring Local Parameters .............................................................................31

6.2 Congure System Sengs .................................................................................. 33

6.2.1 Conguring Basic Informaon .................................................................................... 33

6.2.2 Conguring Time Seings ..........................................................................................34

6.2.3 Conguring RS232 Setngs......................................................................................... 36

6.2.4 Conguring RS485 Setngs......................................................................................... 36

6.2.5 Conguring DST Setngs ............................................................................................ 37

6.2.6 Conguring External Devices ...................................................................................... 38

6.2.7 Conguring VCA Resource .......................................................................................... 39

6.2.8 Open Source Soware License ................................................................................... 40

Network Camera User Manual

6.3 Maintenance ...................................................................................................... 40

6.3.1 Upgrade & Maintenance ............................................................................................ 40

6.3.2 Log ............................................................................................................................41

6.3.3 System Service ........................................................................................................... 43

6.4 Security Setngs ................................................................................................ 43

6.4.1 Authencaon ........................................................................................................... 43

6.4.2 IP Address Filter ......................................................................................................... 44

6.4.3 Security Service .........................................................................................................45

6.5 User Management ............................................................................................. 46

6.5.1 User Management ..................................................................................................... 46

6.5.2 Security Queson ......................................................................................................48

6.5.3 Online Users ..............................................................................................................49

Chapter 7 Network Settings ................................................................................. 50

7.1 Conguring Basic Setngs .................................................................................. 50

7.1.1 Conguring TCP/IP Setngs ........................................................................................ 50

7.1.2 Conguring DDNS Setngs ......................................................................................... 52

7.1.3 Conguring PPPoE Sengs ........................................................................................54

7.1.4 Conguring Port Setngs ............................................................................................ 54

7.1.5 Congure NAT (Network Address Translation) Sengs ............................................... 55

7.2 Congure Advanced Setngs ............................................................................. 56

7.2.1 Conguring SNMP Sengs ......................................................................................... 56

7.2.2 Conguring FTP Setngs .............................................................................................59

7.2.3 Conguring Email Setngs .......................................................................................... 61

7.2.4 Plaorm Access ......................................................................................................... 63

7.2.5 Wireless Dial .............................................................................................................. 64

7.2.6 HTTPS Sengs ........................................................................................................... 66

7.2.7 Conguring QoS Setngs ............................................................................................ 68

7.2.8 Conguring 802.1X Setngs .......................................................................................68

7.2.9 Integraon Protocol ................................................................................................... 70

7.2.10 Bandwidth Adaptation ............................................................................................... 70

Chapter 8 Video/Audio Settings ........................................................................... 72

8.1 Conguring Video Setngs ................................................................................. 72

8.2 Conguring Audio Setngs ................................................................................. 75

8.3 Conguring ROI Encoding ...................................................................................76

8.4 Display Info. on Stream ...................................................................................... 78

8.5 Conguring Target Cropping ............................................................................... 79

Chapter 9 Image Settings ..................................................................................... 80

9.1 Conguring Display Sengs ............................................................................... 80

9.1.1 Day/Night Auto-Switch ............................................................................................... 80

Network Camera User Manual

9.1.2 Day/Night Scheduled-Switch ...................................................................................... 84

9.2 Conguring OSD Sengs ................................................................................... 85

9.3 Conguring Privacy Mask ................................................................................... 87

9.4 Conguring Picture Overlay ............................................................................... 88

Chapter 10 Event Settings .................................................................................. 90

10.1 Basic Events ....................................................................................................... 90

10.1.1 Conguring Moon Detecon .................................................................................... 90

10.1.2 Conguring Video Tampering Alarm ........................................................................... 96

10.1.3 Conguring Alarm Input ............................................................................................. 97

10.1.4 Conguring Alarm Output .......................................................................................... 99

10.1.5 Handling Excepon .................................................................................................. 100

10.1.6 Conguring Other Alarm .......................................................................................... 100

10.2 Smart Events .................................................................................................... 103

10.2.1 Conguring Audio Excepon Detection .................................................................... 104

10.2.2 Conguring Defocus Detection ................................................................................. 105

10.2.3 Conguring Scene Change Detecon ........................................................................ 106

10.2.4 Conguring Face Detecon ...................................................................................... 107

10.2.5 Conguring Intrusion Detecon ............................................................................... 109

10.2.6 Conguring Line Crossing Detecon ......................................................................... 111

10.2.7 Conguring Region Entrance Detecon .................................................................... 114

10.2.8 Conguring Region Exiting Detecon ........................................................................ 115

10.2.9 Conguring Unattended Baggage Detecon ............................................................. 117

10.2.10 Conguring Object Removal Detection ................................................................119

10.3 VCA Conguraon ............................................................................................ 121

10.3.1 Behavior Analysis ..................................................................................................... 121

10.3.2 Face Capture ............................................................................................................ 128

10.3.3 People Counting ...................................................................................................... 132

10.3.4 Counng .................................................................................................................. 135

10.3.5 Heat Map................................................................................................................. 136

10.3.6 Road Trac .............................................................................................................. 138

Chapter 11 Storage Settings ............................................................................. 141

11.1 Conguring Record Schedule ........................................................................... 141

11.2 Congure Capture Schedule ............................................................................. 144

11.3 Conguring Net HDD ........................................................................................ 146

11.4 Memory Card Detection ................................................................................... 148

11.5 Conguring Lite Storage ................................................................................... 150

Chapter 12 Playback ........................................................................................ 152

Chapter 13 Picture ........................................................................................... 154

Network Camera User Manual

Chapter 14 Application .................................................................................... 155

14.1 Face Capture Stascs ..................................................................................... 155

14.2 People Counng Stascs ................................................................................ 155

14.3 Heat Map Stascs .......................................................................................... 156

14.4 Counng Stascs ........................................................................................... 157

Appendix............................................................................................................... 159

Appendix 1 SADP Software Introduction ..................................................................159

Appendix 2 Port Mapping ..........................................................................................162

0505001070731

Network Camera User Manual

Chapter 1 System Requirement

Operating System: Microsoft Windows XP SP1 and above version

CPU: 2.0 GHz or higher

RAM: 1G or higher

Display: 1024×768 resolution or higher

Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above

version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above

version.

Network Camera User Manual

Chapter 2 Network Connection

Note:

 You shall acknowledge that the use of the product with Internet access might be

under network security risks. For avoidance of any network attacks and

information leakage, please strengthen your own protection. If the product does

not work properly, please contact with your dealer or the nearest service center.

 To ensure the network security of the network camera, we recommend you to

have the network camera assessed and maintained termly. You can contact us if

you need such service.

Before you start:

 If you want to set the network camera via LAN (Local Area Network), please a

refer to Section 2.1 Setting the Network Camera over the LAN.

 If you want to set the network camera via WAN (Wide Area Network), please a

refer to Section 2.2 Setting the Network Camera over the WAN.

Setting the Network Camera over the LAN 2.1

Purpose:

To view and conﬁgure the camera via LAN, you need to connect the network a

camera in the same subnet with your computer, and install the SADP or iVMS-4200

software to search and change the IP of the network camera.

Note: For the detailed introduction of SADP, please refer to Appendix 1.

Wiring over the LAN 2.1.1

The following ﬁgures show the two ways of cable connection of network camera a

and computer: a

Purpose:

 To test the network camera, you can directly connect the network camera to the

computer with a network cable as shown in Figure 2-1.

Network Camera User Manual

 Refer to the Figure 2-2 to set network camera over the LAN via a switch or a

router.

Network Cable

Network Camera

Computer

Connecting Directly Figure 2-1

Network Cable

Network Camera Computer

Connecting via a Switch or Router Figure 2-2 a

Activating the Camera 2.1.2

You are required to activate the camera ﬁrst by setting a strong password for it before

you can use the camera.

Activation via Web Browser, Activation via SADP, and Activation via Client Software

are all supported.

 Activation via Web Browser

Steps:

1. Power on the camera, and connect the camera to the network.

2. Input the IP address into the address bar of the web browser, and click Enter to

enter the activation interface.

Notes:

 The default IP address of the camera is 192.168.1.64.

 The computer and the camera should belong to the same subnet.

 For the camera enables the DHCP by default, you need to use the SADP software

Network Camera User Manual

to search the IP address.

Activation via Web Browser Figure 2-3

3. Create a password and input the password into the password ﬁeld.

STRONG PASSWORD RECOMMENDED–We highly recommend you

create a strong password of your own choosing (using a minimum of 8

characters, including at least three of the following categories: upper case letters,

lower case letters, numbers, and special characters) in order to increase the

security of your product. And we recommend you reset your password regularly,

especially in the high security system, resetting the password monthly or weekly

can better protect your product.

4. Conﬁrm the password.

5. Click to save the password and enter the live view interface. OK

 Activation via SADP Software

SADP software is used for detecting the online device, activating the camera, and

resetting the password.

Get the SADP software from the supplied disk or the ofﬁcial website, and install the

SADP according to the prompts. Follow the steps to activate the camera.

Steps:

1. Run the SADP software to search the online devices.

2. Check the device status from the device list, and select the inactive device.

Network Camera User Manual

SADP Interface Figure 2-4

Note:

The SADP software supports activating the camera in batch. Refer to the user manual

of SADP software for details.

3. Create a password and input the password in the password field, and conﬁrm the

password.

STRONG PASSWORD RECOMMENDED– We highly recommend

you create a strong password of your own choosing (using a minimum

of 8 characters, including at least three of the following categories:

upper case letters, lower case letters, numbers, and special characters) in

order to increase the security of your product. And we recommend you

reset your password regularly, especially in the high security system,

resetting the password monthly or weekly can better protect your

product.

Note:

You can enable the Hik-Connect service for the device during activation.

4. Click start activation. Activate to

You can check whether the activation is completed on the popup window. If activation

failed, please make sure that the password meets the requirement and try again.

5. Change the device IP address to the same subnet with your computer by either

modifying the IP address manually or checking the checkbox of Enable DHCP.

Select inacve device.

Input and conrm

password.

Network Camera User Manual

Modify the IP Address Figure 2-5

6. Input the admin password and click to activate your IP address Modify

modiﬁcation.

The batch IP address modiﬁcation is supported by the SADP. Refer to the user manual

of SADP for details.

 Activation via Client Software

The client software is versatile video management software for multiple kinds of

devices.

Get the client software from the supplied disk or the official website, and install the

software according to the prompts. Follow the steps to activate the camera.

Step s:

1. Run the client software and the control panel of the software pops up, as shown in

the ﬁgure below.

Network Camera User Manual

Control Panel Figure 2-6

2. Click the Device Management icon to enter the Device Management interface, as

shown in the figure below.

Network Camera User Manual

Device Management Interface Figure 2-7

3. Check the device status from the device list, and select an inactive device.

4. Click the button to pop up the Activation interface. Activate

5. Create a password and input the password in the password field, and conﬁrm the

password.

STRONG PASSWORD RECOMMENDED–We highly recommend

you create a strong password of your own choosing (using a minimum of

8 characters, including at least three of the following categories: upper

case letters, lower case letters, numbers, and special characters) in order

to increase the security of your product. We recommend you reset your

password regularly, especially in the high security system, resetting the

password monthly or weekly can better protect your product.

Activation Interface (Client Software) Figure 2-8

6. Click button to start activation. OK

7. Click the Modify Netinfo button to pop up the Network Parameter Modification

interface, as shown in the ﬁgure below.

Network Camera User Manual

Modifying the Network Parameters Figure 2-9

8. Change the device IP address to the same subnet with your computer by either

modifying the IP address manually or checking the checkbox of Enable DHCP.

9. Input the password to activate your IP address modiﬁcation.

(Optional) Setting Security Question 2.1.3

Security question is used to reset the admin password when admin user forgets the

password.

Admin user can follow the pop-up window to complete security question settings

during camera activation. Or, admin user can go to User Management interface to set

up the function.

Setting the Network Camera over the WAN 2.2

Purpose:

This section explains how to connect the network camera to the WAN with a static IP

or a dynamic IP.

Network Camera User Manual

Static IP Connection 2.2.1

Before you start:

Please apply a static IP from an ISP (Internet Service Provider). With the static IP

address, you can connect the network camera via a router or connect it to the WAN

directly.

 Connecting the network camera via a router

Steps:

1. Connect the network camera to the router.

2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2

for detailed IP address conﬁguration of the network camera.

3. Save the static IP in the router.

4. Set port mapping, e.g 80, 8000, and 554 ports. The steps for port mapping vary .,

according to the different routers. Please call the router manufacturer for

assistance with port mapping.

Note: Refer to Appendix 2 for detailed information about port mapping.

5. Visit the network camera through a web browser or the client software over the

internet.

Accessing the Camera through Router with Static IP Figure 2-10

 Connecting the network camera with static IP directly

You can also save the static IP in the camera and directly connect it to the internet

without using a router. Refer to Section 2.1.2 for detailed IP address configuration of

the network camera.

Network Camera User Manual

Accessing the Camera with Static IP Directly Figure 2-11

Dynamic IP Connection 2.2.2

Before you start:

Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect

the network camera a modem or a router. to

 Connecting the network camera via a router

Steps:

1. Connect the network camera to the router.

2. In the camera, assign a LAN IP address, the subnet mask and the gateway. Refer

to Section 2.1.2 for detailed IP address configuration of the network camera.

3. In the router, set the PPPoE user name, password and confirm the password.

4. Set port mapping. E.g. 80, 8000, and 554 ports. The steps for port mapping vary

depending on different routers. Please call the router manufacturer for assistance

with port mapping.

Note: Refer to Appendix 2 for detailed information about port mapping.

5. Apply a domain name from a domain name provider.

6. Configure the DDNS settings in the setting interface of the router.

7. Visit the camera via the applied domain name.

 Connecting the network camera via a modem

Purpose:

This camera supports the PPPoE auto dial-up function. The camera gets a public IP

address by ADSL dial-up after the camera is connected to a modem. You need to

configure the PPPoE parameters of the network camera. Refer to Section 7.1.3

Configuring PPPoE Settings for detailed configuration.

Accessing the Camera with Dynamic IP Figure 2-12

Network Camera User Manual

Note: The obtained IP address is dynamically assigned via PPPoE, so the IP address

always changes after rebooting the camera. To solve the inconvenience of the

dynamic IP, you need to get a domain name from the DDNS provider (E.g.

DynDns.com). Please follow the steps below for normal domain name resolution and

private domain name resolution to solve the problem.

 Normal Domain Name Resolution

Normal Domain Name Resolution Figure 2-13

Steps:

1. Apply a domain name from a domain name provider.

2. Conﬁgure the DDNS settings in the DDNS Settings interface of the network

camera. Refer to Section 7.1.2 Configuring DDNS Settings for detailed

conﬁguration.

3. Visit the camera via the applied domain name.

Network Camera User Manual

Chapter 3 the Network Access to

Camera

Accessing by Web Browsers 3.1

Steps:

1. Open the web browser.

2. In the browser address bar, input the IP address of the network camera, and press

the Enter key to enter the login interface.

Note:

The default IP address is 192.168.1.64. You are recommended to change the IP

address to the same subnet with your computer.

3. Input the user name and password and click . Login

The admin user should configure the device accounts and user/operator permissions

properly. Delete the unnecessary accounts and user/operator permissions.

Note:

The IP address gets locked if the admin user performs 7 failed password attempts

(5 attempts for the user/operator).

4. Click . Login

5. Install the plug-in before viewing the live video and operating the camera. Follow

the installation prompts to install the plug- . in

Network Camera User Manual

Download and Install Plug- Figure 3-2 in

Note: You may have to close the web browser to finish the installation of the

plug-in.

6. Reopen the web browser after the installation of the plug-in and repeat steps 2 to 4

to login.

Note: For detailed instructions of further configuration, please refer to the user

manual of network camera.

Accessing by Client Software 3.2

The product CD contains the iVMS-4200 client software. You can view the live video

and manage the camera with the software .

Follow the installation prompts to install the software. The control panel and live view

interface of iVMS-4200 client software are shown as below.

Network Camera User Manual

iVMS-4200 Control Panel Figure 3-3

iVMS-4200 Main View Figure 3-4

Network Camera User Manual

Chapter 4 -Fi Settings Wi

Purpose:

By connecting to the wireless network, you don’t need to use cable of any kind for

network connection, which is very convenient for the actual surveillance application.

Note: This chapter is only applicable for the cameras with the built-in Wi-Fi module.

Configuring Wi-Fi Connection in Manage and 4.1

Ad-hoc Modes

Purpose:

Two connection modes are supported. Choose a mode as desired and perform the

steps to configure the Wi-Fi.

Wireless Connection in Manage Mode

Steps:

1. Enter the Wi-Fi configuration interface.

Configuration> Network> Advanced Settings> - Wi Fi

2. Click Search to search the online wireless connections.

Wi-Fi List Figure 4-1

Network Camera User Manual

3. Click to choose a wireless connection on the list.

Wi-Fi Setting- Manage Mode Figure 4-2

4. Check the radio button to select the Network mode Manage,as and the

Security mode of the network is automatically shown when you select the

wireless network, please don’t change it manually.

Note: These parameters are exactly identical with those of the router.

5. Enter the key to connect the wireless network. The key should be that of the

wireless network connection you set on the router.

Wireless Connection in Ad-hoc Mode

If you choose the Ad-hoc mode, you don’t need to connect the wireless camera via a

router. The scenario is the same as you connect the camera and the PC directly with a

network cable.

Steps:

1. Choose Ad-hoc mode.

Wi-Fi Setting- Ad-hoc Figure 4-3

Network Camera User Manual

2. Customize a SSID for the camera.

3. Choose the Security Mode of the wireless connection.

4. Enable the wireless connection function for your PC.

5. On the PC side, search the network and you can see the SSID of the camera

listed.

Ad-hoc Connection Point Figure 4-4

6. Choose the SSID and connect.

Security Mode Description:

Security Mode Figure 4-5

You can choose the Security Mode as not-encrypted, WEP, WPA-personal,

WPA-enterprise, WPA2-personal, and WPA2-enterprise.

WEP mode:

Network Camera User Manual

WEP Mode Figure 4-6

 Authentication - Select Open or Shared Key System Authentication, depending on

the method used by your access point. Not all access points have this option, in

which case they probably use Open System, which is sometimes known as SSID

Authentication.

 Key length - This sets the length of the key used for the wireless encryption, 64 or

128 bit. The encryption key length can sometimes be shown as 40/64 and

104/128.

 Key type The key types available depend on the access point being used. The -

following options are available:

HEX - Allows you to manually enter the hex key.

ASCII - In this method the string must be exactly 5 characters for 64-bit WEP and

13 characters for 128-bit WEP.

WPA-personal and WPA2-personal Mode:

Enter the required Pre-shared Key for the access point, which can be a hexadecimal

number or a passphrase.

Security Mode- WPA-personal Figure 4-7

WPA- enterprise and WPA2-enterprise Mode:

Network Camera User Manual

Choose the type of client/server authentication being used by the access point;

EAP-TLS or EAP-PEAP.

EAP-TLS

EAP-TLS Figure 4-8

 Identity - Enter the user ID to present to the network.

 Private key password Enter the password for your user ID. –

 EAPOL version - Select the version used (1 or 2) in your access point.

 CA Certificates - Upload a CA certificate to present to the access point for

authentication.

EAP-PEAP:

 User Name - Enter the user name to present to the network

 Password - Enter the password of the network

 PEAP Version - Select the PEAP version used at the access point.

 Label - Select the label used by the access point.

 EAPOL version - Select version (1 or 2) depending on the version used at the

access point

 CA Certificates - Upload a CA certificate to present to the access point for

authentication

 For your privacy and to better protect your system against security risks, we

Network Camera User Manual

strongly recommend the use of strong passwords for all functions and network

devices. The password should be something of your own choosing (using a

minimum of 8 characters, including at least three of the following categories:

upper case letters, lower case letters, numbers and special characters) in order to

increase the security of your product.

 Proper configuration of all passwords and other security settings is the

responsibility of the installer and/or end-user.

Easy Wi-Fi Connection with WPS function 4.2

Purpose:

The setting of the wireless network connection is never easy. To avoid the complex

setting of the wireless connection you can enable the WPS function.

WPS (Wi-Fi Protected Setup) refers to the easy configuration of the encrypted

connection between the device and the wireless router. The WPS makes it easy to add

new devices to an existing network without entering long passphrases. There are two

modes of the WPS connection, the PBC mode and the PIN mode.

Note: If you enable the WPS function, you do not need to configure the parameters

such as the encryption type and you don’t need to know the key of the wireless

connection.

Steps:

Wi-Fi Settings - WPS Figure 4-9

Network Camera User Manual

PBC Mode:

PBC refers to the Push-Button-Configuration, in which the user simply has to push a

button, either an actual or virtual one (as the button on the configuration

interface of the IE browser), on both the Access Point (and a registrar of the network)

and the new wireless client device.

1. Check the checkbox of to enable WPS.

2. Choose the connection mode as PBC.

Note: Support of this mode is mandatory for both the Access Points and the

connecting devices.

3. Check on the Wi-Fi router to see if there is a WPS button. If yes push the button

and you can see the indicator near the button start flashing, which means the WPS

function of the router is enabled. For detailed operation, please see the user guide of

the router.

4. Push the WPS button to enable the function on the camera.

If there is not a WPS button on the camera, you can also click the virtual button to

enable the PBC function on the web interface.

5. Click button. Connect

When the PBC mode is both enabled in the router and the camera, the camera and the

wireless network is connected automatically.

PIN Mode:

The PIN mode requires a Personal Identification Number (PIN) to be read from either

a sticker or the display on the new wireless device. This PIN must then be entered to

connect the network, usually the Access Point of the network.

Steps:

1. Choose a wireless connection on the list and the SSID is loaded automatically .

2. Choose Use route PIN code.

Network Camera User Manual

Use PIN Code Figure 4-10

If the PIN code is generated from the router side, you should enter the PIN code you

get from the router side in the Router PIN code field.

3. Click . Connect

You can generate the PIN code on the camera side. And the expired time for the PIN

code is 120 seconds.

1. Click Generate.

2. Enter the code to the router, in the example, enter 48167581 to the router.

IP Property Settings for Wireless Network 4.3

Connection

The default IP address of wireless network interface controller is 192.168.1.64. When

you connect the wireless network you can change the default IP.

Steps:

1. Enter the TCP/IP configuration interface.

Configuration> Network> Basic Settings > TCP/IP

2. Select the Wlan tab.

Network Camera User Manual

Setting WLAN Parameters Figure 4-11

3. Customize the IPv4 address, the IPv4 Subnet Mask and the Default Gateway.

The setting procedure is the same with that of LAN.

If you want to be assigned the IP address you can check the checkbox to enable

the DHCP.

Network Camera User Manual

Chapter 5 Live View

Live View Page 5.1

Purpose:

The live view page allows you to view the real-time video, capture images, realize

PTZ control, set/call presets and configure video parameters.

Log the network camera to enter the live view page, or you can click in Live View on

the menu bar of the main page to enter the live view page.

Descriptions of the live view page:

Toolbar

Live View

Window

Menu Bar

PTZ Control

Panel

Preset/Patrol

Settings

Live View Page Figure 5-1

Menu Bar:

Click each tab to enter Live View, Playback, Picture, Application, d Configuration an

page respectively.

Live View Window:

Display the live video.

Toolbar:

Toolbar allows you to adjust the live view window size the stream type, and the ,

plug- s. It also allows you to process the operations on the live view page, e.gin .,

start/stop live view, capture, record, audio on/off, two- y audio, start/stop digital wa

zoom, etc.

Network Camera User Manual

For IE (Internet Explorer) users plug-ins webcomponents and quick time are , as

selectable. And for Non-IE users, webcomponents, quick time, VLC or MJPEG is

selectable if they are supported by the web browser.

PTZ Control:

Perform panning, tilting and zooming actions of the camera. Control the light and the

wiper (only available for cameras supporting PTZ function).

Preset/Patrol Settings :

Set/call/delete the presets or patrols for PTZ cameras.

Starting Live View 5.2

In the live view window as shown in Figure 4-2, click on the toolbar to start the

live view of the camera.

Live View Toolbar Figure 5-2

Table 5-1 Descriptions of the Toolbar

Icon

Description

Start/Stop live view.

The window size is 4:3.

The window size is 16:9.

The original widow size.

Self-adaptive window size.

Live view with the main stream.

Live view with the sub stream.

Live view with the third stream.

Click to select the third-party plug-in.

Manually capture the picture.

Manually start/stop recording.

Audio on and adjust volume /Mute.

Turn on/oﬀ microphone.

Start/stop digital zoom function.

Note: The icons vary according to the diﬀerent camera models.

Network Camera User Manual

Click the zoom/focus/iris buttons to realize lens control.

Notes:

 There are eight direction arrows ( , , , , , , in the control , )

panel. Click the arrows to realize adjustment in the relative positions.

 For the cameras which support lens movements only, the direction buttons are

invalid.

Table 5-2 Descripti ons of PTZ Control Panel

Icon

Description

Zoom in/out

Focus near/far

Iris / + -

PTZ speed adjustment

Light on/off

Wiper on/oﬀ

Auxiliary focus

Initialize lens

Adjust speed of pan/tilt movements

Start Manual Tracking

Start 3D Zoom

Setting/Calling a Preset 5.4.2

 Setting a Preset:

1. In the PTZ control panel, select a preset number from the preset list.

Network Camera User Manual

Setting a Preset Figure 5-4

2. Use the PTZ control buttons to move the lens the desired position. to

• Pan the camera to the right or left.

• Tilt the camera up or down.

• Zoom in or out.

• Refocus the lens.

3. Click to ﬁnish the setting of the current preset.

4. You can click to delete the preset.

 Calling a Preset:

This feature enables the camera to point to a specified preset scene manually or when

an event takes place.

For the deﬁned preset, you can call it at any time to the desired preset scene.

In the PTZ control panel, select a deﬁned preset from the list and click to call the

preset.

Or you can place the mouse on the presets interface, and call the preset by typing the

preset No. to call the corresponding presets.

Calling a Preset Figure 5-5

Setting/Calling a Patrol 5.4.3

Note:

No less than 2 presets have to be configured before you set a patrol.

Steps:

1. Click to enter the patrol configuration interface.

Network Camera User Manual

2. Select a path No., and click to add the conﬁgured presets.

3. Select the preset, and input the patrol duration and patrol speed.

4. Click OK to save the ﬁrst preset.

5. Follow the steps above to add the other presets.

Figure 5-6 Add Patrol Path

6. Click to save a patrol. OK

7. Click to start the patrol, and click to stop it.

8. (Optional) Click to delete a patrol.

Network Camera User Manual

Chapter 6 Network Camera

Conﬁguration

Conﬁguring Local Parameters 6.1

Purpose:

The local conﬁguration refers to the parameters of the live view, record ﬁles and

captured pictures. The record ﬁles and captured pictures are the ones you record and

capture using the web browser and thus the saving paths of them are on the PC

running the browser.

Steps:

1. Enter the Local Configuration interface: >Conﬁguration Local.

Local Configuration Interface Figure 6-1

2. Conﬁgure the following settings:

 Live View Parameters: Set the protocol type and live view performance.

 Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.

TCP: Ensures complete delivery of streaming data and better video quality,

yet the real-time transmission will be affected.

UDP: Provides real-time audio and video streams.

Network Camera User Manual

HTTP: Allows the same quality as of TCP without setting speciﬁc ports for

streaming under some network environments.

MULTICAST: It’s recommended to select MCAST type when using the

Multicast function. For detailed information about Multicast, refer to Section

7.1.1 Conﬁguring TCP/IP Settings.

 Play Performance: Set the play performance to Shortest Delay or Auto.

 Rules: It refers to the rules on your local browser, select enable or disable to

display or not display the colored marks when the motion detection, face

detection, or intrusion detection is triggered. E.g., enabled as the rules are, and

the face detection is enabled as well, when a face is detected, it will be marked

with a green rectangle on the live view.

 Image Format: Choose the image format for picture capture.

 Record File Settings: Set the saving path of the recorded video files. Valid for the

record ﬁles you recorded with the web browser.

 Record File Size: Select the packed size of the manually recorded and

downloaded video ﬁles to 256M, 512M or 1G. After the selection, the

maximum record ﬁle size is the value you selected.

 Save record ﬁles to: Set the saving path for the manually recorded video files.

 Save downloaded ﬁles to: Set the saving path for the downloaded video ﬁles

in playback mode.

 Picture and Clip Settings: Set the saving paths of the captured pictures and

clipped video ﬁles. Valid for the pictures you capture with the web browser.

 Save snapshots in live view to: Set the saving path of the manually captured

pictures in live view mode.

 Save snapshots when playback to: Set the saving path of the captured

pictures in playback mode.

 Save clips to: Set the saving path of the clipped video ﬁles in playback mode.

Note: You can click Browse to change the directory for saving the clips and pictures,

and click Open to open the set folder of clips and picture saving.

3. Click to save the settings. Save

Network Camera User Manual

Conﬁgure System Settings 6.2

Purpose:

Follow the instructions below to configure the system settings, include System

Settings, Maintenance, Security, and User Management etc. ,

Conﬁguring Basic Information 6.2.1

Enter the Device Information interface: Conﬁguration > System > System Settings >

Basic Information.

In the interface, you can edit the Device Name and Device No.. Basic Information

Other information of the network camera, such as Model, Serial No., Firmware

Version, Encoding Version, Number of Channels, Number of HDDs, Number of

Alarm Input and Number of Alarm Output are displayed. The information cannot be

changed in this menu. It is the reference for maintenance or modiﬁcation in future.

Online Upgrade

For some camera models, when memory card is mounted, you can click the Update

button that appears on the right of Firmware Version text ﬁeld to see if there is a new

version available. If a new version is available, the version number will be displayed

in the New Version text ﬁeld below, and you can click the Upgrade button to upgrade

the firmware for the camera.

Online Upgrade Figure 6-2

Note: When the camera is upgrading, don't power oﬀ the camera. During upgrading,

the camera may not be accessible. You need to wait 1 or 2 minutes before the upgrade

ﬁnishes.

Network Camera User Manual

Conﬁguring Time Settings 6.2.2

Purpose :

You can follow the instructions in this section to conﬁgure the time synchronization

and DST settings.

Steps:

1. Enter the Time Settings interface, Conﬁguration > System> System Settings >

Time Settings .

Time Settings Figure 6-3

2. Select the Time Zone of your location from the drop-down menu.

3. Conﬁgure the NTP settings.

(1) Click to enable the function. NTP

(2) Conﬁgure the following settings:

Server Address: IP address of NTP server.

NTP Port: Port of NTP server.

Interval: The time interval between the two synchronizing actions with NTP

server.

(3) (Optional) You can click the Test button to test the time synchronization

Network Camera User Manual

function via NTP server.

Time Sync by NTP Server Figure 6-4

Note: If the camera is connected to a public network, you should use a NTP server

that has a time synchronization function, such as the server at the National Time

Center (IP Address: 210.72.145.44). If the camera is set in a customized network,

NTP software can be used to establish a NTP server for time synchronization.

 Conﬁgure the manual time synchronization.

(1) Check the Manual Time Sync. item to enable the manual time

synchronization function.

(2) Click the icon select the date, time from the pop-up calendar. to

(3) (Optional) You can check Sync. with computer time item to synchronize the

time of the device with that of the local PC.

Time Sync Manually Figure 6-5

 Click to save the settings. Save

Network Camera User Manual

the PTZ parameters should be done before you control the PTZ unit.

Steps:

1. Enter RS-485 Port Setting interface: Conﬁguration System System Settings> > >

RS485.

RS-485 Settings Figure 6-7

2. Set the RS485 parameters and click to save the settings. Save

By default, the Baud Rate is set as 9600 bps, the Data Bit is 8, the stop bit is 1 and

the Parity and Flow Control is None.

Note: The Baud Rate, PTZ Protocol and PTZ Address parameters should be exactly

the same as the PTZ camera parameters.

Conﬁguring DST Settings 6.2.5

Purpose:

Daylight Saving Time (DST) is a way of making better use of the natural daylight by

setting your clock forward one hour during the summer months, and back again in the

fall.

Conﬁgure the DST according to your actual demand.

Steps:

Network Camera User Manual

1. Enter the DST conﬁguration interface.

Conﬁguration System System Settings DST> > >

DST Settings Figure 6-8

2. Select the start time and the end time.

3. Select the DST Bias.

4. Click to activate the settings. Save

Conﬁguring External Devices 6.2.6

Purpose:

For the device supported external devices, including the wiper on the housing or the

LED light, you can control them via the Web browser. External devices vary

according to the diﬀerent camera models.

Steps:

1. Enter the External Device configuration interface.

Conﬁguration System> > System Settings External Device >

External Device Settings Figure 6-9

2. Check the Enable Supplement Light checkbox to enable the LED Light.

3. Move the slider to adjust the low beam brightness and high bean brightness.

Network Camera User Manual

4. Select the mode for LED light. Timing and Auto are selectable.

 Timing: The LED will be turned on by the schedule you set. You should set

the Start Time and End Time.

Set Schedule Figure 6-10

 Auto: The LED will be turned on according to the environment illumination.

5. Click Save to save the settings.

Conﬁguring VCA Resource 6.2.7

Purpose:

VCA resource offers you options to enable certain VCA functions according to actual

need when several VCA functions are available. It helps allocate more resources to

the wanted functions.

VCA Resource Conﬁguration Figure 6-11

Steps:

1. Enter VCA Resource conﬁguration interface:

Conﬁguration > System > System Settings > VCA Resource

2. Select a desired VCA combination. SMART Event + Face Detection and SMART

Event + Heat Map are selectable.

3. Click to save the settings. A reboot is required after setting the VCA Save

Resource.

Network Camera User Manual

Notes:

• VCA Resource function varies according to different camera models.

• Face Detection and Heat Map are mutually exclusive. When SMART Event +

Heat Map is enabled, Face Detection interface will not be displayed.

• The function may not be supported by some camera models.

Open Source Software License 6.2.8

Information about the open source software that applies to the IP camera can be

checked if required. Go to Conﬁguration > System Settings > About.

Maintenance 6.3

Upgrade & Maintenance 6.3.1

Purpose:

The upgrade & maintenance interface allows you to process the operations, including

reboot, partly restore, restore to default, export/import the conﬁguration ﬁles, and

upgrade the device.

Enter the Maintenance interface: Conﬁguration stem Maintenance > Sy > >

Upgrade & Maintenance.

 Reboot: Restart the device.

 Restore: Reset all the parameters, except the IP parameters and user information,

to the default settings.

 Default: Restore all the parameters to the factory default.

Notes:

• After restoring the default settings, the IP address is also restored to the

default IP address, please be careful for this action.

• For camera that supports Wi-Fi, wireless dial, or wlan function, Restore

action does not restore the related settings of mentioned functions to default.

 Information Export

Network Camera User Manual

Device Parameters: click to export the current conﬁguration file of the camera.

This operation requires admin password to proceed.

For the exported ﬁle, you also have to create an encryption password. The

encryption password is required when you import the ﬁle to other cameras.

Diagnose Information: click to download log and system information.

 Import Conﬁg. File

Conﬁguration ﬁle is used for the batch conﬁguration of the camera s.

Steps:

1. Click Browse to select the saved conﬁguration ﬁle.

2. Click and input encryption password to start importing conﬁguration Import

ﬁle.

Note: You need to reboot the camera after importing configuration ﬁle.

 Upgrade: Upgrade the device to a certain version.

Steps:

1. Select ﬁrmware or ﬁrmware directory to locate the upgrade ﬁle.

Firmware: Locate the exact path of the upgrade ﬁle.

Firmware Directory: Only the directory the upgrade ﬁle belongs to is

required.

2. Click Browse to select the local upgrade ﬁle and then click to start Upgrade

remote upgrade.

Note: The upgrading process will take 1 to 10 minutes. Please don't disconnect

power of the camera during the process, and the camera reboots automatically

after upgrade.

Log 6.3.2

Purpose:

The operation, alarm, exception and information of the camera can be stored in log

ﬁles. You can also export the log ﬁles on your demand.

Before you start:

Network Camera User Manual

Please configure network storage for the camera or insert a SD card in the camera.

Steps:

1. Enter log searching interface : Conﬁguration System Maintenance Log > > > .

Log Searching Interface Figure 6-12

2. Set the log search conditions to specify the search, including the Major Type,

Minor Type, Start Time and End Time.

3. Click Search to search log ﬁles. The matched log ﬁles will be displayed on the

log list interface.

Log Searching Figure 6-13

4. To export the log ﬁles, click to save the log ﬁles. Export

Network Camera User Manual

Authentication Figure 6-15

2. Set up authentication method for RTSP authentication and WEB authentication.

Caution:

Digest is the recommended authentication method for better data security. You

must be aware of the risk if you adopt basic as the authentication method.

3. Click to save the settings. Save

IP Address Filter 6.4.2

Purpose:

This function makes it possible for access control.

Steps:

1. Enter the IP Address Filter interface: Conﬁguration > System > Security IP >

Address Filter

IP Address Filter Interface Figure 6-16

2. Check the checkbox of Enable IP Address Filter.

3. Select the type of IP Address Filter in the drop-down list, Forbidden and Allowed

are selectable.

4. Set the IP Address Filter list.

 Add an IP Address

Network Camera User Manual

1. Enter the security service conﬁguration interface : Conﬁguration > System >

Security Security Service > .

Security Service Figure 6-19

2. Check the checkbox of . Enable Illegal Login Lock

Illegal Login Lock: it is used to limit the user login attempts. Login attempt from

the IP address is rejected if admin user performs 7 failed user name/password

attempts (5 times for the operator/user).

Note: If the IP address rejected, you can try to login the device after 30 minutes. is

User Management 6.5

User Management 6.5.1



 As Administrator

The admin user can add, delete or modify user accounts, and grant them different

permissions. We highly recommend you manage the user accounts and

permissions properly.

Enter the User Management interface: > > Conﬁguration System User

Management

Note:

Admin password if required for adding and modifying a user account.

Network Camera User Manual

password regularly, especially in the high security system, resetting the

password monthly or weekly can better protect your product.

3. You can check or uncheck the permissions.

4. Click to finish the user modification. OK

 Deleting a User

Steps:

1. Click to select the user you want to delete and click . Delete

2. Click on the pop-up dialogue box to confirm the deletion. OK



 As Operator or User

Operator or user can modify password. Old password is required for this action.

Security Question 6.5.2

Purpose:

Security question is used to reset the admin password when admin user forgets the

password.

Set Security Question:

You can set the security questions during camera activation. Or you can set the

function at user management interface.

Security question setting is not cleared when you restore the camera (not to default).

Steps:

1. Enter setting interface:

Configuration > System > User Management > User Management

2. Click Security Question.

3. Input correct admin password.

4. Select questions and input answers.

5. Click to save the settings. OK

Reset Admin Password:

Before you start:

The PC used to reset password and the camera should belong to the same IP address

Network Camera User Manual

Figure 7-2 DynDNS Settings



 NO-IP:

Steps:

(1) Choose the DDNS Type as NO-IP.

Figure 7-3 -IP DNS Settings NO

(2) Enter the Server Address as www.noip.com

(3) Enter the Domain name you registered.

(4) Enter the User Name and Password.

(5) Click and then you can view the camera with the domain name. Save

Note: Reboot the device to make the settings take effect.

Network Camera User Manual

Configuring PPPoE Settings 7.1.3

Steps:

1. Enter the PPPoE Settings interface: Configuration > Network > Basic Settings >

PPPoE

PPPoE Settings Figure 7-4

2. Check the Enable PPPoE checkbox to enable this feature.

3. Enter User Name Password Confirm , , and password for PPPoE access.

Note: The User Name and Password should be assigned by your ISP.

 For your privacy and to better protect your system against security risks, we

strongly recommend the use of strong passwords for all functions and network

devices. The password should be something of your own choosing (using a

minimum of 8 characters, including at least three of the following categories:

upper case letters, lower case letters, numbers and special characters) in order to

increase the security of your product.

 Proper configuration of all passwords and other security settings is the

responsibility of the installer and/or end-user.

4. Click to save and exit the interface. Save

Note: A reboot is required for the settings to take effect.

Configuring Port Settings 7.1.4

Purpose:

Network Camera User Manual

The UPnP protocol allows devices to connect seamlessly and to simplify the

implementation of networks in the home and corporate environments.

With the function enabled, you don’t need to configure the port mapping for each port,

and the camera is connected to the Wide Area Network via the router.

Steps:

1. Enter the NAT settings interface. Configuration > Network > Basic Settings >

NAT.

2. Check the checkbox to enable the UPnP™ function.

3. Choose a nickname for the camera, or you can use the default name.

4. Select the port mapping mode. Manual and Auto are selectable. And for manual

port mapping, you can customize the value of the external port.

5. Click to save the settings. Save

UPnP Settings Figure 7-6

Configure Advanced Settings 7.2

Purpose:

You can configure the parameters, including SNMP, FTP, Email, HTTPS, QoS,

802.1x, etc., by following the instructions in this section.

Configuring SNMP Settings 7.2.1

Purpose:

Specyfikacje produktu

Marka:	Hikvision
Kategoria:	Kamera monitorująca
Model:	DS-2CD2T55FWD-I8
Kolor produktu:	Czerwony
Typ produktu:	Zestaw do budowania
Wysokość opakowania:	- mm
Głębokość opakowania:	- mm
Certyfikat środowiskowy (zrównoważonego rozwoju):	Forest Stewardship Council (FSC) Mix
Waga wraz z opakowaniem:	- g
Zalecany wiek (min):	9 lat(a)
Zalecany wiek (max):	16 lat(a)
Sugerowana płeć:	Chłopak, dziewczyna
Liczba części:	499 szt.
Ostrzeżenie UE TSD:	Zabawka nieodpowiednia dla dzieci poniżej 36. miesiąca życia
Wymiary montażowe:	440 x 460 x 170 mm