Instrukcja obsługi HiKOKI DS14DBL2
HiKOKI
maszyna wiertnicza
DS14DBL2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla HiKOKI DS14DBL2 (60 stron) w kategorii maszyna wiertnicza. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/60
Handling instructions
使用說明書
취급 설명서
Hướng dẫn sử dụng
คูมือการใชงาน
Petunjuk pemakaian
en
zh
ko
vi
th
id
ar
DS18DBL2 DV18DBL2
DS14DBL2 • DS18DBL2
DV14DBL2 • DV18DBL2
en
zh
ko
vi
th
id
ar
2
English
power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your fi nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may aff ect the
power tool s operation.ʼ
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations diff erent from
those intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another
battery pack.
b) Use power tools only with specifi cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off position before connecting to
3
English
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
CORDLESS DRIVER DRILL / IMPACT
DRIVER DRILL SAFETY WARNINGS
<DV14DBL2 / DV18DBL2>
1. Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
<DS14DBL2 / DS18DBL2 / DV14DBL2 / DV18DBL2>
1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fastener may contact hidden wiring.
Cutting accessory and fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. Make sure that the area to be drilled is absolutely free
of any hidden obstructions including electrical wiring,
water, or gas pipes. Drilling into the aforementioned may
result in electric shock or short circuit, gas leak or other
hazards that can cause serious accidents or injuries.
2. When using the tool, make sure the side handle is
attached and fi rmly secured.
If not fi rmly secured, the tool may jerk out of position
when overburdened, resulting in injury.
Tighten the side handle so that the protrusion of the
handle points towards the upper surface of the unit.
( )Fig. 3-b
Prior to use, always make sure that the side handle is not
loose.
If the handle loosens during use, tighten it further.
3. During operation, make sure to fi rmly hold the tool’s
handle and side handle with both hands. Failure to do so
may result in injury.
4. Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
5. Setting up and checking the work environment. Check
if the work environment is suitable by following the
precaution.
6. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
7. Never disassemble the rechargeable battery and
charger.
8. Never short-circuit the rechargeable battery.
Shortcircuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
9. Do not dispose of the battery in fi re. If the battery is burnt,
it may explode.
10. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
11. Do not insert object into the air ventilation slots of the
charger. Inserting metal objects or infl ammables into the
charger air ventilation slots will result in electrical shock
hazard or damaged charger.
12. When mounting a bit into the keyless chuck, tighten the
sleeve adequately. If the sleeve is not tight, the bit may
slip or fall out, causing injury.
13. When changing the rotational speed with the shift knob,
confi rm that the switch is off . Changing the speed while
the motor is rotating will damage the gears.
14. The clutch dial cannot be set between the numerals "1,
4, 7 … 22" or the dots, and do not use with the clutch dial
numeral between "22" and the line at the middle of the
drill mark. Doing so may cause damage.
15. Always use this unit with clockwise rotation, when using
it as impact drill.
16. Resting the unit after continuous work.
17. The power tool is equipped with a temperature
protection circuit to protect the motor. Continuous work
may cause the temperature of the unit to rise, activating
the temperature protection circuit and automatically
stopping operation. If this happens, allow the power tool
to cool before resuming use.
18. The motor may stop in the event the tool is overloaded. In
this should occur, release the tool’s switch and eliminate
the cause of the overload.
Avoid touching the front case which can heat up during
continuous operation.
19. The motor rotation may be locked to cease while the unit
is used as drill. While operating the driver drill, take care
not to lock the motor.
20. The use of the battery in a cold condition (below 0 degree
Centigrade) can sometimes result in the weakened
tightening torque and reduced amount of work. This,
however, is a temporary phenomenon, and returns to
normal when the battery warms up.
21. Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
When electing to carry the tool hooked to your hip belt,
make sure to detach the tool bit and side handle. Failure
to do so may result in unexpected injury.
22. Do not look directly into the light. Such actions could
result in eye injury.
Wipe off any dirt or grime attached to the lens of the LED
light with a soft cloth, being careful not to scratch the
lens.
Scratches on the lens of the LED light can result in
decreased brightness.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may stop.
This is not the trouble but the result of protection function.
1. When the battery power remaining runs out, the motor
stops.
In such a case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
Specyfikacje produktu
| Marka: | HiKOKI |
| Kategoria: | maszyna wiertnicza |
| Model: | DS14DBL2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z HiKOKI DS14DBL2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna wiertnicza HiKOKI
24 Października 2024
24 Października 2024
24 Października 2024
21 Czerwca 2024
21 Czerwca 2024
21 Czerwca 2024
21 Czerwca 2024
21 Czerwca 2024
21 Czerwca 2024
21 Czerwca 2024
Instrukcje maszyna wiertnicza
- maszyna wiertnicza Worx
- maszyna wiertnicza Milwaukee
- maszyna wiertnicza Bosch
- maszyna wiertnicza Parkside
- maszyna wiertnicza Global
- maszyna wiertnicza Festool
- maszyna wiertnicza Bavaria By Einhell
- maszyna wiertnicza Stanley
- maszyna wiertnicza Black & Decker
- maszyna wiertnicza Scheppach
- maszyna wiertnicza Proxxon
- maszyna wiertnicza DeWalt
- maszyna wiertnicza Einhell
- maszyna wiertnicza Genesis
- maszyna wiertnicza Silverline
- maszyna wiertnicza Makita
- maszyna wiertnicza Ozito
- maszyna wiertnicza RYOBI
- maszyna wiertnicza DEDRA
- maszyna wiertnicza Baumr-AG
- maszyna wiertnicza Hilti
- maszyna wiertnicza Rodcraft
- maszyna wiertnicza Trotec
- maszyna wiertnicza Dremel
- maszyna wiertnicza Velleman
- maszyna wiertnicza Meec Tools
- maszyna wiertnicza Güde
- maszyna wiertnicza Zipper
- maszyna wiertnicza McKenzie
- maszyna wiertnicza Ferm
- maszyna wiertnicza Hitachi
- maszyna wiertnicza Craftsman
- maszyna wiertnicza Ridgid
- maszyna wiertnicza PowerPlus
- maszyna wiertnicza Alpha Tools
- maszyna wiertnicza Proviel
- maszyna wiertnicza Porter-Cable
- maszyna wiertnicza Metabo
- maszyna wiertnicza C-Power
- maszyna wiertnicza Cotech
- maszyna wiertnicza Skil
- maszyna wiertnicza Maestro
- maszyna wiertnicza Clas Ohlson
- maszyna wiertnicza Laserliner
- maszyna wiertnicza Cocraft
- maszyna wiertnicza Pansam
- maszyna wiertnicza Wolfcraft
- maszyna wiertnicza Kinzo
- maszyna wiertnicza Luxor
- maszyna wiertnicza Kress
Najnowsze instrukcje dla maszyna wiertnicza
22 Października 2024
22 Października 2024
22 Października 2024
7 Października 2024
6 Października 2024
1 Października 2024
1 Października 2024
1 Października 2024
28 Września 2024
28 Września 2024