Instrukcja obsługi HiKOKI CM75EAP

HiKOKI Podcinacz CM75EAP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla HiKOKI CM75EAP (53 stron) w kategorii Podcinacz. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/53
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand
this manual BEFORE operating the power tool. Please keep this manual available for other
users and owners before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort
ou de sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce
mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil
motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización de esta herramienta eléctrica puede provocar INAPROPIADA O PELIGROSA
lesiones graves o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda
este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan
leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado
en un lugar seguro.
Model
Mole
Modelo
CM 75EAP / CM 75EBP
Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
English
2
Pay special attention to statements preceded by the
following words:
WARNING
Indicates a strong possibility of severe personal
injury or loss of life if instructions are not followed.
CAUTION
Indicates a possibility of personal injury or
equipment damage if instructions are not
followed.
NOTE
Helpful information for correct function and use.
MEANINGS OF SYMBOLS
NOTE: Some units do not carry them.
Symbols
WARNING
The following show symbols used for the
machine. Be sure that you understand
their meaning before use.
Cutter, Portable cut-o machine
CM75EAP / CM75EBP
It is important that you read, fully
understand and observe the following
safety precautions and warnings.
Careless or improper use of the unit
may cause serious or fatal injury.
Read, understand and follow all
warnings and instructions in this manual
and on the unit.
Always wear eye, head and ear
protectors, and also dust protection,
when using this unit
Choke
On / Start
O / Stop
Emergency stop
Maximum spindle speed of the machine.
Warning: Do not use wheels that are
rated for speeds lower than the indicated
maximum spindle speed of the machine.
Fire warning! This tool generates sparks
when cutting metal.
Warning! Do not use damaged cut-o
wheel.
Rotation direction of cut-o wheel
Cut-o wheel dimensions
Fuel and oil mixture
Carburetor adjustment - Idle speed
Carburetor adjustment - Low speed
mixture
Carburetor adjustment - High speed
mixture
Priming pump
Decompression valve
Hazardous dust and gas emission
warning
Kickback warning
Warning! Never use blades designed for
cutting wood.
English
3
WHAT IS WHAT? (Fig. 1)
A: Stop switch: Device for allowing the engine to be
started or stopped.
B: Throttle lever: Device activated by the operatorʼs
nger, for controlling the engine speed.
C: Throttle lever lockout: Device that prevents the
accidental operation of the throttle lever until
manually released.
D: Throttle lock: Device for setting the throttle in
partially open position to aid starting.
E: Fuel tank cap: For closing the fuel tank.
F: Starter knob: Pull handle to start the engine.
G: Front handle: Support handle located at or
towards the front of the engine housing.
H: Rear handle: Support handle located at or
towards the rear of the engine housing.
I: Choke lever: Device for enriching the fuel/air
mixture in the carburetor, to aid starting.
J: Priming pump: Device for supplying extra fuel, to
aid starting.
K: Cleaner box (B): Cover for pre- lter
L: Cleaner box (A): Cover for paper- lter and
carburetor.
M: Clutch cover: Device between the engine and
the cutting equipment designed to prevent
unintentional contact with the transmission.
N: Arm cover: Device between the engine and
the cutting equipment designed to prevent
unintentional contact with the transmission.
O: Wheel guard: Cover which is intended to protect
the operator from wheel contact, and also directs
debris away from the operator.
P: Nut: Secures the wheel guard to engine.
Q: Anti-vibration spring: Reduce the transmission of
vibrations to the operator’s hands.
R: Handle(W): Handle for rotating the wheel guard.
S: Decompression valve: Device for reducing the
compression pressure of engine to aid starting.
T: Tensioner bolt: Device to increase and release
belt tension.
U: Tension nut: Mark for indicating the state of
tension of the belt.
V: Cut-o wheel: Bonded abrasive with reinforced
resinoid wheel for cutting, with blotter.
W: Coupler: Device for attaching the hose
X: Valve: Device for adjusting water ow rate.
Y: Mu er: Reduces engine exhaust noise and
directs the exhaust gases.
Z: Wheel washer: Flange provided to clamp and
drive the cut-o wheel.
a: Bolt: Secures the cut-o wheel
b: Adapter collar: Spindle attachment for using
arbor hole 1" (25.4 mm) cut-o wheels.
c: Combi box spanner: Maintenance tool for
removing or installing a spark plug
d: Hex. wrench: Maintenance tool for removing
cover and tensioning the belt.
e: Protective glasses: Eye protection.
f: Handling instructions: Included with unit. Read
before operation and keep for future reference to
learn proper, safe techniques.
Fig. 1
R
a
OGL
K
F
H
Q
Y
Q
Z
V
J
S
Q
EW
XM
UT
N
P
AI
C
DB
ef
bcd


Specyfikacje produktu

Marka: HiKOKI
Kategoria: Podcinacz
Model: CM75EAP

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z HiKOKI CM75EAP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Podcinacz HiKOKI

HiKOKI

HiKOKI TCG27EBS Instrukcja

24 Września 2024
HiKOKI

HiKOKI CH10DL Instrukcja

24 Września 2024
HiKOKI

HiKOKI CG24EC Instrukcja

24 Września 2024
HiKOKI

HiKOKI TCG23EC Instrukcja

24 Września 2024
HiKOKI

HiKOKI TCG24EBS Instrukcja

24 Września 2024
HiKOKI

HiKOKI CG24EBS Instrukcja

24 Września 2024
HiKOKI

HiKOKI TCG24EC Instrukcja

24 Września 2024
HiKOKI

HiKOKI M6SB Instrukcja

24 Września 2024
HiKOKI

HiKOKI M3608DA Instrukcja

24 Września 2024
HiKOKI

HiKOKI 18DSDL Instrukcja

24 Września 2024

Instrukcje Podcinacz

Najnowsze instrukcje dla Podcinacz

Black & Decker

Black & Decker GL570 Instrukcja

15 Października 2024
Husqvarna

Husqvarna 236R Instrukcja

14 Października 2024
RYOBI

RYOBI One+ P20220 Instrukcja

9 Października 2024
Husqvarna

Husqvarna 110iL Instrukcja

9 Października 2024
Toro

Toro 51434 Instrukcja

8 Października 2024
Toro

Toro 51490 Instrukcja

8 Października 2024
Toro

Toro 51494 Instrukcja

8 Października 2024
Toro

Toro 51498T Instrukcja

8 Października 2024
Toro

Toro 51653 Instrukcja

8 Października 2024
Toro

Toro i51020 Instrukcja

8 Października 2024