Instrukcja obsługi Hifonics ZEUS ZG-1200.4

Hifonics odbiornik ZEUS ZG-1200.4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hifonics ZEUS ZG-1200.4 (2 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
ZG-1200.2
ZG-600.4
ZG-1200.4
ZG-1200.1D
ZG-1800.1D
ZG-2400.1D
ZG-3200.1D
40A x 1
40A x 1
50A x 1
60A x 1
80A x 1
00A x 11
External 150A
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model. Some models require
an external fuse.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
a secure surface. Do not mount
Attach the chassis ground
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
output of the source unit.
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
Connect the speaker cables to
the speaker output connectors.
Follow the diagram below
The chassis ground connection
is critical to the performance
location that is close to the
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Speaker
Connections
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Stereo
Installation
Before you start
Monoblock single woofer multiple woofersMonoblock
Bridged
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
104
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
PEAKER
LEFT RIGHT
BRIDGED
OUTPUT
S EAKER OUTPUT PEAKER OUTPUT
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
9
6V 0.2V
INPUT
LEVEL
Model Fuse Size Cable Size
4ga
Setup Common System Setup
Quick Start
The input MODE switch will “sum” or
combine the right and left channel signals
in the MONO position to improve bass
performance. Select MONO only when the
amp is being used for subwoofers.
The XOVER Mode switch sets the type
of crossover that will be active. 4 channel
models will have two switches, one for each
set of channels.
output below the selected frequency. This
is typically used to protect midrange and hi
frequency speakers from damage and to
allow a smooth transition from a subwoofer.
will limit output above the selected
frequency. This is used to allow
a smooth transition to the higher
frequency speakers.
1.
turned down (counter clockwise).
2.
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or “0” adjustment. Make sure that the green LED on
3. Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5.
the level down (counter clockwise) until the distortion is eliminated. Small
The Bass EQ control will increase the power
output at 45Hz for more pronounced bass.
Exercise caution when using this control.
Increase the level in small amounts until
distortion is noticed, then back off a little.
Some models include a bass
remote. Avoid adjusting the bass
remote while operating vehicle.
Input Mode
Xover Mode
High pass
Adjustment
Low pass
Adjustment
Bass Boost
Remote Level
Control
2ch - Full Range
4ch - Full Range
4ch - Mixed Mono
Mono
5ch
A
B
C
D
E
F
is properly adjusted to match the signal
output level of your source unit.
THIS IS NOT A VOLUME CONTROL!
Level Setting
G
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
consequential damages connected therewith. To view the full warranty, please visit the website.
The information contained within this document is intended to offer some basic guidelines
for a few of the most common installations. More complex audio systems should be
installed by a competent professional. Additional installation information available at
www.maxxsonics.com
Hifonics products are designed and engineered in the USA by
www.maxxsonics.com
MONO STEREO
MODE
FULL LPF HPF
XOVER
60 1.2KHz
HPF
30 250Hz
LPF
40 300Hz
LPF
6V 0.2V
INPUT
LEVEL
SPEAKER
LEFT RIGHT
BRIDGED
OUTPUT
SPEAKER OUTPUT
CH 1 CH 2
BRIDGED
PEAKER OUTPUT
CH 1 CH 2
BRIDGED
PEAKER OUTPUT
CH 3 CH 4
BRIDGED
PEAKER OUTPUT
SPEAKER
CH 3 CH 4
BRIDGED
OUTPUT
This “Quick Start Installation” guide is meant to help you
“hook up” and play music. For more detailed information,
http://hifonics.com/manuals.html
HF ZG 2020 SP QSG 01 - rev1
FULL LPF HPF
XOVER
MONOSTEREO
MODE
40 300Hz
LPF
10 40Hz
SUBSONIC
X-OVER
LPFFULL HPF
6V 0.2V
LEVELBASS EQ
0 12dB30 250Hz
LPF
60 1.2KHz
HPF
CHANNEL 1/2
6V 0.2V
LEVEL BASS EQ
0 12dB 30 250Hz
LPF
60 1.2KHz
HPF
CHANNEL 3/4
FULLLPF HPF
X-OVER
HPFFULL
X-OVER
2CH 4CH3CH
MODE
6V 0.2V
LEVELBASS EQ
0 12dB30 250Hz
LPF
60 1.2KHz
HPF
CHANNEL 1/2
6V 0.2V
LEVEL BASS EQ
0 12dB 30 250Hz
LPF
60 1.2KHz
HPF
CHANNEL 3/4
FULLLPF HPF
X-OVER X-OVER
LPFFULL HPF
2CH 4CH3CH
MODE
2CH/4CH
0 12dB
1CH
0 9dB


Specyfikacje produktu

Marka: Hifonics
Kategoria: odbiornik
Model: ZEUS ZG-1200.4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hifonics ZEUS ZG-1200.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje odbiornik Hifonics

Hifonics

Hifonics HAC-5000.1D Instrukcja

5 Października 2024
Hifonics

Hifonics HAC-3000.1D Instrukcja

5 Października 2024
Hifonics

Hifonics HAC-3000.4D Instrukcja

5 Października 2024
Hifonics

Hifonics HCM-800.4D Instrukcja

5 Października 2024
Hifonics

Hifonics HAC-2000.4D Instrukcja

5 Października 2024
Hifonics

Hifonics HAC-1500.1D Instrukcja

5 Października 2024
Hifonics

Hifonics HCM-1500.1D Instrukcja

4 Października 2024
Hifonics

Hifonics Pluto II Instrukcja

2 Października 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024