Instrukcja obsługi Harman Kardon HKTS 200

Harman Kardon głośnik HKTS 200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Harman Kardon HKTS 200 (6 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
Subwoofer
HKTS 210 SUB/HKTS 200 SUB
Owner’s Manual
2
HKTS 210 SUB/HKTS 200 SUB Introduction, Included Items and
Subwoofer Rear-Panel Controls
Introduction
Thank you for choosing this Harman Kardon product!
Your new Harman Kardon 200-watt powered subwoofer incorporates an 8" (200mm)
down-firing cone transducer and a built-in, high-performance, 200-watt amplifier that
delivers the powerful, dynamic and accurate low-frequency performance that makes
your film soundtracks and music come alive. And with line-level and LFE inputs, phase
control and automatic turn-on/turn-off, the HKTS 210 SUB/HKTS 200 SUB is also simple
to connect and set up.
We’re confident that this Harman Kardon subwoofer will provide every note of enjoyment
that you expect – and that when you think about purchasing additional audio equipment,
you will once again choose Harman Kardon products.
This owner’s manual contains all the information you need to set up, connect
and adjust your new subwoofer. For more in-depth information, go to our Web site:
www.harmankardon.com.
NOTE: This owner’s manual covers both the HKTS 210 SUB and HKTS 200 SUB models.
All contents cover both models except where noted.
Included Items
One powered subwoofer
One combination LFE and trigger cable
Subwoofer Rear-Panel Controls
Phase Switch
Phase Switch
Bass Boost Switch
Bass Boost Switch
Power On
Mode Switch
Power On
Mode Switch
Input Mode Switch
External Trigger
Input Connector
External Trigger
Input Connector
Line-Level LFE In Connector
Line-Level LFE In Connector
Line-Level L/R In Connector
Line-Level L/R In Connector
Power Switch
Power Switch
Power Cord
Power Cord
Subwoofer
Level Control
Subwoofer
Level Control
Top: HKTS 210 SUB Rear-Panel; Bottom: HKTS 200 SUB Rear-Panel
3
HKTS 210 SUB/HKTS 200 SUB Subwoofer Rear-Panel Controls
and Placing the Subwoofer
Phase switch: This switch determines whether the subwoofer transducer’s piston-like
action moves in and out in phase with the satellite speakers. If the subwoofer were to
play out of phase with the satellite speakers, the sound waves from the satellites could
cancel out some of the subwoofer’s sound waves, reducing bass performance and sonic
impact. This phenomenon depends in part on the placement of all the speakers in the
room. In most cases, the Phase switch should be left in the “Normal” position. However,
it does no harm to experiment, and you can leave the Phase switch in the position that
maximizes bass response and impact.
Bass Boost switch: Set this switch to “On” to enhance the subwoofer’s low-frequency
performance. Set this switch to “Off” for normal low-frequency performance.
Power On Mode switch: When this switch is set in the “Auto” position and when the
Power switch is set to “On,” the subwoofer will automatically turn itself on when it
receives an audio signal and will enter the standby mode after it has received no audio
signal for about 15 minutes. When this switch is set in the “On” position, the subwoofer
will remain on whether or not it is receiving an audio signal. An LED on the subwoofer’s
top panel indicates whether the subwoofer is in the on or standby state:
• When the LED glows white, the subwoofer is turned on.
• When the LED is not illuminated, the subwoofer is in the standby mode. When the
Power switch is set to “Off,” the LED will not be illuminated, no matter what setting
the Power On Mode switch is in.
Subwoofer Level control: Use this control to adjust the subwoofer’s volume. Turn
clockwise to increase the volume; turn counterclockwise to decrease the volume.
Input Mode switch (HKTS 210 SUB only): When this switch is in the “Normal” setting,
the input signal from the Line-Level L/R In connectors is active. When this switch is in
the “LFE” setting, the input signal from the Line-Level LFE In connector is active.
External Trigger Input connector: Use the mini plug of the supplied combination LFE
and trigger cable to connect the External Trigger Input connector to the trigger output
of another compatible component. Whenever the subwoofer detects a trigger signal
between 3V and 30V (AC or DC), its amplifier will turn on. The amplifier will turn off after
the trigger signal ceases, even when the Power On Mode switch is in the “Auto” position.
Line-Level LFE In connector: The signal from this connector bypasses the subwoofer’s
internal low-pass crossover. When you’re connecting the subwoofer to the dedicated
subwoofer output of a receiver/processor that has its own low-pass crossover network,
use the Line-Level LFE In connector. You must also set the HKTS 210 SUB only:
subwoofer’s Input Mode switch in the “LFE” position.
Line-Level L/R In connectors: The signals from these connectors pass through the
subwoofer’s internal low-pass crossover. When you’re connecting the subwoofer to the
preamp or subwoofer outputs of a receiver/processor that does not have its own low-
pass crossover network, use both Line-Level L/R In connectors. HKTS 210 SUB only:
You must also set the Input Mode switch in the “Normal” position. If your receiver/
processor has only one subwoofer output, you can use either the L or R connector.
Power switch: Set this switch in the “On” position to turn the subwoofer on. The
subwoofer will then be either on or in the standby mode, depending on the setting of the
Power On Mode switch.
Power Cord (non-detachable): After you have made and verified all the connections
described in this manual, plug this cord into an active, electrical outlet for unswitched
proper operation of the subwoofer. DO NOT plug this cord into the accessory outlets
found in some audio components.
Placing the Subwoofer
The performance of a subwoofer is directly related to its placement in the listening room
and its physical position relative to the other speakers in the system.
While it is true that in general our ears do not hear directional sounds at the low
frequencies where subwoofers operate, when installing a subwoofer within the limited
confines of a room, the reflections, standing waves and absorptions generated within
the room will strongly influence the performance of any subwoofer system. As a result,
the specific location of the subwoofer in the room does become important to the amount
and quality of bass that is produced.
For example, placing the subwoofer next to a wall generally will increase the amount of
bass in the room; placing it in a corner (1) generally will maximize amount of bass in the
room. However, corner placement can also increase the destructive effect of standing
waves on bass performance. This effect can vary depending on the listening position –
some listening positions may yield very good results while others may have far too much
(or too little) bass at certain frequencies.
In many rooms, placing the subwoofer along the same plane as the left and right
speakers (2) can produce the best integration between the sound of the subwoofer and
that of the left and right speakers. In some rooms, the best performance could even
result from placing the subwoofer behind the listening position (3).
We strongly recommend that you experiment with placement before choosing a final
location for your subwoofer. One way you can determine the best location for the
subwoofer is by temporarily placing it in the listening position and playing music with
strong bass content. Move around to various locations in the room while the system
is playing (putting your ears where the subwoofer would be placed), and listen until
you find the location where the bass performance is best. Place the subwoofer in that
location.
3.
2.
TV
Front Left
Speaker
Surround Left
Speaker
Surround Right
Speaker
Front Right
Speaker
Center
Speaker
1.

Specyfikacje produktu

Marka: Harman Kardon
Kategoria: głośnik
Model: HKTS 200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Harman Kardon HKTS 200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Harman Kardon

Harman Kardon

Harman Kardon Onyx Studio 8 Instrukcja

30 Grudnia 2025
Harman Kardon

Harman Kardon Luna Instrukcja

30 Grudnia 2025
Harman Kardon

Harman Kardon HKB4 Instrukcja

26 Grudnia 2024
Harman Kardon

Harman Kardon Champagne Instrukcja

26 Grudnia 2024
Harman Kardon

Harman Kardon HKTW6 Instrukcja

26 Grudnia 2024
Harman Kardon

Harman Kardon Citation ONE DUO MKIII Instrukcja

26 Grudnia 2024
Harman Kardon

Harman Kardon HK195 Instrukcja

26 Grudnia 2024
Harman Kardon

Harman Kardon HK-595 Instrukcja

26 Grudnia 2024
Harman Kardon

Harman Kardon HKB6 Instrukcja

26 Grudnia 2024
Harman Kardon

Harman Kardon HKTS 18 Instrukcja

25 Grudnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025
Hifonics

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025
Pyle

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025
ION

ION Insta Sound Instrukcja

15 Stycznia 2025
Pure Acoustics

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025
Yamaha

Yamaha WX-010 Instrukcja

15 Stycznia 2025
Polk

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025
Sennheiser

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025