Instrukcja obsługi Hanwha HCP-6320

Hanwha Kamera monitorująca HCP-6320

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hanwha HCP-6320 (93 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/93
HCP-6320/HCP-6320H
AHD SPEED DOME CAMERA
User Manual
Copyright
© 2016 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered
trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or
wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee
shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Hanwha Techwin reserves the right to change the contents of this document without prior notice.
Design and specications are subject to change without prior notice.
AHD SPEED DOME CAMERA
User Manual
English - 3
●safety information
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
WARNING
•To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
•To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
- Do NOT use power sources other than Class 2 power source.
- REPLACE WITH SAME TYPE 250V T3.15AL FUSE(F1)
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water
on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fire or electric shock.
9.
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product
in any way. (Hanwha Techwin is not liable for problems caused by unauthorized modifications or attempted repair.
10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric
shock.
CAUTION - Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 55°C), low temperature (below -50°C), or high
humidity. Doing so may cause fire or electric shock.
3.
If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire
or damage to the product.

Specyfikacje produktu

Marka: Hanwha
Kategoria: Kamera monitorująca
Model: HCP-6320

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hanwha HCP-6320, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Hanwha

Hanwha

Hanwha PNM-C34404RQPZ Instrukcja

3 Października 2024
Hanwha

Hanwha XNO-9083R Instrukcja

2 Października 2024
Hanwha

Hanwha LNO-6012R Instrukcja

2 Października 2024
Hanwha

Hanwha XNV-6081R Instrukcja

2 Października 2024
Hanwha

Hanwha QNO-7022R Instrukcja

1 Października 2024
Hanwha

Hanwha XNO-9082R Instrukcja

1 Października 2024
Hanwha

Hanwha XNV-8081RE Instrukcja

1 Października 2024
Hanwha

Hanwha HCD-6070R Instrukcja

1 Października 2024
Hanwha

Hanwha QND-8020R Instrukcja

1 Października 2024
Hanwha

Hanwha QND-7080R Instrukcja

1 Października 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Trebs

Trebs CCD-401C Instrukcja

15 Października 2024
Hikvision

Hikvision DS-2CE56D5T-AIRZ Instrukcja

15 Października 2024
D-Link

D-Link DCS-7510 Instrukcja

15 Października 2024
Ubiquiti Networks

Ubiquiti Networks UniFi Video UVC-G3-AF Instrukcja

14 Października 2024
Hikvision

Hikvision DS-2TD2137-7/VP Instrukcja

13 Października 2024
Alecto

Alecto DVC-215IP Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2325FWD-I Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2323G2-IU Instrukcja

12 Października 2024