Instrukcja obsługi Haier HW-18LWA03/R2(T3)

Haier nieskategoryzowany HW-18LWA03/R2(T3)

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Haier HW-18LWA03/R2(T3) (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

ROOM AIR CONDITIONER

Your model will be the same as one of the above two operation panels.

Note :

Your model may differ from the one shown.

Note :

Your model may differ from the one shown.

0010534693

When set to “MED FAN”, fan motor runs at

med speed to blow out less stronger air.

When set to “MED COOL”,

air conditioner will

start cooling at med speed, blowing out less

stronger air.

This function will work only under cooling status.

HW-18LMA03(T3) HW-24LMA03(T3)

HW-18LMA13(T3) HW-24LMA13(T3)

CLOSE:to the left side;

OPEN:to the right side;

SELECTION OF THE INSTALLATION POSITION

THE ENCLOSED ACCESSORIES OF THE CONDITIONER

INSTALLATION PROCEDURES

PREPARATIONS BEFORE INSTALLATION

AIR CONDITIONER INSTALLATION

Fig.1

Wall

Water outlet flexible

pipe(provide by user)

1. Fix the prefabricated iron frame to stable position by expansible screws.

2. Put the whole machine with all the accessories installed,

on the iron frame. If there's water outlet flexible pipe, lead

it to needed position(see Fig.1).

3. Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to

prevent the entering of outer noise and the leaking of the coolness.

4. After installation of the conditioner, insert the power plug into the outlet and perform test-run.

Make the wall hole or window hole (see Fig.1)

Fig. 1

Width of the wall

Iron frame

MODEL A B

440mm 675mm

HW-18LMA03(T3)

HW-24LMA03(T3)

HW-18LMA13(T3)

HW-24LMA13(T3)

1,The air-conditioner is better installed in shadow or in a place

with short period of sunshine. In case the air-conditioner is

installed at the point exposed directly to the sunshine, it should

be protected from the direct sunlight as possible in order to

avoid the long time of direct sunlight otherwise its performance

will be lowered. (As illustrated in Fig. 1).

2. For the convenience of operation, it is

recommended that air-conditioner be installed at

least at the height of 1300 mm above the 760-

floor and no obstacles before it for a free airflow.

3.The shutters at both sides and the top of

air-conditioner should be protruded outdoors free

from being blocked by wall, window,ect.

4.The back of air-conditioner should be kept over

500mm from the obstacles (for example, wall,

etc.) (As illustrated in Fig. 2).

5.To have an efficient drainage, the back part of

the air-conditioner should be inclined downward

by 5-10mm (As illustrated in Fig. 3).

Install air-con at a place strong enough to support the unit.

Leave enough space around air inlet and outlet for better circulation.

Avoid places where flammable gas leaks.

Problems may occur if unit is installed in the following places:

Place where oil exists in the air including engine oil or seaside with

salt breeze blows and hot spring area with sulphurous gas in the air.

For longer and trouble-free operation of the unit, pay special attention to the following:

NOTES:

Outlet pipe fitting

Rubber lid

Name

Figure

1 1

Manual

(ONLY FOR REFERANCE)

cover

support

fig.1

>500mm

fig.2

5-10mm

fig.3

Cautions

Power cord: Be sure to use the exclusive power cord.

Always use at the rated voltage and with specfic air conditioning circuit

Change inst lation place: If r-con need to be c ged to anotheral ai han

place please contact the dealer, who sold you the unit.

1.Take out the conditioner and accessories from the package .

2.Choose one way from below two options on disposal of the condensed water.

Prepare unit for installation:

Generally there are two methods available on disposal of the condensed water:

Fig.1

Block the bottom plate hole of the conditioner

with rubber lid, install on theoutlet pipe fitting

back hole and let the condensing water flow from

the back hole of the conditioner. (See Fig.1 ) In

this method, the accumulated condensed water

in the bottom plate is hit by the fan onto the heat

exc nger, and rated and own outha evapo bl

from the mac ne. It can cool the heathi

exchanger adiator more quickly, and improve

the energy efficiency of the conditioner. But the

hitting noise by the fan at the outdoor side is

relatively large.

Method 1

Bottom plate hole

Rubber lid

Outlet pipe fitting

Fig.2

Bottom plate hole

Rubber lid

Back hole

Outlet pipe fitting

outlet pipe fitting

If necessary the above two methods can both

have extra pipe added on the

(available on the market).

Method 2

Block the back hole of the conditioner with

If the surrounding humidity is high:

rubber lid and install outlet pipe fitting

to the

bottom hole, which can make the condensed

water flow out from the bottom plate. (See Fig.2)

TROUBLESHOOTING

If problems can not be solved please pull out power plug and contact

your dealer.

Before calling for service.

Check the following points before calling for repairs or service.

Is plug firmly inserted?

Is there power failure?

Readjust power supply

Is thermostat switch

wrongly adjusted?

Readjust the thermostat.

Is there any direct

sunlight in the room?

Use curtain or blind.

Are doors or windows

left open? Shut doors and windows.

Are there any obstacles

blocking air inlet and

outlet?

Remove the obstacles.

Is there too much heat

source in the room?

Is air filter clogged?

Clean it.

Remove the heat source

Does fuse get burned?

Phenomenon SolutionCause or check points

Replace fuse.

Switch on the machine but it

does not work immediately.

If the machine is started after stop,it will need about 3 minutes

to re-start so as to prevent the fuse from break.

Switch on the machine but it

does not work.

The cooling effect is not good.

HW-18LMA03(T3)

HW-24LMA03(T3)

HW-18LMA13(T3)

HW-24LMA13(T3)

Sealed gasket

Specyfikacje produktu

Marka:	Haier
Kategoria:	nieskategoryzowany
Model:	HW-18LWA03/R2(T3)
Kolor produktu:	Szary
Typ wyświetlacza:	LED
Wysokość produktu:	101 mm
Szerokość produktu:	40.6 mm
Głębokość produktu:	15.1 mm
Waga produktu:	54 g
Wbudowane głośniki:	Tak
Technologia baterii:	Alkaliczny
Obsługiwane systemy operacyjne Windows:	Tak
Obsługiwane systemy operacyjne Mac:	Mac OS X 10.5 Leopard,Mac OS X 10.6 Snow Leopard,Mac OS X 10.7 Lion,Mac OS X 10.8 Mountain Lion,Mac OS X 10.9 Mavericks
Długość przekątnej ekranu:	1.43 "
Obsługiwane typy kart pamięci:	MicroSD (TransFlash),MicroSDHC
Pojemność pamięci wewnętrznej:	4096 MB
Rozdzielczość:	108 x 84 px
Obsługiwane formaty audio:	MP3,WAV,WMA
Wyjście na słuchawki:	Tak
Mikrofon:	Tak
Liczba baterii:	1
Standardowe rozwiązania komunikacyjne:	USB
Podświetlenie:	Tak
Ilość wbudowanych glosników:	1
Maksymalny czas nagrywania:	1000 h
Obsługiwane nośniki:	Pamięć wewnętrzna i karty pamięci flash
Materiały:	Plastik
Kolor podświetlenia:	Biały
Radio FM:	Nie
Wbudowany mikrofon:	Tak
Funkcja wstrzymania:	Tak
Odtwarzacz mp3:	Tak
Menu językowe:	DAN,DEU,DUT,ENG,ESP,FRE,ITA,POL,RUS,SLV
Połączenie z pc (personal computer):	Tak
Zgodne rodzaje baterii:	AAA
Rozmiar wyświetlacza:	27.6 x 23.9 mm
Tryb nagrywania:	High Quality (HQ),Long Play (LP),Pulse-code modulation (PCM)
Czas odgrywania:	30 h
Czas nagrywania w trybie LP:	1000 h
Czas nagrywania w trybie HQ:	257 h
Pasmo przenoszenia w trybie LP:	40 - 3000 Hz
Pasmo przenoszenia w trybie HQ:	40 - 13000 Hz
Moc wyjściowa:	150 mW
Średnica głośników:	18 mm
Wbudowana pojemność pamięci:	4 GB
Czas życia baterii przy nagrywaniu:	37 h
Liczba wiadomości w folderze:	200
Formaty nagrywania audio:	MP3,WAV,WMA