Instrukcja obsługi Haier HSU-13VXA21

Haier klimatyzacja HSU-13VXA21

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Haier HSU-13VXA21 (8 stron) w kategorii klimatyzacja. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
Please read this operation before using the manual air
conditioner. Keep this operation manual future for reference.
0010595326
1
2
5
7
6
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
HSU-12ANTIRUSTCOOL(INV)(TH)
HSU-12CLEANCOOL(INV)(TC)
HSU-12ENERGYCOOL(INV)(TR)
HSU-18ANTIRUSTCOOL(INV)(TH)
HSU-18CLEANCOOL(INV)(TC)
HSU-18ENERGYCOOL(INV)(TR)
HSU-18UVCOOL(SMART)(INV)(PB)
HSU-24ANTIRUSTCOOL(INV)(TH)
HSU-24CLEANCOOL(INV)(TC)
HSU-24ENERGYCOOL(INV)(TR)
HSU-10TSV13(DC)-SC
HSU-10TSP13(DC)-SC
HSU-12TSV13(DC)-SC
HSU-12TSP13(DC)-SC
HSU-18TSV13(DC)-SC
HSU-24TSV13(DC)-SC
HSU-10VTH21/10VTK21
HSU-13VTH21/13VTK21
HSU-19VTH21/19VTK21
HSU- 25VTH21
HSU-09VNR18
HSU-12VNR18
HSU-18VNR18
HSU-24VNR18
HSU-10VTH03
HSU-13VTH03
HSU-10VXA21
HSU-13VXA21
HSU-10XSV32
HSU-13XSV32
Remote controller
Parts and Functions
Indoor Unit
Outdoor Unit
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL
WIRING DRAIN HOSE
4
Display board
Actual inlet grille and Display board y vary from the ma one
shown he in t manual according the product to purchased
(adjust left and
Vertical blade
right air flow)
Air Purifying FilterInlet
(inside)
Emergency
Switch
Horizontal flap
Don't adjust it manually
Inlet grille
5
2
1
6
4
2
1
7
8
33 Outlet
Anion generator
(
inside,
only applicable for certain
1
Display board
2
3
Signal receiver
1
emp.display
2
3
Operation mode indicator
1
1. Mode display
Operation mode FANCOOL DRY
Remote controller
2.Signal sending
3.display SWING
4.display AN SPEED displayF
LO MED HI AUTO
circulated
5. LOCK display
6.TIMER OFF display
7.TIMER ON display
8.TEMP display Additional
functions display
Operation mode
Remote controller
QUIET TURBOSLEEP HEALTH
Loading of the battery
1
2
3
4
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
is in line with th e" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
Note:
When electronic-started type fluorescent lamp or change-
over
type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receiving
the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batteries have been used up Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and
reload several minutes later.
(adjust up and down air flow
1
2
3
4
5
9
10
11
12
13
14
15
16
17
8
22
23
24
25
19
20
21
18
7
6
SLEEP
TIME
ON
SWING
EXTRA
FUNCTION
LOCK LIGHT R E S E T
MODE
SLEEPI FEEL
HEALTH TIMER
SELF
CLEAN
HEALTH
AIRFLOW
1
2
3
4
5
9
10
11
12
13
14
15
16
8
22
23
24
25
19
20
21
18
7
6
17
1. Mode display
Operation mode FANCOOL DRY
Remote controller
LO MED HI AUTO
circulated
Operation mode
Remote controller
QUIET TURBOSLEEP HEALT H
Be sure that the loading
26
9.TURBO/QUIET button
10.SELF CLEAN button
11.COOL button
12.SWING LEFT/RIGHT button
(only applicable for certain models)
13.FAN SPEED button
14.HEALTH button/DRY button
(Refer to the actual remote control layout
for specific functions)
15.SLEEP button
16.LOCK button
17.LIGHT button
18.POWER ON/OFF button
19.DRY button/ECO button
(Refer to the actual remote control layout
for specific functions)
20.TEMP button
21.SWING UP/DOWN button
22.TIME OFF/ON button
23.EXTRA FUNCTION button
Function :FAN---Healthy airflow position1---
Healthy airflow position2
Function :FAN --- Health
24.CONFIRM/CANCEL button
Function :Setting and cancel to the timer
and other additional functions.
25.RESET button
When the remote controller appears
abnormal,use a sharp pointed article to
press this button to reset the remote.
9.TURBO/QUIET button
10.SELF CLEAN button
11.MODE button
12.SWING UP/DOWN button
13.FAN SPEED button
14.I FEEL button
15.SLEEP button
16.LOCK button
17.LIGHT button
18.POWER ON/OFF button
19.ECO button
20.TEMP button
21.SWING LEFT/RIGHT button
(only applicable for certain models)
22.HEALTH AIR FLOW button
23.CONFIRM/CANCEL button
Function :Setting and cancel to the
timer and other additional functions.
24.TIMER button
25.HEALTH button
26.RESET button
When the remote controller appears
abnormal,use a sharp pointed
article to press this button to reset
the remote.
5. LOCK display
6.TIMER OFF display
7.TIMER ON display
8.TEMP display Additional
functions display
2.Signal sending
3.display SWING
4.display AN SPEED displayF
CONFIRM
CANCEL
TURBO/QUIET
LOCK LIGHT R E S E T
TIME
OFF
CONFIRM
CANCEL
COOL SELF
CLEAN
TURBO/QUIET
Operation
Air Flow Direction Adjustment
Basic Operation
Remote controller
Emergency erationoperation and test op
Emergency Operation:
Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:
It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.
Press FAN button. For each press, fan sp d ee
follows:
Remote controller:
Press button
Eve time the on pressed, temp.settingry butt is
increase 1oC,if pt pressed, will increaseke de it
rapidly
Eve time the on pressed, temp.settingry butt is
decrease 1
oC,if will kept depressed, it
decrease rapidly. Select a desired
temperature.
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
/
Display
circulated
changes as
LOW MED HI AUTO
Remote
Controller Note
In DRY mode , when room temperature becomes lower
th
an temp.setting+2o C, unit will run intermittently at
LOW speed regardless of FAN setting.
In FAN operation mode , the unit will not operate in COOL or
HEAT mode but only in FAN mode, AUTO is not available in
FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.
Operation
Mode
DRY
COOL
FAN
Test operation:
Test operation switch is the same as emergency switch.
Service perso elnn
Continue to press the test operation
switch for more than 5 seconds.After
you hear the "Pi" sound twice,release
your finger from the switch: the cooling
operation starts with the air flow speed "Hi".
Under this operation mode,the fan motor of indoor
unit will run in high speed.
Pi Pi
Room
temperature
Designated
temperature
Timer
mode
Fan
speed
Operation
mode
Above 23oC 26oC AUTO COOL
No
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
at air outlet if all vertical louvers are adjusted to left or right.
It is advisable not to keep horizontal flap at downward position
for a long time in COOL or DRY mode ,otherwise, condensate
water might occur.
1.Status display of air flow
2.Left and right air flow adjustment
Pos.1 Pos.2 Pos.3 Pos.4
Pos.5 Pos.6
For each press of button, remote controller
displays as follows :
remote controller:
Vertical apfl
Pos.1
(Auto swing)
Pos.2 No initial state disaplayed on controller, theremote
vertical flap will be fixed on the current position
2
Press button to enter additional options, when
enter to FAN function.
1. Start unit
Press ON/OFF
Start unit
2. Select operation mode
COOL button:Cooling mode
DRY button: Dehumidify
mode
3. Select temp. setting
In COOL mode,the AC unit will emit Cool air according
to the remote setting on the temperature display The
Setting temperature is adjustable
Pi
Note: In some model: The remote the button , But has
the AC doesn’t have the left and auto adjustment right air flow
function change the direction of ivertical, this condition blades
manually.
the function only applicable for certain models)(
Cautions:
MODE

Specyfikacje produktu

Marka: Haier
Kategoria: klimatyzacja
Model: HSU-13VXA21

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Haier HSU-13VXA21, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje klimatyzacja Haier

Haier

Haier QPCA11YBMW Instrukcja

8 Października 2024
Haier

Haier QPFA08YBMW Instrukcja

8 Października 2024
Haier

Haier QHEC05AC Instrukcja

8 Października 2024
Haier

Haier QHEK12AC Instrukcja

8 Października 2024
Haier

Haier QHEK10AC Instrukcja

8 Października 2024
Haier

Haier QHEK14AC Instrukcja

8 Października 2024
Haier

Haier QHNG10AA Instrukcja

8 Października 2024
Haier

Haier QHNG08AA Instrukcja

8 Października 2024

Instrukcje klimatyzacja

Najnowsze instrukcje dla klimatyzacja

LG

LG HS-H076QPA0 Instrukcja

15 Października 2024
Klarstein

Klarstein Vita Pure 2G Instrukcja

15 Października 2024
Gree

Gree ETAC-15HP265V20B Instrukcja

15 Października 2024
Qlima

Qlima P 126 Instrukcja

14 Października 2024
Mitsubishi

Mitsubishi MSZ-CB22VA Instrukcja

14 Października 2024
Suntec

Suntec Motion 90+ Instrukcja

14 Października 2024
Danby

Danby DTAC120B1WDB Instrukcja

14 Października 2024
Amana

Amana PTC093K35AXXX Instrukcja

14 Października 2024
Amana

Amana AMAP121AB-2 Instrukcja

14 Października 2024