Instrukcja obsługi Hager TXM632C

Hager przełącznik TXM632C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager TXM632C (2 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

6LE002527A

TYM632C

Output 12gang shutter/blind

230V~

TXM632C

Output 12gang shutter/blind

230V~

Bn?.:

6LE002527A1

Safety instructions

Electrical equipment may only be installed and

assembled by a qualied electrician in accord-

ance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

Hazard due to electric shock. Disconnect be-

fore working on the device or load. Take into

account all circuit breakers that supply danger-

ous voltages to the device or load.

Connect one motor per output only. If several

motors are connected, motors or device might

be destroyed.

Use drives with mechanical or electrical nal

position switches only. Check nal position

switches for correct adjustment. Observe mo-

tor manufacturer's data. The device can be

damaged.

Do not connect any three-phase motors. The

device can be damaged.

Risk of injury. Use the device to control blind

and shutter drives or awnings only. Do not

switch any other loads.

Observe the motor manufacturer's data regard-

ing change-over time and max. switch-on time

(ED).

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

C1/C7 C3/C9 C5 /C11

C2/C8 C4/C10 C6/C1 2

3 4 5 6 7 8 9 101 2

N L

L L

230V 50/60 Hz

L L CC6C4C2

18 19 20 2 1 22 23 2 4 25 26

auto 1

auto 2

(1)

(2) (3)

(4) (5)

(6)

(3)

(7)

Figure 1: Device overview

(1) Slide switch / 1/ 2auto1/auto2

(2) KNX bus connection terminal

(3) Connections of loads

(4) Labelling eld with cover

(5) Illuminated programming button

(6) Operation button for manual operation per

output with status LED

(7) Mains power supply connection

Function

System information

This device is a product of the KNX system and

corresponds to the KNX guidelines. Detailed

specialised knowledge obtained from KNX training

courses

is required for understanding. The planning, instal-

lation and commissioning of the device is carried

out with the help of KNX-certied software.

Systemlink commissioning:

The function of the device is software-depend-

ent. The software is to be taken from the product

database. You can nd the latest version of the

product database, technical descriptions as well as

conversion and additional support programmes on

our website.

Easylink commissioning:

The function of the device is conguration-de-

pendent. The conguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Precongured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The device is used to control motor-operated build-

ing ttings such as shutters and blinds via the KNX

bus. The device has 12 outputs from which each

output can be activated independently.

Correct use

- Switching electrically operated motors of 230 V

AC for blinds, shutters, awnings and similar

hangings

- Mounting on DIN rail according to DIN EN

60715 in the distribution box

Product characteristics

- independent outputs, activation via KNX bus

- Status display of the outputs on the device

- manual activation of the outputs on the device

possible, building site operation

- Position can be started directly

- 3 Alarms

- Scene function

- Forced position by higher-level controller

- Connection of various external conductors

possible

- Slat position directly controllable

Operation

Manual operation switch on/off

Bus and mains power supply are present.

zPush switch (1) to position 1/ 2.

Manual operation is switched on, the outputs

can be controlled using the operation buttons

(6) independently of each other.

1 switches on the control of the outputs

C1 C6 .. .

2 switches on the control of the outputs

C7 C12 .. .

During manual operation, the controller is deac-

tivated via the KNX bus.

Systemlink commissioning:

Depending on the programming, the manual

operation is activated permanently or for a time

period congured via the application software.

If the manual operation is blocked via the appli-

cation software, no activation takes place.

Or:

zMove switch (1) to position .auto1/auto2

The manual operation is switched off. Operation

takes place solely via the KNX bus. The output

adopts the position predened by the bus con-

troller. The switching status is displayed via the

status LED of the operation button (6).

auto 1 C1 displays the status of the outputs ..

C6.

auto 2 C7 displays the status of the outputs ..

C12.

Operating outputs in manual operation

Operation takes place per output by briey pressing

the operation button repeatedly (table1).

Status Behaviour when

button pressed briey

Output is in idle

state,

status LED of the

button (6) is off.

Movement operation starts.

Status LED of button (6)

lights up.

Output active,

status LED of the

button (6) lights

up.1)

Movement operation stops,

LED goes out.

The LED lights up red during upward travel and green

during downward travel.

Table 1: Manual operation

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

CAUTION!

Risk of destruction if parallel connec-

tion of several motors on one output!

Final position switches could fuse

together. Motors, hangings and the

device may be destroyed!

Only connect one motor per

output!

2 Hager 12.16 - 6LE002527AHager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com

Installing the appliance

Observe temperature range. Provide sufcient

cooling.

zMount device onto DIN rail in accordance with

DIN EN 60715.

Connecting the device (Figure 2)

The installation circuit must be protected via circuit

breaker 10 A.

zConnect bus cable via connecting terminal (2).

zConnect mains voltage (7).

zConnect motors.

Start-up

Systemlink: Loading physical address and

application software

The switch (1) is in .auto1/auto2

zSwitch on bus voltage.

zPress programming button (5).

The button lights up.

If the button does not light up, no bus voltage is

present.

zLoad the physical address into the device.

Status LED of the button goes out.

zLoad application software.

zNote down the physical address on the labelling

eld (4).

Easylink:

Information on the system conguration can be

taken from the extensive description of the service

module easylink.

Starting up the device

zSwitch on mains voltage on the outputs.

zSwitch on mains supply.

Determine operation time and slat adjusting

time

In blind/roller shutter operation, the operation time

for positioning the sunshade is important. The posi-

tion is calculated based on the operation time. The

slat adjusting time for slat blinds, determined by

the design, is part of the total operation time. The

opening angle of the slats is therefore set as oper-

ation time between opened and closed position.

The operation time for UP is normally longer

than the operation time for DOWN and must be

measured separately if necessary.

zMeasure UP and DOWN operation time of the

hanging.

zMeasure slat adjusting time between OPEN

and CLOSED.

zEnter measured values into the parameter set-

ting – ... or .running time slat step time

Functional test

The functionality of the outputs is displayed via the

status LED of the operation button (6).

Appendix

Technical data

KNX medium TP 1

Conguration mode S-Mode, E-controller

easy link

Rated voltage KNX 30 V SELVs

Own consumption on the KNX bus:

- typical 7 mA

- in standby 5 mA

Auxiliary voltage 230V~ +10%/-15%

240V~ +/-6%

Mains frequency 50/60 Hz

Power dissipation maximum 3 W

Own consumption on mains:

- maximum 5 W

- in standby 0.2 W

Breaking capacity µ 4A AC1 230V~

Switching current at cos Φ = 0.6 max. 4 A

Upstream protection: circuit breaker 10 A

Operating altitude max. 2000 m

Degree of contamination 2

Surge voltage 4 kV

Degree of protection of housing IP 20

Degree of protection of housing

under front panel IP30

Impact protection IK 04

Overvoltage class III

Operating temperature -5°C à + 45°C

Storage/transport temperature -20°C à + 70°C

Maximum switching cycle

rate at full load 6 switching cycle/minute

Connection capacity 0.5 mm² … 6 mm²

Dimension 10 TE, 10 x 17.5 mm

Troubleshooting

Manual operation not possible

Cause 1: Switch (1) not moved to 1/ 2.

Move switch to 1/ 2.

Cause 2: Manual operation has not been enabled

(Systemlink).

Enable manual operation via application soft-

ware.

Bus operation is not possible

Cause: Bus voltage is not present.

Check bus connection terminal for correct

polarity.

Check bus voltage by briey pressing the pro-

gramming button (5), red LED lights up if bus

voltage is present.

If mains voltage is available without bus voltage

- red LED of the programming button (5) blinks.

Cause 2 : Manual operation is active. Switch (1) is

in position .1/ 2

Move switch (1) to position .auto1/auto1

Shutters/blinds do not move to the nal

position

Cause: Operation time for the shutters/blinds set

incorrectly.

Check operation times. Measure again and

reprogram if necessary.

Correct Disposal of This product

(Waste Electrical & Electronic

Equipment).

(Applicable in the European Union and other European

countries with separate collection systems).

This marking shown on the product or its literature

indicates that it hould not be disposed with other

household wasted at the end of its working life. To prevent

possible harm to the environment or human health from

uncontrolled waste disposal, please separate this from

other types of wastes and recycle it responsibly to

promote the sustainable reuse of material resources.

Household users should contact either the retailer where

they purchased this product, or their local government

oce, for details of where and how they can take this item

for environmentally safe recycling.

Business users should contact their supplier and check

the terms and conditions of the purchase contract. This

product should not be mixed with other commercial

wastes of disposal.

Usable in all Europe

and in Switzerland

C1/C7 C3/C9 C5/C11

C2/C8 C4/C10 C6/C12

3 4 5 6 7 8 9 10 11 12 13 14 15 16 171 2

N L

L L LC9 C11

230V 50/60 Hz

L L LC10 C12C8C6C4C2

18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

auto 1

auto 2

Fig 2: Device connection

Specyfikacje produktu

Marka:	Hager
Kategoria:	przełącznik
Model:	TXM632C
Kolor produktu:	Szary
Wysokość produktu:	90 mm
Zakres temperatur (eksploatacja):	-5 - 45 °C
Stopień ochrony IP:	IP20
Liczba dołączonych produktów:	1 szt.