Instrukcja obsługi Hager TXB601B

Hager nieskategoryzowany TXB601B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager TXB601B (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

TYB601B

Output 1gang 10 A,

ﬂush mounted

TXB601B

Output 1gang 10 A,

ﬂush mounted

Bn,.:

Safety instructions

Electrical equipment may only be installed and

assembled by a qualied electrician in accord-

ance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

Hazard due to electric shock. Disconnect

before working on the device or load. Take into

account all circuit breakers that supply danger-

ous voltages to the device or load.

Hazard due to electric shock. The device is not

suited for safe disconnection of the mains sup-

ply.

Hazard due to electric shock on the SELV or

PELV installation. Do not connect any loads for

low voltage SELV, PELV or FELV together.

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

KNX+ /RD

KNX- /BK

(1)

(2)

(3)

Figure 1: device overview

(1) Illuminated button for manual operation/

programming button

(2) Connection of load(s)

(3) KNX bus connection cable

Function

System information

This device is a product of KNX system and corre-

sponds to the KNX guidelines. Detailed specialised

knowledge obtained from KNX training courses is

required for understanding. The planning, installa-

tion and commissioning of the device is carried out

with the help of KNX-certied software.

S-Mode start-up

The function of the device is software-depend-

ent. The software is to be taken from the product

database. You can nd the latest version of the

product database, technical descriptions as well as

conversion and additional support programmes on

our website.

E-Mode start-up

The function of the device is conguration-de-

pendent. The conguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Precongured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The device receives telegrams from sensors or

other controllers via the KNX installation bus and

switches electrical loads with its relay contact.

Correct use

- Switching of electrical loads

potential-free contact.

- Installation into wall box according to

DIN 49073 (use deep box) or junction box sur-

face-mounted/ush-mounted.

Product characteristics

- Time switching functions.

- manual activation of the outputs on the device

possible, building site operation.

- Status display of the outputs on the device.

- Scene function.

- Forced position by higher-level controller.

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

Connecting and installing the device

CAUTION!

Impermissible heating if the load of

the device is too high!

The device and the connected cables

may get damaged in the connection

area!

Do not exceed the maximum current

carrying capacity!

CAUTION!

When connecting the bus/extension

units and mains voltage wires in a

common wall box, the KNX bus cable

might come into contact with the

mains voltage.

The safety of the entire KNX

installation is at risk. Persons could

also get an electric shock even on

remote devices.

Do not place bus/extension units and

mains voltage terminals in a common

terminal compartment. Use a wall box

with a rm partition or separate boxes

(Figure 2).

KNX+ /RD

KNX- /BK

KNX+ /RD

KNX- /BK

KNX+ /RD

KNX- /BK

SELV

Figure 2: installation with separate terminal com-

partment

6LE000363C1

6LE000363C

230 V v

230 V withv

KNX+ /RD

KNX- /BK

Bus

30 V DC

10 A

Fig 3: device connection 1gang

Observe installation regulations for SELV voltage.

Maintain a minimum distance of 4 mm between

mains voltage and bus wires.

The installation circuit must be protected via circuit

breaker 10 A.

zConnect bus cable via connecting terminal.

zConnect load to the load connecting terminals

(2).

zPlace device into the installation box.

Start-up

S-mode: loading the physical address and

applicatiln software

zSwitch on bus voltage.

zPress programming button (1).

The button lights up.

If the button does not light up, no bus voltage is

present.

zLoad the physical address into the device.

Status LED of the button goes out.

zLoad application software.

zNote down the physical address on the device.

E-mode

Information on the system conguration can be

taken from the extensive description of the service

module easylink.

Start up the device

zSwitch on mains voltage on the outputs.

Switch test mode on/off

The device is connected. Bus voltage and switch-

ing voltage are present.

zKeep button (1) pressed > 5 s with a pointed

object until it ashes green.

The device is in test mode/manual operation.

Or with manual operation switched on

zKeep button (1) pressed > 5 s until it ashes

green 3 times.

The device is in normal operation.

After approx. 5 min. without any further

operation, the device exits manual operation

automatically.

Operating output in test mode

Operation takes place by briey pressing a button

repeatedly (1) .

The device is in test mode. The button ashes

green until the rst operation.

zPress the button (1) for a short time.

The output changes its switching state.

Resetting the device to the factory settings

The device provides the possibility of restoring the

factory setting via a programming button.

The programming is lost after resetting to the

factory setting. Activation via the bus is no

longer possible.

zHold down the button S1/Addr. (1) for > 10 s

until it ashes red.

The device is reset to the factory setting.

Appendix

Usable in all Europe

and in Switzerland

Hager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com 6LE000363C2

Technical data

Supply voltage KNX 21 32 V SELVs

Breaking capacity μ 10 A AC1 230 V~

Minimum switching current 10 mA

Operating altitude max. 2000 m

Degree of contamination 2

Surge voltage 4 kV

Degree of protection of housing IP20

Impact protection IK 04

Overvoltage class III

Upstream protection circuit breaker 10 A

Communication Media TP

Conﬁ guration mode S mode - Easy link controller

Ambient temperature -5°C +45°C

Storage/transport temperature -20°C +70°C

Maximum switching cycle rate at full load:

20 switching cycle/minute

Connection capacity 0.75 mm² 2.5 mm²

Installation type ﬂ ush-mounted installation switch /

ﬂ ush-mounted electronic /

ﬂ ush-mounted/surface-mounted junction box

Dimensions 44 x 43 x 22.5 mm

Own consumption on the KNX bus

Typical 7 mA

In standby 5 mA

Incandescent lamps 600 W

Halogen lamps 600 W

Conventional transformer 600 VA

Electronic transformer 600 W

Fluorescent lamps

-without ballast 600 W

-with EVG 6 x 58 W

Energy-saving lamps 2 x 15 W

LED lamps 2 x 15 W

Troubleshooting

Test mode not possible. Red programming LED

lights up.

Cause: push-button (1) was pressed too short.

Short press on push-button, red LED goes out.

Press push-button again ( > 5 s).

Bus operation is not possible.

Cause 1: bus voltage is not present.

Check bus connection terminal for correct

polarity.

Check bus voltage by brieﬂ y pressing the

programming button (1), red LED lights up if bus

voltage is present.

Cause 2: device was reset to the factory setting

Repeat programming and start-up.

Correct Disposal of this product (Waste Electrical &

Electronic Equipment).

(Applicable in the European Union and other European

countries with separate collection systems).

This marking shown on the waste or its literature indicates that it

should not be disposed with other household wasted at the end

of its working life. To prevent possible harm to the environment or

human health from uncontrolled waste disposal, please separate

this product from other types of wastes and recycle it responsibly

to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they pur-

chased this product, or their local government office, for details of

where and how they can take this device for environmentally safe

recycling.

Business users should contact their supplier and check the terms

and conditions of the purchase contract. This product should not be

mixed with other commercial wastes of disposal.

Specyfikacje produktu

Marka:	Hager
Kategoria:	nieskategoryzowany
Model:	TXB601B
Kolor produktu:	Szary
Wysokość produktu:	44 mm
Zakres temperatur (eksploatacja):	-5 - 45 °C
Stopień ochrony IP:	IP20
Liczba dołączonych produktów:	1 szt.