Instrukcja obsługi Hager JKD101SPD


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager JKD101SPD (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
JK 1 Surge ProtectionD Instructions
Instruction leaflet for fitting 125A Surge
Protection in Power and lighting boards
JK 101SPDD
JK 102SPDD
Pozidrive
PZ2
2.5mm
8mm
Socket
GB
1ZD0 - Issue 0 -1869199
ZD00869ZD0869
Clip the 4 module surge protection
device to the dinrail next to the incomer.
Fit the 3 KRN199 terminal block's to the
first 3 phases on the left hand side of
the busbar stack as shown above and
torque to 3.5Nm.
Secure the 3 brown cables to the
terminals of the Surge protection
device and the corresponding KRN
devices L1/L2/L3 and torque to
3.5Nm.
Secure the Neutral cable to the Surge
device to 3.5Nm and use the M5 hex
head screw with washers to secure
the ring terminal to the neutral bar
next to the factory fitted neutral and
secure to 3.5Nm.
1. 1 x Type I+II or Type II Surge
Protection device
2. 1 x Copper Earth Link
3. 2 Hex head Earth screws x
4. 3 x KRN199 Terminal block
5. 1 x ZB0220 M6 Carp Nut
6. 1 x Neutral link
7. 3 x L1/L2/L3 Phase links
8. 1 x M5 Hex head screw & washers
Parts list:
The device may only be connected and installed by an electrically skilled person. National standards and safety regulations must be
observed.
The device must be checked for external damage prior to installation. If any damage or other defects are detected in this check, the
device must not be installed.
Its use is only permitted within the limits shown and stated in the installation instructions.
Opening or otherwise tampering with the device invalidates the warranty.
Place the copper earth component into
the bottom two cage terminals of the
surge protection device and secure to
3.5Nm.
Use the 2 high torque screws provided to
then secure the earth link to the base at
3.5Nm.
KRN199
KRN199
KRN199
TI+T2 SPD
'Ensure that when re-fitting the shroud that the left hand side is cut out to avoid clashing with the Surge protection cables'


Specyfikacje produktu

Marka: Hager
Kategoria: nieskategoryzowany
Model: JKD101SPD

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hager JKD101SPD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nieskategoryzowany Hager

Hager

Hager VS418PZF Instrukcja

15 Sierpnia 2024
Hager

Hager VS318PZF Instrukcja

15 Sierpnia 2024
Hager

Hager VS218PZF Instrukcja

15 Sierpnia 2024
Hager

Hager TN204S Instrukcja

15 Sierpnia 2024
Hager

Hager TN206S Instrukcja

15 Sierpnia 2024
Hager

Hager EH171A Instrukcja

15 Sierpnia 2024
Hager

Hager EG203 Instrukcja

14 Sierpnia 2024
Hager

Hager EG403E Instrukcja

14 Sierpnia 2024
Hager

Hager M-RG404020 Instrukcja

14 Sierpnia 2024
Hager

Hager 80262160 Instrukcja

14 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024