Instrukcja obsługi Hager 85656185

Hager nieskategoryzowany 85656185

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager 85656185 (7 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/7

KNX radio wall-transmitter 1gang/2gang at quicklink

Page 1/7

6W-5830 08-2012

KNX radio wall-transmitter 1gang/2gang at quicklink

Order no.: 8565 p1-x2 xx

KNX radio wall-transmitter 1gang/2gang at solar quicklink

Order no.: 8565 p1-x1 xx

Operating instructions

1. Safety instructions

Electrical equipment may only be installed and assembled by a qualied electrician in

accordance with the relevant installation standards, guidelines, regulations, directives,

safety and accident prevention regulations of the country.

Failure to comply with these instructions may result in damage to the device, re or other

hazards.

Button cells do not belong in children's hands! If button cells are swallowed, seek imme-

diate medical assistance.

Danger of explosion! Do not throw batteries in re.

Danger of explosion! Do not recharge batteries.

The radio transmission is not suitable for safety or alarm applications.

These instructions are an integral component of the product and must be retained by the

end user.

2. Design and layout of the device

(1)

(2)

(3)

(5)

(6)

(8)

(1)

(2)

(4)

(5)

(7)

(8)

Figure 1: Design and layout of the device

(1) Supporting plate

(2) Frame (not within scope of delivery)

(3) Exemplarily Radio wall-transmitter 1gang at solar quicklink

(4) Exemplarily Radio wall-transmitter 2gang at quicklink

(5) Screw for dismantling protection

(6) Button design cover 1gang

(7) Button design cover 2gang

(8) Transmission status LED

KNX radio wall-transmitter 1gang/2gang at solar quicklink

Page 2/7

6W-5830 08-2012

3. Function

System information

This device is a product of the quicklink system, in which installation devices communicate via

radio signals.

Quicklink stands for a conguration mode in which the function-related connection between

transmitters and receivers is set on the device through buttons and displays without further

tools.

All devices congurable by quicklink can be operated together in one system.

This device complies with the R&TTE directive 1999/5/EG. The declaration of conformity and

further system information can be found on our internet site www.berker.de.

The device may be operated in all EU and EFTA states.

Correct use

–Flat surface installation and extension of combinations.

–Only suitable for use in indoor areas with no drip and no spray water.

–The device has been laid out for smaller applications in which a maximum 20 devices are

allocated.

Product characteristics

–Functions for remote control, scenes, control switches via radio signals.

–Transmission status LED as display of radio reception; as required, when battery is too

weak or a conguration is absent.

4. Operation

Allotting of channels to inputs of wall-transmitter

Figure 2: Allotting of channels to inputs

Transmit radio command

The push-button operation areas are freely congurable; operation is dependent on the congu-

ration (Table 3).

Press a push-button operation area, e.g. 1, to send a radio command.

The transmission status LED (8) lights up to conrm.

KNX radio wall-transmitter 1gang/2gang at solar quicklink

Page 3/7

6W-5830 08-2012

Transmission status LED display

After operation, the transmission status LED on the 1gang wall-transmitter lights up through a

lens and on the 1gang wall-transmitter and on the 2gang wall-transmitter, through the gap bet-

ween the two push-buttons.

Transmission status LED Severity

Blinking orange Button not congured

Blinking green / blinking green Radio command sent / radio command received

1 x blinking green Radio command sent to timer

1 x blinking green / 1 x blinking

red

Radio command sent / radio command not received (with at

least 1 device)

Red, ickering for 2 seconds Battery weak; replace

Table 1

5. Information for electricians

Overview of the operating elements beneath the design cover

(10)

(9)

Figure 3: Wall-transmitter with battery

(10)

(9)

(11)

Figure 4: Wall-transmitter solar

(9) Press-activation point of the push-button operation area

(10) cfg cfg input with LED or transmission status LED

(11) Solar cells

Specyfikacje produktu

Marka:	Hager
Kategoria:	nieskategoryzowany
Model:	85656185
Kolor produktu:	Czerwony
Typ produktu:	Model samochodu sportowego
Głębokość produktu:	198 mm
Model:	Model pojazdu lądowego
Zalecany wiek (min):	12 lat(a)
Skala:	1:24
Nieodpowiedni dla dzieci poniżej 3 r.ż.:	Tak
Oryginalna nazwa modelu:	LaFerrari
Rodzaj konstrukcji:	Zestaw montażowy
Motyw:	LaFerrari