Instrukcja obsługi Hager 85345126

Hager nieskategoryzowany 85345126

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager 85345126 (3 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

KNX radio motion detector comfort

1.1 m quicklink

Order no. 8534 51 ..

KNX radio motion detector comfort

2.2 m quicklink

Order no. 8534 61 ..

Configuration instructions

Berker GmbH & Co. KG

Zum Gunterstal

66440 Blieskastel, Germany

Tel.: + 49 6842 945 0

Fax: + 49 6842 945 4625

e-mail: info@berker.de

www.berker.com

04/2022

6LE007947A

KNX radio conﬁ guration

quicklink

The radio conﬁ guration sets up the functional

connection between commanding (transmitters)

and function-executing (receivers) radio compo-

nents. Thus, central, group, extension unit and

time controls, for example, can be implemented in

a wireless manner.

The following can be conﬁ gured:

-The local operation of the load connected to the

insert

- Radio commands to control other receivers

- Functions which are executed when the radio

commands are received

►See Table 5

For conﬁ guration by means of Hager connec-

tion device TX100 or ETS, additional functions

are available (see operating instructions for

TX100 or application description for ETS).

Conﬁ guration to control the load connected to the

insert via reception of a radio command.

As an example, the conﬁ guration of a wall-trans-

mitter and a radio motion detector as receiver is

described (Table 6).

fct LED

display

Conﬁ gurable

functions

Function resulting from transmitter operation,

notes

On switch insert

On dimmer insert

ON/OFF 1)

ON/OFF,

dim UP/

DOWN

Short button-press: Switch ON/OFF

Long button-press: Dimming, reverse dimming direc-

tion per actuation

ON,

dim UP

Short button-press: Switch ON

Long button-press: Dim UP to maximum brightness

OFF

OFF,

dim

DOWN

Short button-press: Switch OFF

Long button-press: Dim DOWN to minimum bright-

ness

Scene 1

Receiver is allocated to a scene due to the conﬁ gura-

tion of the function.

Short button-press: Short button-press: Recall the

saved state of the connected load for the scene

Scene 2

Timer

Switch ON for the set switch-on time

Factory setting = 3 min

ON/OFF

(switch/push-button)

Closing of the activating contact switches the load

ON, opening of the contact switches the load OFF.

Forced mode ON

Switches the load with higher priority to the appropri-

ate state. Execution of other commands is only possi-

ble after resetting the forced command.

Forced mode OFF

Presence

simulation 1)

Activates/deactivates execution of presence simula-

tion (See Activating/deactivating presence simulation).

Master-Slave

Is used to extend the detection area. Receives

switch-on commands in case of motion detection in

the detection area of the transmitter (Slave). Switches

the lighting ON for the set delay time.

The brightness evaluation only takes place on the

master, the slave only detects motion.

Can only be conﬁ gured between radio motion

detectors.

Cancel

No function

Assignment to transmitter is deleted

Execution of the receiver function and local motion detector function have the same priority:

–If the transmitter was ﬁ rst switched on/oﬀ and then motion was detected afterwards, then the motion detector will

override the transmitter command

–If motion was detected and thereafter, during the delay time, the system is switched on/oﬀ via the transmitter, then

the transmitter will override the motion detector

Only with KNX radio motion detector on power supply for KNX radio application module as transmitter

Table 5: Conﬁ gurable functions

Operation

Result

Start conﬁ guration



Press the button on the wall-transmitter cfg

brieﬂ y.

If there is no further activation, the

conﬁ guration is automatically ended after 10

minutes.

The LEDs on the wall-transmitter and the radio cfg

motion detector light up in red colour.

150

90°

...

45° 45°

...

90°

fct

cfg

All the receivers within radio range also display the

conﬁ guration mode.

Select transmitter button



Brieﬂ y press the press-activation point on the

wall-transmitter, which should activate the

function.

The cfg LED on the wall-transmitter ﬂ ashes for 1

second.

If conﬁ gured already fct LED of the motion detector

indicates the currently conﬁ gured function.

Select function on receiver



Repeatedly apply short presses to the fct

button on the motion detector until the desired

function is displayed (Table 5).

150

90° 45° 90° ...

fct

cfg

After each operation, the fct LED indicates the

function.

If the transmitter button has already been

conﬁ gured with a function in a diﬀ erent receiver

and/or the conﬁ gured function is part of a group

control, only this function can be conﬁ gured.

To change a function, the existing conﬁ guration

must be deleted and the new one needs to be

conﬁ gured.

Conﬁ rm function on receiver



To conﬁ rm, keep the button pressed for fct

more than 2 seconds.

150

90° 45° 90° ...

fct

cfg

> 2 s

The cfg LED ﬂ ashes during the saving process

(approx. 5 s). The LED conﬁ rms the function fct

selection by displaying the corresponding colour.

150

90° 45° 45° 90° ... ...

fct

cfg

Rapid ﬂ ashing of the cfg LED indicates a

combination that is not possible or an error.

Completing the conﬁ guration



Brieﬂ y press the cfg button on the wall-

transmitter again.

The LEDs on the wall-transmitter, on the motion cfg

detector and on all receivers within radio range go

out. The function is conﬁ gured.

Table 6: Conﬁ guration of the function for the KNX radio motion detector

Conﬁ guration of KNX radio motion detector as a receiver

Conﬁ guration of KNX radio motion detector as

a transmitter

If the radio motion detector is operated as a trans-

mitter, it can support the following functions for

receivers. The speciﬁ c function can vary depend-

ing on the receivers used:

ON/OFF (delay time)

Preconﬁ gured command in Automatic

mode: Motion detection with simultaneous

undershooting of the brightness threshold

switches the load ON and, after the delay

time has elapsed, it switches the load

OFF. The delay time elapses in the motion

detector and is permanently set (3 min).

Timer

Motion detection with simultaneous

undershooting of the brightness threshold

switches the load ON and, after the switch-

on time has elapsed, it switches the load

OFF. The switch-on time elapses in the

receiver and can be adjusted through

conﬁ guration.

The radio motion detector must be attached to

a switch insert or dimmer insert. If the radio

motion detector is mounted on a power supply

for KNX radio application modules, then it can

only be conﬁ gured as a transmitting extension

unit (slave) (see Executing a master-slave con-

ﬁ guration).

As an example, there is a description of conﬁ gur-

ing the radio motion detector with receivers below,

for which the LED and cfg fct LED provide the

supported displays (Table 7). Diﬀ erent conﬁ gura-

tion displays, such as for receivers with a display,

are provided in the instructions for the receiver.

Executing the master-slave conﬁ guration

If the radio motion detector is attached to a power

supply for radio application modules, then it can

only be conﬁ gured as a transmitting extension

unit (slave) to a radio motion detector on switch or

dimmer insert (Table 8).

The slave motion detector sends a pulse in case

of motion detection in its detection area. Upon

receiving this pulse, the master switches on for

the delay time, if the set brightness threshold is

undershot. Delay time and brightness threshold

are determined by the master.

Deleting a conﬁ guration

To delete a conﬁ gured receiver or the local opera-

tion, perform the conﬁ guration again.

Start conﬁ guration (see Conﬁ guration of radio

motion detector as a receiver).

If necessary, select transmitter button.

The select transmitter button step does not ap-

ply for radio motion detectors as transmitters.

Select function on receiver: Select the Delete

function on the receiver and conﬁ rm the func-

tion on the receiver.

Completing the conﬁ guration: Brieﬂ y press the

cfg button on the transmitter.

Conﬁ guration of group functions

By means of a group function, one transmitter, for

example,

a radio motion detector, controls several receivers.

To do so, the same functions must be conﬁ gured

on all receivers.

Start conﬁ guration (see Conﬁ guring radio mo-

tion detector as transmitter).

Select function on receiver: Select the group

function as described above on each receiver

to be integrated and conﬁ rm function on the

receiver.

Completing the conﬁ guration: Brieﬂ y press the

cfg button on the transmitter.

Setting the switch-on time for the timer

The switch-on time on the receiver can be set in

stages for the function. Timer

The factory setting is 3 min.

Start conﬁ guration.

If necessary, : Select select transmitter button

the button with the timer.

The Select transmitter button step does not

apply for radio motion detectors as transmit-

ters.

Select function on receiver: If the func-Timer

tion is displayed through the LED ﬂ ashing fct

red (Table 5), keep the fct button on the re-

ceiver pressed for longer than 5 seconds, until

the cfg LED ﬂ ashes brieﬂ y.

The ﬂ ashing fct LED shows the currently set

switch-on time - with a factory setting of 5x

(Table 9).

x number of ﬂ ashes of

the fct LED

Switch-on time

1 s

30 s

1 min

2 min

3 min

5 min

15 min

30 min

1 h

3 h

Table 9: Settable switch-on times

Press the button.fct

Each short press of the fct button increases

the switch-on time by one step.

During the setting, the LED indicates the fct

switch-on time (Table 9) for orientation.

Press the button for longer than 2 seconds fct

to apply the desired switch-on time.

Completing the conﬁ guration: Brieﬂ y press the

cfg button on the transmitter.

Resetting the KNX radio motion detector to

factory settings

The device is not in conﬁ guration mode.

Keep the button pressed for longer than 10 cfg

seconds, until the LED switches from being cfg

red to ﬂ ashing.

Release the button.cfg

The cfg LED ﬂ ashes rapidly in red. The device

re-initialises itself. In the meantime, the cfg

LED turns red. After that, the LED goes out

and ﬂ ashes 5x to indicate the compatibility. The

reset is has been completed. The process lasts

about 20 s.

This process deletes the complete conﬁ gura-

tion of the radio motion detector. Settings of the

insert (switch-on brightness level, load setting)

are not reset.

Operation

Result

Start conﬁ guration



Brieﬂ y press the cfg button on the radio motion

detector on the power supply (transmitter, slave).

150

90°

...

45° 45°

...

90°

fct

If there is no further operation, the conﬁ guration is

automatically ended after 10 minutes.

The LEDs on the radio motion detector cfg

(slave and master) light up in red colour.

150

90°

...

45° 45°

...

90°

fct

cfg

150

90°

...

45° 45°

...

90°

fct

cfg

All the receivers within radio range also display

the conﬁ guration mode.

Select function on receiver



Brieﬂ y press the cfg button on the radio motion

detector on the switch insert or ﬂ ush-mounted

dimmer (master) to select the master-slave

function.

150

90°

...

45° 90°

fct

cfg

Only the master-slave function or delete can be

selected in this conﬁ guration.

The fct LED ﬂ ashes orange periodically

(see Table 5).

150

90° 45° 45° 90° ... ...

fct

cfg

Conﬁ rm function on receiver



To save the allocation of command and function,

keep the fct button on the receiver (master)

pressed for more than 2 seconds.

150

90° 45° 90° ...

fct

cfg

> 2 s

The cfg LED ﬂ ashes. After successful saving,

the LED signals the saved function. fct

Rapid ﬂ ashing of the cfg LED indicates an

error.

Completing the conﬁ guration



Brieﬂ y press the cfg button on the transmitter

(slave).

150

90°

...

45° 45°

...

90°

fct

The LEDs on the radio motion detectors and cfg

all receivers within radio range go out. The mas-

ter-slave conﬁ guration has been executed.

Table 8: Executing the master-slave conﬁ guration

Operation

Result

Start conﬁ guration



Brieﬂ y press the cfg button on the radio

motion detector.

150

90°

...

45° 45°

...

90°

fct

If there is no further operation, the

conﬁ guration is automatically ended after 10

minutes.

The LEDs on the radio motion detector and the cfg

receivers within radio range light up in red colour.

Radio motion detector (transmitter) and receiver are

in conﬁ guration mode.

150

90°

...

45° 45°

...

90°

fct

cfg

cfg fc t

off

5 7 8321 4 6

L N S1

fct

cfg

Select function on receiver



Brieﬂ y press the fct button several times on

the receiver to select the desired function

(see the receiver operating instructions).

cfg fct

off

5 7 8321 4 6

L N S1

fct

cfg

After each actuation, the fct LED displays a function.

If the radio motion detector has already been

conﬁ gured with a function in a diﬀ erent receiver

and/or the conﬁ gured function is part of a group

control, only this function can be conﬁ gured.

To change a function, the existing conﬁ guration

needs to be deleted and the new one conﬁ gured.

Conﬁ rm function on receiver



To save the allocation of command and

function, press the fct button on the receiver

for longer than 2 seconds.

The cfg LED ﬂ ashes. After a successful saving, the

fct LED signals the saved function.

Rapid ﬂ ashing of the cfg LED indicates a

combination that is not possible or an error.

Completing the conﬁ guration



Brieﬂ y press the cfg button on the radio

motion detector.

150

90°

...

45° 45°

...

90°

fct

The LEDs on the radio motion detector and all re-cfg

ceivers within radio range go out. The radio command

for the radio motion detector has been conﬁ gured.

Table 7: Conﬁ guration of KNX radio motion detector as a transmitter

Specyfikacje produktu

Marka:	Hager
Kategoria:	nieskategoryzowany
Model:	85345126
Kolor produktu:	Czarny
Długość kabla:	1.8 m
Szerokość opakowania:	177.8 mm
Wysokość opakowania:	12.7 mm
Głębokość opakowania:	228.6 mm
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Ilość na paczkę:	1 szt.
Kraj pochodzenia:	Tajwan
Zakres temperatur (eksploatacja):	-5 - 45 °C
Zakres wilgotności względnej:	0 - 65 %
Kod zharmonizowanego systemu (HS):	84733080
Waga wraz z opakowaniem:	140 g
Wysokość skrzyni wzorcowej (zewnętrznej):	25.4 mm
Długość skrzyni głównej (zewnętrznej):	457.2 mm
Waga brutto obudowy głównej (zewnętrznej):	1130 g
Szerokość skrzyni zbiorczej (zewnętrznej):	406.4 mm
Maks. rozdzielczość:	1920 x 1200 px
W opakowaniu zbiorczym GTIN (EAN / UPC):	10037332201116
Liczba dołączonych produktów:	1 szt.
Obsługa funkcji Plug & Play:	Tak
Produkty w skrzyni głównej (zewnętrznej):	10 szt.
Materiał pokrycia styków:	Złoto
Złączka 2:	HD15, MICRO-USB B
Złączka 1:	HDMI
Złącze 1:	Męska
Złącze 2:	Żeńska
Maksymalna rozdzielczość (HDMI):	1920 x 1200 px