Instrukcja obsługi Hager 6380142109

Hager nieskategoryzowany 6380142109

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hager 6380142109 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Berker GmbH & Co. KG - Klagebach 38 - 58579 Schalksmühle/Germany - Telefon: + 49 (0) 23 55/90 5-0 - Telefax: + 49 (0) 23 55/90 5-111 - www.berker.com -
Operating and
assembly instructions
8014 11 x0
KNX push button module
1gang
8014 21 x0
KNX push button module
2gang
z
6LE000414A - 06/2015
6LE000414A
Safety instructions z
Electrical equipment may only be installed and
assembled by a qualifi ed electrician. Always fol-
low the relevant accident prevention regulations
of the country.
Failure to comply with these installation instruc-
tions may result in damage to the device, fi re or
other hazards.
When installing and laying cables, always comply
with the applicable regulations and standards for
SELV electrical circuits.
During renovation work, protect the device from
pollution by paint, wallpaper paste, dust etc. The
device can be damaged.
These instructions are an integral component of
the product and must be retained by the end us-
er.
Design and layout of the device
Figure 1: Design and layout of the device
(1) Touch cover (not within scope of delivery)
(2) Push-button module
(3) Fastening clamps
(4) Frame (not within scope of delivery)
(5) Supporting ring with prong connection
(6) Screw for dismantling protection
(7) Status LEDs
Function
System information
This device is a product of KNX system and corre-
sponds to the KNX guidelines. Detailed specialised
knowledge obtained from KNX training courses is
required for comprehension. The planning, installa-
tion and commissioning are carried out with the help
of KNX-certifi ed software.
system link start-up
The function of the device is software-dependent. The
software is to be taken from the product database. You
can fi nd the latest version of the product database,
technical descriptions as well as conversion and addi-
tional support programmes on our website.
easy link start-up
The function of the device is confi guration-de-
pendent. The confi guration can also be done using
devices developed specially for simple setting and
start-up.
This type of confi guration is only possible with devic-
es of the easy link system. easy link stands for easy,
visually supported start-up. Preconfi gured standard
functions are assigned to the in/outputs by means of
a service module.
Correct use
- Operation of consumers, e.g. light on/off, dim-
ming, blind up/down, saving and opening light
scenes, etc.
- Installation into wall box according to DIN 49073
Product characteristics
- Start-up and programming in S-mode and E-mode
- Push-button functions: switching/dimming, blind
control, value transmitter, scene call-up, specifi ca-
tion of the heating operating mode, forced control,
stepping switch and comparator function
- One status LED per rocker
- Function and colour of the status LEDs confi gur-
able for the device
- Integrated bus application unit
Operation
Triggering of functions and operation of electrical
loads takes place via touch surfaces (fi gure 2,
dashed) and can be set individually for each device.
There are two operating modes:
- Single-surface operation:
Switching lighting on/off and dimming brighter/
darker is carried out alternately by repeated
touching of a touch surface.
- Two-surface operation:
Two superimposed touch surfaces form a function
pair. For example, touching the top surface switch-
es/dims lighting on/makes it brighter, touching the
bottom surface switches it off/makes it darker.
Operating a function or load
Consumers, such as lighting, blinds, etc., are operat-
ed using the touch surfaces, which are dependent on
the device confi guration.
Touch a touch surface.
The stored function is executed.
The actuation pulse lasts for the duration of the
actuation. Depending on the function, short and
long touches can trigger different actions, e.g.
switching/dimming.
(1)
(2) (3)
(4)
(5)
(6)
(7)
1
2
Berker GmbH & Co. KG - Klagebach 38 - 58579 Schalksmühle/Germany - Telefon: + 49 (0) 23 55/90 5-0 - Telefax: + 49 (0) 23 55/90 5-111 - www.berker.com - 6LE000414A - 06/2015
Information for electricians z
Installation and electrical connection
DANGER!
Touching live parts in the installation
environment can result in an electric
shock.
An electric shock can be lethal!
Disconnect the connecting cables
before working on the device and cover
all live parts in the area!
ç
Connecting and installing the device
Mount the supporting ring (5) to a wall box in the
correct position. Note marking TOP/OBEN.
Run the bus cable with the connecting terminal
through the frame and connect it to the push-but-
ton module (2) at the back.
Attach the push-button module (3) with the frame
(5) to the supporting ring until the fastening brack-
ets (4) engage.
Fix dismantling protection with screw (6) if desired.
Reattach touch cover (1) to push-button module
(2).
Dismantling
Remove touch cover (1) from push-button module.
Loosen screw for dismantling protection (6).
Remove push-button module (2) from supporting
ring. Hold on to design frame.
Start-up
The device is connected and ready for operation. In
general the following procedure is recommended.
system link - Loading the physical address and
application software (Figure 3)
(8) Programming button
(9) Programming LED
The physical address is only ever assigned for
one device. Only one device can ever be in pro-
gramming mode.
It is advisable to program the physical address
before installation.
If available, release the touch cover using the
programming button (8).
Switch on bus voltage.
Press programming button (8).
The programming LED (9) lights up.
If the programming LED does not light up, no bus
voltage is present.
Load the physical address into the device.
The programming LED goes out.
Load application software. Note down the physical
address on the labelling fi eld.
The loading of non-compatible application soft-
ware is indicated by fl ashing of the status LEDs
(7).
Reattach the touch cover.
easy link
Information on the system confi guration can be taken
from the extensive description of the service module
easy link.
Appendix
Technical data
KNX Medium TP 1
Start-up mode system link, easy link
Rated voltage KNX DC 21 … 32 V SELV
Current consumption KNX typ. 10 mA
Connection mode KNX bus connecting terminals
Dimensions (W x H x D) 71 x 71 x 32 mm
assembling height from supporting ring 11 mm
Degree of protection IP 20
Protection class III
Operating temperature -5 … +45 °C
Storage/transport temperature -20 … +70 °C
Standards EN 60669-2-1; EN 60669-1
EN 50428
Troubleshooting
Bus operation is not possible.
Cause: Bus voltage is not present.
Check bus connection terminals for correct
polarity.
Check bus voltage by briefl y pressing the pro-
gramming button (8), red programming LED (9)
lights up if bus voltage is present.
Accessories
Cover 1gang with lens 8096 02 xx
Cover 2gang with lens 8096 03 xx
Warranty
We reserve the right to make technical and formal
changes to the product in the interest of technical
progress.
Our products are under guarantee within the scope of
the statutory provisions.
If you have a warranty claim, please contact the point of
sale or ship the device postage free with a description of
the fault to the appropriate regional representative.
(8)(9)
3

Specyfikacje produktu

Marka: Hager
Kategoria: nieskategoryzowany
Model: 6380142109

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hager 6380142109, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Hager

Hager

Hager VS418PZF Instrukcja

15 Sierpnia 2024
Hager

Hager VS318PZF Instrukcja

15 Sierpnia 2024
Hager

Hager VS218PZF Instrukcja

15 Sierpnia 2024
Hager

Hager TN204S Instrukcja

15 Sierpnia 2024
Hager

Hager TN206S Instrukcja

15 Sierpnia 2024
Hager

Hager EH171A Instrukcja

15 Sierpnia 2024
Hager

Hager EG203 Instrukcja

14 Sierpnia 2024
Hager

Hager EG403E Instrukcja

14 Sierpnia 2024
Hager

Hager M-RG404020 Instrukcja

14 Sierpnia 2024
Hager

Hager 80262160 Instrukcja

14 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024