Instrukcja obsługi Genelec AIW26B

Genelec głośnik AIW26B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Genelec AIW26B (8 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
Operating Manual
AIW26B
Genelec AIW26B Operating Manual
Figure 1. Symmetrical L-C-R
loudspeaker placement
Introduction
The Genelec AIW26B Active In-wall
loudspeaker system consists of a bass
reflex type two-way loudspeaker and a
matched remote amplier module, RAM1.
It The AIW26B can be used in the most
demanding applications, like the main
L-C-R array of a Home Theater system,
critical Stereo listening or rear/side
channels of a large, state-of-the-art Home
Theater.
Unpacking
A Genelec AIW26B set includes the items
listed below. Check that nothing is missing
or damaged during transport and delivery. If
there is a problem with the product, contact
your local Genelec dealer.
• AIW26B loudspeaker unit.
• Grille
•
AIW26B cardboard cut-out template
• RAM1 amplier unit
• Mains power cable
•
Plexiglass cover for the control
switches
• This Operating Manual
Installation
Genelec recommends that you use the
services of an authorized installation
speci alist or oth e r co m petent and
experienced installation company for the
installation of the AIW26B system. Ask your
local Genelec dealer for recommended
installation companies in your region.
Matching loudspeakers
and amplifiers
Each AIW26B loudspeaker unit has been
factory calibrated for optimum performance
with the RAM1 amplifier it is shipped
with. Never mix these matched amplifier-
loudspeaker systems in the installation
process. The matching units are marked with
the same ID number on the reex port of the
AIW26B enclosure and the top panel of the
RAM1
.
Loudspeaker placement
Genelec AIW26B loudspeakers are
equipped with Genelec’s proprietary
Directivity Control Waveguide (DCW). One
of the main characteristics of the DCW
technology is that the loudspeakers give
a very even and consistent frequency
response over a larger listening area than
conventional loudspeakers. A secondary
function of the DCW is to reduce the o-axis
radiated sound energy, thereby minimizing
the reections from the side walls, oor and
ceiling. This results in a precise and stable
sound image
If the AIW26B loudspeakers are used in an
application where their capability for precise
sound imaging is needed, such as the front
channels of a Surround Sound system or
a Stereo system, we recommend that the
loudspeakers are placed as far as possible
from wall corners and other reflective
surfaces. The loudspeakers should be placed
symmetrically in relation to the listening
position and there should be no obstructions
between the loudspeaker and the listener.
This guarantees clear dialogue in lms and
a good stereo image with music. Figure 1
shows a Left-Center-Right arrangement that
works well both as Surround Sound front
channels and a Stereo pair.
Whole house audio installations might
require less stringent placement options. In
these cases be sure to consult this manual
for dip switch settings near boundary
conditions in Table 3.
Side and rear channel speaker placement
in home theaters should follow the practical
guidelines given in 5.1, 7.1 and 3D audio
congurations.
Painting the loudspeakers
The metal mesh grille can be spray painted
to match the wall colour. Do not paint
the loudspeaker enclosure itself, or try
to paint the grille while it is attached to
the loudspeaker. Remove the thin cloth
attached to the grille to avoid clogging
the grille with paint. Paint the grille with a
thin spray. Do not use brushes or rollers.
Be very careful not to clog the holes on the
mesh with paint.
Figure 3. Connect the loudspeaker cable.
Figure 2. Lift the AIW26B enclosure into the
hole.
Installing the AIW26B
loudspeaker enclosure
AIW26B specic pre-construction brackets
are available at your Genelec dealer. In
the following we describe the installation
procedure into an existing wall.
Use the cardboard wall cut-out template
to find the location for the AIW26B. The
template also shows the position of the
loudspeaker drivers, so you can easily
nd the placement that brings them to the
optimum position as outlined in chapter
“Loudspeaker placement”.
Examine the wall structure carefully to
nd a clearly unobstructed location for the
loudspeaker. The loudspeaker enclosure
requires a minimum of 102 millimeters (4
in) of free depth measured from the surface
of the drywall. Note that the grille is slightly
wider and taller than the hole and requires
about 30 millimeters (1 1/16 in) of smooth
wall surface around all sides of the hole.
When you have found a good location,
check that the template is level and trace
the hole onto the wall with a pencil along
the outline of the template. If you are not
sure that the chosen part of wall is free from
obstructions, you can start by making a
smaller hole at the center of the marked area
through which you can probe the inside of
the wall. Use a drywall saw and make the
rst cut at a 45° angle toward the center of
the hole so you can put the cut piece back
in if the location is unsuitable. If you nd no
obstructions, you can make the final cut
along the marked lines.
If you have already connected the RAM1
amplifier units to the system, select the
loudspeaker that has the same ID number
as the amplier it will be driven by.
Lift the loudspeaker into the hole lower
end rst and connect the loudspeaker cable
connectors!
Push the AIW26B loudspeaker into the
hole and turn the four Torx T25 screws
clockwise so that the mounting tabs rotate
outwards. Continue tightening the screws to
to 1.5 Nm (1.1 ft lb) and the drywall is rmly
clamped between the mounting tabs and the
enclosure ange. If necessary, a secondary
support line can be attached to the tab on
the top side of the enclosure.
Next place the grille on the enclosure. The
grille is held in place by magnets.
Figure 4. Loudspeaker cable in place. Figure 5. Tighten the four Torx T25 screws
to 1.5 Nm (1.1 lb ft).

Specyfikacje produktu

Marka: Genelec
Kategoria: głośnik
Model: AIW26B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Genelec AIW26B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Genelec

Genelec

Genelec 3440A Instrukcja

7 Października 2024
Genelec

Genelec 8010 APM Instrukcja

30 Września 2024
Genelec

Genelec 8020D Instrukcja

27 Września 2024
Genelec

Genelec 8340APM Instrukcja

21 Września 2024
Genelec

Genelec 1234A Instrukcja

21 Września 2024
Genelec

Genelec 8430APM Instrukcja

19 Września 2024
Genelec

Genelec 4436A Instrukcja

13 Września 2024
Genelec

Genelec 8010 AW Instrukcja

10 Września 2024
Genelec

Genelec 8040A Instrukcja

9 Września 2024
Genelec

Genelec 8020B Instrukcja

9 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025
Hifonics

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025
Pyle

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025
ION

ION Insta Sound Instrukcja

15 Stycznia 2025
Pure Acoustics

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025
Yamaha

Yamaha WX-010 Instrukcja

15 Stycznia 2025
Polk

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025
Sennheiser

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025