Instrukcja obsługi Genelec 8030B

Genelec głośnik 8030B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Genelec 8030B (32 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/32
8030B
Operating Manual 2-7
Betriebsanleitung 8-13
Manuel d’utilisation 14-19
Käyttöohje 20-25
Bruksanvisning 26-31
2 English
General description
The bi-amplified GENELEC 8030B is a two way
active monitoring loudspeaker designed to be small
but still have high output, low coloration, and broad
bandwidth.
The 8030B is ideal for near field monitoring,
mobile vans, broadcast and TV control rooms, sur-
round sound systems, home studios, multimedia
applications and also for use with computer sound-
cards. As an active loudspeaker, it contains driv-
ers, power amplifiers, active crossover filters and
protection circuitry. The MDE™ (Minimum Diffrac-
tion Enclosure™) loudspeaker enclosure is made
of die-cast aluminium and shaped to reduce edge
diffraction. Combined with the advanced Direc-
tivity Control WaveguideTM (DCWTM), this design
provides excellent frequency balance in difficult
acoustic environments. If necessary, the bass
response of the 8030B’s can be extended with a
suitable Genelec subwoofer.
Positioning the loudspeaker
Each 8030B monitor is supplied with an inte-
grated amplifier unit, mains cable and an operating
manual. After unpacking, place the loudspeaker in
its required listening position, taking note of the line
of the acoustic axis. The axes of all loudspeakers
should converge at ear height at the listening position
(see Figure 1).
Connections
Before connecting up, ensure that the mains
switch is off and the volume control fully counter-
clockwise. These controls are located on the front
panel of the loudspeaker. Do not connect the loud-
speaker to an unearthed mains supply or using an
unearthed mains cable.
Audio input is via a 10 kOhm balanced female
XLR connector labelled “INPUT”. An unbalanced
source may be used as long as pin 3 is grounded
to pin 1 at the unbalanced source connector (see
Figure 2).
The male XLR “OUTPUT” connector can be
used for daisy-chaining up to six 8030B’s together
or for connecting a Genelec 7050B subwoofer. The
volume control attenuates the signal on this output,
so the first “master” loudspeaker on a daisy-chain
can be used to adjust the level on the whole chain.
The volume controls on the “slave” loudspeakers
should be set fully clockwise.
Once the connections have been made, the
loudspeakers are ready to be switched on.
ISSTM autostart function
When the power switch on the front panel of the
loudspeaker is set to “ON”, the Intelligent Signal
SensingTM
(ISSTM) autostart function of the 8030B is
active. Automatic powering down to standby mode
happens after a certain time when playback has
ended. The power consumption in standby mode is
typically less than 0.5 watts. The playback will auto-
matically resume once an input signal is detected
from the source.
There is a slight delay in the automatic power-
ing up. If this is undesirable, the ISS
TM function can
be disabled by setting the “ISS DISABLE” switch
8030B
Active Monitoring System
English 3
on the back panel to “ON” position. In this mode,
the monitor is powered on and off using the power
switch on the front panel.
Setting the volume control
The input sensitivity of the loudspeaker can be
matched to the output of the audio signal source
by adjusting the volume control on the front panel.
Setting the tone controls
The frequency response of Genelec 8030B can
be adjusted to match the acoustic environment by
setting the tone control switches on the rear panel.
The controls are “Treble Tilt”, “Bass Tilt” and “Bass
Roll-Off”. An acoustic measuring system such as
WinMLS is recommended for analyzing the effects
of the adjustments, however, careful listening with
suitable test recordings can also lead to good
results if a test system is not available. Table 1
shows some typical settings in various situations.
Figure 4 shows the effect of the controls on the
anechoic response.
Treble Tilt
Treble Tilt (switch 2) attenuates the treble response
above 5 kHz by 2 dB, which can be used for smooth-
ening down an excessively bright sounding system.
Bass Tilt
Bass Tilt offers three attenuation levels for the bass
response below 1 kHz, usually necessary when the
loudspeakers are placed near room boundaries.
The attenuation levels are -2 dB (switch 4 “ON”), -4
dB (switch 5 “ON”) and -6 dB (both switches “ON”).
Figure 1: Location of the acoustic
axis
Figure 2: Type of cable needed if
unbalanced source is used (ex-
ample shown is RCA output to the
XLR input)
Figure 3: Control and connector layout on the rear panel of
the 8030B.
190 mm
ACOUSTIC
AXIS
> 0,7 m
REFLEX PORT
TONE CONTROLS
Iso-Pod™ TABLE
STAND
THREADS FOR
CEILING AND
WALL MOUNTS
292-8030W
COMPOSANT 'INT ÉRIEURREMPLAÇABL ARÀ L EP
OUVRIR. NE S EXPOSER 'EAU AUCUNPA À L OU L'HUMIDITÉ.
L'UTILISAT EUR.ADRESSER UTERÉPARA NTO TION À U
PERSONNELQUALIFIÉ. CETA PPAREILDOIT ÊTRE
RACCORDÉÀ LAT ERRE.
NOTSUBJECT TER MOISTURE.NO USERSERVICEABLETO WA OR
PARTS I DPNSIDE.REFER SERVICING QUALIFIETO ERSONNEL.
USE EART HED ONNECTIOMAINS C NONLY.
ELECTRIC SHOCKHAZ AR D. DONO PEN.DOT O
WARNING:
RISQUE DECHO LECTRIQUE.NE SC É PA
AVERTIS SEMENT:
LAITE ONLIITET T ÄVÄ S UOJAMAADOITUSKOSKETTIMILLAVARUS-
TET T UUNPIST ORASIAAN.APPARATET MÅ T ILKOPLES JORDET
ST IKKONT AKT APPARATENSKALLANSLUTASTILL JORDA. T UTTAG.
292-80 30T-6
MAINS INPUT
50 / 60 Hz 80 W 230 V~
SERIAL NUMB ER
8030B BI-AMPLIFIED
MONITORING SYST EM
MAGNETICAL SHIELDEDLY
MAD E IN FINLAND www.genele c.com
3
GND +-
OUT
1 2
3
+ GND-
2IN 1
ALL OFF
55 1k 5k 20k
BAS S ANDTREB LE TILT
-2
-4
-6
0
dB
4
5
4+5
BAS S ROLL-OFF
ALL OFF
55 85 500 H z
TREBLE TILT-2dB
BASS ROLL-OFF -6dB 85H z
2
dB
0
-6 3
BASS TILT-2 dB
BASS TILT-6 dB
OFF
BASS TILT-4 dB
ON
ISS DISABLE
CONNECTOR PANEL
(HORIZONTAL)

Specyfikacje produktu

Marka: Genelec
Kategoria: głośnik
Model: 8030B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Genelec 8030B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Genelec

Genelec

Genelec 3440A Instrukcja

7 Października 2024
Genelec

Genelec 8010 APM Instrukcja

30 Września 2024
Genelec

Genelec 8020D Instrukcja

27 Września 2024
Genelec

Genelec 8340APM Instrukcja

21 Września 2024
Genelec

Genelec 1234A Instrukcja

21 Września 2024
Genelec

Genelec 8430APM Instrukcja

19 Września 2024
Genelec

Genelec 4436A Instrukcja

13 Września 2024
Genelec

Genelec 8010 AW Instrukcja

10 Września 2024
Genelec

Genelec 8040A Instrukcja

9 Września 2024
Genelec

Genelec 8020B Instrukcja

9 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025
Hifonics

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025
Pyle

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025
ION

ION Insta Sound Instrukcja

15 Stycznia 2025
Pure Acoustics

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025
Yamaha

Yamaha WX-010 Instrukcja

15 Stycznia 2025
Polk

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025
Sennheiser

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025