Instrukcja obsługi Genelec 4435A

Genelec głośnik 4435A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Genelec 4435A (12 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
Genelec 4435A
Smart IP In-Ceiling Installation Speaker
Operating Manual
4435A
Genelec 4435 Smart IP In-Ceiling Installation Speaker
Introduction
The bi-amplied Genelec 4435A Smart IP
In-Ceiling loudspeaker is a high performance
in-ceiling loudspeaker for xed installations.
It requires only one CAT cable to connect,
making installation easy. The 4435A
is powered using the standard Power-
over-Ethernet (PoE) technology, using
PoE+ or PoE standards. The proprietary
internal power supply in 4435A delivers an
impressive short-term SPL.
The 4435A supports Genelec Smart
IP technology, and it may be used solely,
or together with other Genelec 44xx
models. The Smart IP technology provides
scalable power, audio and loudspeaker
configuration, supervision and calibration
features via a standard CAT cable, oering
integrators unrivalled power, exibility, cost-
eectiveness and simplicity of installation.
The 4435A has been designed for
excellent sound quality and very long
lifetime and manufactured using certified
sustainable methods. All essential parts of
the loudspeaker can be recycled.
The 4435A is available in with four dierent
grille options: white or black round grille and
white or black square grille.
The 4435A loudspeaker contains
• Highly ecient dedicated Class D power
ampliers, one for each driver
• Switched-mode power supply technology
oering high SPL output using standard
PoE+ and PoE power supply with an IP
switch or power injector
• Active crossover lter
• Electronic system protection
• Audio-over-IP streaming input
• Balanced analogue line input
• Flexible room acoustic compensation tool
set built in
The 4435A is designed for indoor use,
in temperatures 15-35 Celsius and non-
condencing humidity
Unpacking
A Genelec 4435A set includes the following
items. Check that nothing is missing or
damaged in transit. If there is a problem
with the product, contact your local Genelec
dealer.
• 4435A loudspeaker
• 4435A cardboard cut-out template
• Euroblock connector for analogue audio
• Square or round grille in black or white
according to order
Installation
If you are installing the 4435A to an existing
construction, examine the ceiling thoroughly
for the shortest and least obstructed
cable route. Be careful to avoid cutting or
drilling into electrical wires, ventilation or
water pipes. All of this is of course much
easier when the installation takes place in
an unfinished building where the ceiling
structure is still open. For new construction
installs, we recommend planning the
loudspeaker placement at an early stage
and using the optional Genelec New
Construction Brackets (order code 272-
0039) for marking the desired locations. The
brackets can be nailed or screwed to the
studs to show the ceiling panel installers the
places where holes for the loudspeakers are
to be located.
When installing the enclosure in an
existing ceiling, use the cardboard ceiling
cut-out template to nd the best location.
The template also shows the position of the
loudspeaker drivers and acoustic axis, so
you can easily nd the placement that brings
them to the desired position
Examine the ceiling structure carefully to
nd a clearly unobstructed location for the
loudspeaker. The loudspeaker enclosure
requires a minimum of 162 millimeters (6
3/8
in) of free depth measured from the outer
surface of the sheetrock. Also note that
the enclosure ange is wider than the hole
and requires about 20 millimeters (3/4 in)
of smooth ceiling surface around the hole
.
When you have found a good location,
check that the template is level and trace the
hole onto the ceiling with a pencil along the
outline of the template. If you are not sure
that the chosen part of ceiling is free from
obstructions, you can start by making a
smaller hole at the center of the marked area
Figure 1. Front and rear views of the 4435A
through which you can probe the inside of
the ceiling. Use a drywall saw and make the
rst cut at a 45° angle toward the center of
the hole so you can put the cut piece back
in if the location is unsuitable. If you find
no obstructions, you can make the nal cut
along the marked lines.
Loosen the screws on the three mounting
latches on the 4435A enclosure a few turns
to allow the latches to turn (see Fig.3).
Connect the cables (see chapter "Cabling")
and a safety wire if one is used.
Lift the 4435A enclosure into the hole
and turn the screws clockwise so that
the mounting latches rotate outwards.
Figure 3. Screws for tightening the
mounting latches are located at the
edge of the front bae
STATUS
INDICATOR
LED
RESET
BUTTON
HOLE
ETHERNET
CONNECTOR
BALANCED
ANALOGUE
CONNECTOR
SAFETY
WIRE
TAB
CABLE STRAIN
RELIEFS
Continue tightening the screws until the
sheetrock is firmly clamped between the
mounting latches and the enclosure ange.
If necessary, a secondary safety wire can be
attached to a tab on the top of the enclosure.
Cabling
To get started, connect an Ethernet cable
from the PoE+ output in an IP switch to
the 4435A Ethernet port. Use at least CAT5
cable or better. The loudspeaker powers up
automatically. If the balanced audio input
is used, connect it before powering up the
speaker. The pin sequence is shown in
Figure 9. When the balanced line input is
used the loudspeaker must still receive PoE
power on the Ethernet cable.
To create a working system, you will need
the following:
• An IP switch with a PoE+ (802.3at) output
for the 4435A loudspeaker or an IP switch
with no PoE support and a PoE+ power
injector
• CAT 5 or higher category Ethernet cable
with RJ45 connectors
• AES67 or Dante audio-over-IP stream
source
• For 4435A setup and configuration,
Figure 2. Connector panel of the 4435A

Specyfikacje produktu

Marka: Genelec
Kategoria: głośnik
Model: 4435A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Genelec 4435A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Genelec

Genelec

Genelec 3440A Instrukcja

7 Października 2024
Genelec

Genelec 8010 APM Instrukcja

30 Września 2024
Genelec

Genelec 8020D Instrukcja

27 Września 2024
Genelec

Genelec 8340APM Instrukcja

21 Września 2024
Genelec

Genelec 1234A Instrukcja

21 Września 2024
Genelec

Genelec 8430APM Instrukcja

19 Września 2024
Genelec

Genelec 4436A Instrukcja

13 Września 2024
Genelec

Genelec 8010 AW Instrukcja

10 Września 2024
Genelec

Genelec 8040A Instrukcja

9 Września 2024
Genelec

Genelec 8020B Instrukcja

9 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025
Hifonics

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025
Pyle

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025
ION

ION Insta Sound Instrukcja

15 Stycznia 2025
Pure Acoustics

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025
Yamaha

Yamaha WX-010 Instrukcja

15 Stycznia 2025
Polk

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025
Sennheiser

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025