Instrukcja obsługi GE ZDIS150ZSS

GE Maszyna do lodu ZDIS150ZSS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE ZDIS150ZSS (18 stron) w kategorii Maszyna do lodu. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/18
Installation
Instructions
Automatic Ice maker
ZDIC150
ZDIS150
Design Guide
With Installation Instructions
monogram.com
Installation Instructions
 BEFORE YOU BEGIN:
Read these instructions completely and carefully.
 IMPORTANT:
Save these instructions for local inspector’s use.
 IMPORTANT:
Observe all governing codes and ordinances.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded.
Failure to do so can result in death, fire or electrical
shock. See Power Supply,” page 6.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Le non-respect de ces instructions peut causer la
mort, un incendie ou un choc électrique. Consulter «
Alimentation électrique », page 6.
If you received a damaged ice maker, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
8VHWKLVDSSOLDQFHRQO\IRULWVLQWHQGHGSXUSRVH
Check with local utilities for electrical codes that
apply in your area. Local codes vary. Installation,
electrical connections and grounding must comply
with applicable codes. In the absence of local codes,
the ice maker should be installed in accordance
with National Electrical Code ANSI/NFPA 70-1990 or
latest edition.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
2
CONTENTS
Design Information
Models Available .................................................................... 3
Optional Accessories ........................................................... 3
Tools and Materials Required ........................................ 3
Cutout & Product Dimensions .........................................4
Installation
Advance Planning .................................................................4
Water Supply ........................................................................... 5
Power Supply ...........................................................................6
Remove Packaging ............................................................... 6
Water Filtration System .................................................6, 7
Adjust Height of Ice maker ...............................................7
Connect the Drain .................................................................9
Connect Water Supply to Appliance ............................9
Reverse Door Swing ...................................................10, 11
Accessories
ZPK2 Auxiliary Pump Kit ............................................12-15
ZIP75BB Kit for 3/4” thick panels ..........................16, 17
Design Information
MODELS AVAILABLE
ZDIC150ZBB, ZDIS150ZSS
Available in black and stainless steel.
The ice maker may be installed below a countertop
or used free-standing.
3
OPTIONAL ACCESSORIES
=,3%For the installation of a trimless
3/4thick custom panel on black models (not for
stainless steel models). This kit provides a handle
that can be installed with the custom panel.
A custom handle of your choice may be installed onto
the 3/4” panel. See installation instructions
on pages 10 and 11.
ZPK2 Drain Pump Kit - For use when a floor drain is
not available. The drain pump must be installed
inside the unit and can pump discharge water at a
maximum vertical height of 10 feet. 10 feet of tubing
is supplied with the kit.
TOOLS AND MATERIALS REQUIRED FOR BASIC INSTALLATION
µVRFNHW
µDGMXVWDEOHZUHQFK
/HYHO
*(6PDUW&RQQHFW Refrigerator Tubing Kit or 1/4” O.D.
copper tubing, of sufficient length to reach the installation
)ODWEODGHVFUHZGULYHU
µDQGµRSHQHQGZUHQFKHVRUDGMXVWDEOHZUHQFKHV
µQXWGULYHU


Specyfikacje produktu

Marka: GE
Kategoria: Maszyna do lodu
Model: ZDIS150ZSS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE ZDIS150ZSS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Maszyna do lodu GE

Instrukcje Maszyna do lodu

Najnowsze instrukcje dla Maszyna do lodu

Royal Catering

Royal Catering RCSL 2/12 Instrukcja

15 Października 2024
Royal Catering

Royal Catering RC-ICM24 Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCSL 3/12 Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCSI-16A Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCSL 3/15 Instrukcja

14 Października 2024
Marvel

Marvel MRNP215-IS01A Instrukcja

9 Października 2024
Marvel

Marvel MONP215-SS01A Instrukcja

9 Października 2024
Marvel

Marvel MACR214-SS01B Instrukcja

9 Października 2024
Marvel

Marvel MPCP415-SG81A Instrukcja

9 Października 2024