Instrukcja obsługi GE UPK4

GE lodówka UPK4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE UPK4 (12 stron) w kategorii lodówka. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com
Installation Drain Pump
Instructions Kit UPK4
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT – Save these
instructions for local inspector’s use.
• IMPORTANT – Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Proper installation is the responsibility of installer.
• Product failure due to improper installation is not
covered under the Warranty.
WHAT YOU WILL NEED:
3/8” open/box wrench or adjustable wrench
Drill with phillips head bit or #2 Phillips screwdriver
Slip joint pliers
Side cutting pliers
31-1000617 Rev. 2 09-22 GEA
1
3
2
4
5
7
8
9
6
KIT CONTENTS:
1 - Drain Pump & Check Valve Assembly (1)
2 - PVC Drain Pipe & Pressure Sensor
Assembly (1)
3 - Rubber Pad (For Pump Mounting) (1)
4 - Discharge Tubing - Clear (1)
5 - Metal Clamp (For Discharge Tubing) (1)
6 - Plastic Snap Ring (1)
7 - Pump Fixing Bolts (2); Spring Washer (2);
Flat Washer (2)
8 - Pressure Sensor Case Screw (ST/4*12) (1)
9 - Ground Screw With Washer (M/4*8) (1);
Lock Washer(1)
NOTE: This pump can be installed in a cube ice machine or
a nugget ice machine.
231-1000617 Rev. 2
Installation Instructions
INSTALLING PUMP KIT (Cont.)
DISCONNECT ELECTRICAL POWER
1 REMOVE ACCESS COVER
Ŷ Use a drill or a Phillips screwdriver to remove the
2 screws from the access panel as shown in figure
below. Slide the panel in the direction shown to
remove.
2 REMOVE DRAIN TUBING
Ŷ Remove the plastic snap ring from the main drain
tube and release the small metal clamp on the
short drain tube which connected outlet valve. Pull
both tube down. Remove the small metal clamp
from the tube. Keep both snap ring and clamp for
pump kit installation
Ŷ Remove the white drain pipe by pulling it down
from the 2 locations shown.
3 INSTALL RUBBER PAD TO NEW
PUMP
Ŷ Remove the rectangular rubber pad from pump
kit and peel off the white sticker. Attach the sticky
side to the drain pump base.
WARNING Electrical Shock Hazard
Death or serious injury can result from failure to
follow these instructions.
• Service by a qualified service technician only.
• Disconnect power before servicing this product.
• Reconnect all grounding devices after service.
• Replace all parts and panels before operating.
Screws
Access
Panel
Slide panel in
this direction
White Sticker
Rubber Pad -
Sticky side up
Snap
Ring
Short
Drain
Tube
Main
Drain
Tube
Outlet
Valve
Small
Metal
Clamp
31-1000617 Rev. 2 3
4 INSTALL NEW DRAIN TUBING
Ŷ Install the new white drain tubing in the
accessories to the drain pump and clamp with the
snap ring included in the kit.
5 INSTALL THE DRAIN PUMP
Ŷ Insert the red connector of the drain pump into the
red connector you will see on a wire inside of the
ice machine.
Ŷ Slide the drain pump into the ice machine so the
base slides under the tab on the base of the ice
machine floor. The front of the pump with the hose
attached will face the front of the ice machine.
5 INSTALL THE DRAIN PUMP
(Cont.)
Ŷ Using the hardware from the kit, attach the pump
to the ice maker floor using a wrench.
6 CONNECT DRAIN PUMP TO ICE
MACHINE
Ŷ Slide the small metal clamp, which you saved
from original tube assembly, on the short drain
tube of the PVC drain pipe as shown in the picture
below. Push the pipe up to connect both tubes
to the fittings from the ice machine which you
disconnected earlier. Snap and secure the snap
ring back on the connection of the main drain tube.
Slide up and secure the small metal clamp up and
tighten at the connection.
Installation Instructions
INSTALLING PUMP KIT (Cont.)
White Drain
Tubing
Snap Ring
Red Connectors
Tab

Specyfikacje produktu

Marka: GE
Kategoria: lodówka
Model: UPK4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE UPK4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje lodówka GE

GE

GE GBR20DSERBS Instrukcja

13 Stycznia 2025
GE

GE Profile Performance TPX24PBDCC Instrukcja

11 Stycznia 2025
GE

GE Profile PCF23RGWBB Instrukcja

15 Grudnia 2024
GE

GE PCG 23NHF WW BL Instrukcja

15 Grudnia 2024
GE

GE Café CXQW1H1PPFB Instrukcja

8 Grudnia 2024
GE

GE Café CXLB3H3PMCU Instrukcja

8 Grudnia 2024
GE

GE Café CXQD2H2PNCU Instrukcja

8 Grudnia 2024
GE

GE Café CXLB3H3PMBT Instrukcja

8 Grudnia 2024
GE

GE Café CXQW1H1PPBZ Instrukcja

8 Grudnia 2024
GE

GE GXRTQR Instrukcja

8 Grudnia 2024

Instrukcje lodówka

Najnowsze instrukcje dla lodówka

Siemens

Siemens KA 58 NP 95 Instrukcja

15 Stycznia 2025
Zanussi

Zanussi ZRB 29 NC8 Instrukcja

15 Stycznia 2025
Fisher & Paykel

Fisher & Paykel RF442BRPUX6 Instrukcja

15 Stycznia 2025
Amica

Amica FDR2213B Instrukcja

15 Stycznia 2025
Siemens

Siemens KG 33 VX 41 Instrukcja

15 Stycznia 2025
Bauknecht

Bauknecht KRIS 1509A Instrukcja

15 Stycznia 2025
Dometic

Dometic RM 7400 L Instrukcja

15 Stycznia 2025
LG

LG GR-B652YVSK Instrukcja

15 Stycznia 2025
Zanussi

Zanussi ZRB34211XV Instrukcja

15 Stycznia 2025
Hotpoint

Hotpoint HTR15ABRLCC Instrukcja

15 Stycznia 2025