Instrukcja obsługi GE Profile PDWT580RSS

GE pralka Profile PDWT580RSS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE Profile PDWT580RSS (32 stron) w kategorii pralka. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/32
GE Consumer & Industrial
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com
In Canada call 1.800.561.3344 or www.GEAppliances.ca
imagination at work
IMPORTANT – The dishwasher MUST
be installed to allow for future removal from the enclosure
if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for available
custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While performing
installations described in this booklet, gloves and either
safety glasses or goggles should be worn.
ANTI
BACTERIA
ST AR T
RESET
TO LOCK CONTRO LS
PRESS HEATED
DRY
FOR 3 S E
CONDS
ENHANCEMENTS
SELECTIONS
SEN SIN
GWAS HIN
GRINS IN
GDRY IN
GSAN IT
IZE DCLEAN
COOK
WARE
NORMAL
WASH
SP EED
CYCLE
CHINA
CRYS TAL
RINSE
ONLY 2 4 8
DELAY
HOURS
ADDED
HEAT
PRE
WASH
HEATED
DRY
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Stainless Steel Tub Models
IMPORTANT – Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these instructions for the
consumer’s and local inspector’s use.
• Note to Consumer – Keep these instructions with your
Owner’s Manual for future reference.
• – Installation of this dishwasher requires Skill Level
basic mechanical, electrical and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.
• . New installations require Completion Time – 1 to 3 Hours
more time than replacement installations.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
STOP
PARTS SUPPLIED WITH
INSTALLATION KIT:
Two #8-18 x 5/8" Phillips special head screws, to
secure dishwasher to underside of countertop or
sides of cabinets.
Junction box cover and #10-1/2" hex-head screw
Side and top trim
Trim Panel Accessory Kit (not shown)
(Custom panel models only)
Sound upgrade kit (some models)
Drain hose (78") , drain hose hanger and hose
clamp
Literature, product samples and/or coupons
Hard water test strip (Models with Bulk Dispenser)
Installation Preparation
TOOLS YOU WILL NEED:
Phillips-head screwdriver
1/4" and 5/16" nutdriver
6" Adjustable wrench
Level
Carpenter’s square
Measuring tape
Safety glasses
Flashlight
Bucket to catch water when flushing the line
15/16" socket
Gloves
For New Installations Only:
Tubing cutter
Drill and appropriate bits
Hole saw set
MATERIALS YOU WILL NEED:
Ferrule, compression nut and 90° Elbow (3/8" NPT
external thread on one end, opposite end sized to
fit water supply)
Thread seal tape
UL-listed wire nuts (3)
Materials For New Installations Only:
Air gap for drain hose, if required
Waste tee for house plumbing, if applicable
Electrical cable or power cord, if applicable
Screw-type hose clamps
Strain relief for electrical connection
Hand shut-off valve
Water line 3/8" min. copper
Coupler for extending drain line, if applicable
GPF10L 10' drain hose, if needed
#8 Phillips
Special Head Screws
5/8” long
Hose Clamp
Drain Hose (78")
Trim Pieces
Hand
Shut-Off
Valve
90° Elbow,
Ferrule and
Compression Nut
Thread
Seal Tape
Wire Nuts (3)
Hot Water Line
Electrical Cable
(or Power Cord, if applicable)
Waste Tee
Coupler
Air
Gap
Screw-Type
Hose Clamps
Strain Relief
Phillips-
Head
Screwdriver
1/4" and
5/16" Nutdriver
Level
Carpenter’s
Square
1/4" and
15/16" Socket
6" Adjustable
Wrench
Tubing Cutter
Measuring Tape
Safety GlassesFlashlight
Gloves Bucket Hole Saw Set Drill and Bits
2
Drain Hose Hanger
#10 Hex-Head
J-Box Screw
1/2" long
Sound Upgrade Kit
(Some Models)
GPF10L
10' Drain Hose
Junction
Box Cover
Screw Kit
Hard Water Test Strip
(Models with
Bulk Dispenser)
Side Trim
Top Trim
Side Trim
3
Installation Preparation–Enclosure
PREPARE DISHWASHER ENCLOSURE
Figure A
To reduce the risk of shock, fire, or injury
to persons, the installer must ensure that
the dishwasher is completely enclosed at
the time of installation.
WARNING
• The rough cabinet opening must have a minimum width
and depth of 24" and height of 34-1/2" ± 1/4" from the fl oor
to the underside of the countertop.
• The back wall should be free of pipes or wires.
• Adjacent cabinets should be square and plumb to ensure
a good fi t. Refer to Figure A
• For a corner installation, allow 2" minimum clearance
between the dishwasher and the adjacent wall.
• Provide at least 28-3/8" in front of the dishwasher to allow
the dishwasher door to open fully. Refer to Figure B
• Make sure the fl oor is level inside the opening and even with
the fi nished fl oor of the kitchen. This will facilitate removal
of the dishwasher at a later date for service, if needed.
Special consideration for a dishwasher installed on
a elevated platform
The elevated platform must be flat and level.
Cabinets
Square
and
Plumb
Floor MUST
be Even with
Room Floor
This Wall Area
Must Be Free of
Pipes or Wires
Plumbing and Electric Service
Must Enter Shaded Area
34-1/2" ± 1/4"
Underside of
Countertop
to Floor
24"
Min.
24" Min.
5" 5"
4" 4"
6"
Figure B
• The dishwasher must be installed no more than 10 feet
from sink for proper drainage.
• The dishwasher must be fully enclosed on the top, sides
and back.
• The dishwasher must not support any part of the enclosure.
2" Minimum
Countertop
Dishwasher
28-3/8" Minimum
Clearances:
In a corner installation, provide at
least 2" clearance between the
dishwasher and the adjacent
cabinet, wall, or other appliance.
Provide at least 28-3/8" of clearance
in front of the dishwasher.
Para reducir el riesgo de choque, incendio
o lesión a personas, el instalador se
debe cerciorar de que la lavadora esté
completamente cerrada en el momento
de la instalación.
ADVERTENCIA

Specyfikacje produktu

Marka: GE
Kategoria: pralka
Model: Profile PDWT580RSS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE Profile PDWT580RSS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje pralka GE

GE

GE GSD3715FAA Instrukcja

15 Października 2024
GE

GE GSD6700GCC Instrukcja

14 Października 2024
GE

GE GLD5706VCC Instrukcja

8 Października 2024
GE

GE GLDL500NCC Instrukcja

7 Października 2024
GE

GE Profile PDWT500PWW Instrukcja

6 Października 2024
GE

GE GSD2200GWW Instrukcja

6 Października 2024
GE

GE GSD3300NWW Instrukcja

6 Października 2024
GE

GE GSD2020ZBB Instrukcja

4 Października 2024
GE

GE GSD2000FAD Instrukcja

4 Października 2024
GE

GE GTW485ASWWB Instrukcja

3 Października 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Candy

Candy CS 15102D3-80 Instrukcja

15 Października 2024
Siemens

Siemens iQ700 WI14W540EU Instrukcja

15 Października 2024
LG

LG WTP22BK Instrukcja

15 Października 2024
Freggia

Freggia WTIE148 Instrukcja

15 Października 2024
Freggia

Freggia WISE126R Instrukcja

15 Października 2024
Freggia

Freggia WISE126B Instrukcja

15 Października 2024
Freggia

Freggia WISE126 Instrukcja

15 Października 2024
Freggia

Freggia WISA105 Instrukcja

15 Października 2024
Freggia

Freggia WISA106 Instrukcja

15 Października 2024
Freggia

Freggia WIA107 Instrukcja

15 Października 2024