Instrukcja obsługi GE Profile PDWT502VII

GE pralka Profile PDWT502VII

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE Profile PDWT502VII (3 stron) w kategorii pralka. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Dimensions and Installation Information (in inches)
For answers to your Monogram,
® Profile™
Series or GE® appliance questions, visit our
website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
Specification Revised 3/13 250244
Listed by
Underwriters
Laboratories
This wall area
must be free of
pipes or wires
Countertop
4
6
Hot
water
line on
left
44
2Plumbing and electrical
service must enter
inside shaded area
24" From wall
24" MIN.
90°
19" MIN. from wall
24"
MIN.
6
34" to 34-3/4"
Underside
of countertop
to floor
5 5
90°
Electrical
wiring on
right
Electrical
wiring is
3" from
cabinet
Electrical Rating
Voltage AC.......................................................... 120
Hertz..................................................................... 60
Total connected load amperage............. 9.9
Calrod® heater watts max........................ 875
For use on adequately wired 120-volt,
15-amp circuit having 2-wire service
with a separate ground wire. This appliance
must be grounded for safe operation.
Installation Information: Before installing,
consult installation instructions packed with
product for current dimensional data.
††† Add 3/4" for custom panel and additional
room for custom handle
An installation template is packed with these
models and may be obtained in advance.
Order Pub. No. 5-X063.
PDWT502VII
GE Profile™ Series Dishwasher with SmartDispense™ Technology
Listed by
Underwriters
Laboratories
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
GE Pub. No. 031-30569-1
Custom Dishwasher Door Panel Template
Top of Panel Top of Panel
Trim Around Dotted Line
11-5/16"
Trim Around Dotted Line
2-9/32"
25-9/16"
11-5/16"
2-9/32"
25-9/16"
Trim Around Dotted LineTrim Around Dotted Line
Drill 3/32"
Pilot Hole
3/32" Deep
Drill 3/32"
Pilot Hole
3/32" Deep
Drill 3/32"
Pilot Hole
3/32" Deep
Drill 3/32"
Pilot Hole
3/32" Deep
3/4" Thick Custom Panel
Template Instructions for
Top Control Integrated Profile and
Monogram Dishwasher Models
T he custo m pa nel should be size d t o your installat ion situatio n. See Step 1. For easier
insta llat ion t he custom pa nel and cust om handle should be attached before installing the
dishwas her. Use t his t emplat e t o locate mount ing screws and spa cers on the custom panel.
IMPO ANTRT
• A cust om handle must be inst alle d ont o t he cust om
panel. Inst all t he cust om handle 4-1/2" max. from
t he t op of t he pan el .
STEP 2 DRAW CENTERLINE
• P lace the custom panel on a flat surface with appearance side
down.
• Locate the vertical center of the panel at the top.
• Use a carpenters square to draw a centerline from top to bottom.
STEP 4 INSTALL MOUNTING SCREWS AND SPACERS
Mark Center
Screw H ol es
STEP 5 INSTALL CUSTOM HANDLE
A custom handle must be installed onto the panel
before the panel is secured to the dishwasher door.
• T he handle should be installed so that it aligns with
adjacent drawer handles, or 4-1/2" max. from the
top of the panel. Secure the handle in the same
manner as cabinet handles. Screws must be
countersunk into the panel.
STEP 6 INSTALL ASSEMBLED PANEL
• Secure the panel to the door by inserting the top
and bottom mounting screws with spacers into
the matching keyhole slots.
• Make sure all 4 spacers engage the keyhole slots.
• P ress the panel against the door and push
downward until the spacers are f ully engaged
into the key hole slots. The panel should align
evenly with the top and sides.
• Stand the dishwasher upright.
• Open dishwasher door and drive the supplied
#8 x 1-3/4" truss head screws. Drive one screw at
the top and one on each side as shown, through
the inner door and into the custom panel.
WARNING: Do not overtighten screws. Excessive
tightening of the screws could damage door edges.
STEP 3 ALIGN TEMPLATE TO PANEL
• T rim template on the dotted line along all sides.
• P lace the template on the panel aligned with the top edge and
the centerline. Use tape to hold in place.
IMPO RT ANT: If t he templa te is not aligned with the t op edge o f the
panel, the 1/2" minimum ga p will not be maint ained. T his 1/2" minimum
gap must be maint ained t o prevent condensa tion and dama ge to the
co ntro l panel f rom sc rew heads.
• Use an awl to mark the screw hole locations indicated on the
template. Remove the template.
HEIGHT
Panel height must be between 30-1/16" and 30-1/4" .
• If the panel height is more than 30-1/4" it will
prevent the door from swinging open.
• If the panel height is less than 30-1/16" it will not
cover the dishwasher door frame.
Minimu m 1/2" Gap
for Cle arance
Cou nterto p
1/2" min.
PART S INC LUDED:
(4) Spa ce rs
(4) #8 x 5/8" Phillips t russ hea d st a inl ess st e el screws
(3) #8 x 1-3/4" Phil lips t russ hea d st a inl ess st e el
wood scr e ws
(2) Hea vy dut y springs
STEP 1 CUSTOM PANEL SIZE REQUIREMENTS
If the panel is less than 3/4" thick, shorter screws must
be used. Use #8 x 1/2" screws for 1/2" thick panels (not supplied).
• Use a 3/32" drill bit to drill pilot holes 3/32" deep in the marked
locations.
Note : T he custom panel is secured to the dishwasher door with
the spacers and screws provided. The spacer will slip into the
keyhole slots on the dishwasher door.
• Drive the supplied #8 x 5/8" Phillips truss head steel screws
through the spacer and into the panel.
• Install remaining spacers and screws as indicated in the marked
locations.
4-1/2" M ax.
Fr om Top
of Panel
Han dle
Cu stom
Door Panel
Screws Mu st
Be Countersu nk
In to Pan el
Cu stom
Panel
Sh ou lder Washers
Engage Keyhole
Slots
Dish wash er
Door
Cu stom
Panel
Screw
Spacer
IMPO RT AN ensur e optimum door balanc eT: T o
perf ormance, the c ustom pa nel must not weigh mo re
tha n 14 lbs.
STEP 7 INSTALL DOOR SPRINGS
The dishwasher is shipped from the factory with a
temporary set of balance springs. Use the heavy duty
springs provided and the adjustment holes in the
cable to balance the door after the cus tom panel
is ins talled onto the dishwasher.
• With the dishwasher on the wood skid, close and
latch the door.
• Remove and discard both door springs.
• Attach the new heavy duty door springs. Engage
the end with the short hook into the support leg
and the long hook into the cable.
• Open and close the door.
• If the door drops open when released, increase
spring tension. If the door closes when released,
decrease tension.
T IP: If the d oor d oes no t open easil y or falls to o
qui ckly, check spring cabl e rou ting. The cable is he ld
in place by “sh oulde rs” on the pu lley. Chec k to b e
sure the c able has no t slip ped ov er the pull ey
shou lde rs.
IMPOR NTT A : Adjust both b alance spri ngs to the
sam e am ount o f tensio n to p revent excessiv e door
twistin g dur ing u se.
Corre ct Sprin g
Cable Routin g
Increase
Tension
Decrease
Tension
Pulley
Shoulder
Use T his
Mou nting
Hole
23-3/4"
30-1/16 " Min .
30-1/4" Max.
• T he top of the custom panel must be flush
with the top of the door. T he 1/2" minimum gap
between the top of the door and the bottom of the
countertop must be maintained.
WIDTH
Panel widt h must be 23-3/4" .
• If the panel width is less than 23-3/4" it will not
cover the dishwasher frame.
For Reference Only
Not to Scale
Order GE Pub. No. 031-30569-1
Call 1-800-626-2000
For a full-size panel template with complete
panel installation instructions.
PDWT502VII
GE Profile™ Series Dishwasher with SmartDispense™ Technology
Specification Revised 3/13 250244
For answers to your Monogram,
® Profile™
Series or GE® appliance questions, visit our
website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
Features and Benefits
• 5-stage filtration with Piranha™ hard food disposer - 5 self-cleaning filters ensure
clean dishes
• Dedicated silverware jets - Highly pressurized spray jets target the silverware area for
improved cleaning
• Deep Clean cycle with Steam Prewash - Removes tough, baked-on soils like egg, rice
and oatmeal
• Top rack only selection - Upper rack only cycle uses less water than a full load
• Fan assist dry with heated option and ActiveVent - A heating element heats the air
inside while a hidden fan circulates the warm air to help dry dishes
• 48 dBA sound level - Nearly silent two-pump system cleans dirty dishes without
disruption
• ENERGY STAR® qualified and CEE Tier II rated - Meets or exceeds federal guidelines for
energy efficiency for year-round energy and money savings
• Eclipse black full-extension racks with ball-tip tines - Durable racks glide smoothly on
ball-bearings for easy loading
• Lower rack fold-down tines - Flexible loading options handle today's dishes and
cookware of all shapes and sizes
• SmartDispense™ technology - Conveniently stores up to 47 oz of liquid detergent and
automatically dispenses multiple doses in each cycle
• Upper rack deep bowl tines - Even oversized bowls fit perfectly in the top rack for
easy cleaning
• Flexible racks - Designed for today's dishes and holds up to 16-place settings
• Two-pump system - One small pump for washing/rinsing and one small pump to
remove soils provide excellent wash performance with reduced sound
• Model PDWT502VII - Custom panels required
PDWT502VII
GE Profile™ Series Dishwasher with SmartDispense™ Technology
Specification Revised 3/13 250244

Specyfikacje produktu

Marka: GE
Kategoria: pralka
Model: Profile PDWT502VII

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE Profile PDWT502VII, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje pralka GE

GE

GE GSD3715FAA Instrukcja

15 Października 2024
GE

GE GSD6700GCC Instrukcja

14 Października 2024
GE

GE GLD5706VCC Instrukcja

8 Października 2024
GE

GE GLDL500NCC Instrukcja

7 Października 2024
GE

GE Profile PDWT500PWW Instrukcja

6 Października 2024
GE

GE GSD2200GWW Instrukcja

6 Października 2024
GE

GE GSD3300NWW Instrukcja

6 Października 2024
GE

GE GSD2020ZBB Instrukcja

4 Października 2024
GE

GE GSD2000FAD Instrukcja

4 Października 2024
GE

GE GTW485ASWWB Instrukcja

3 Października 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Candy

Candy CS 15102D3-80 Instrukcja

15 Października 2024
Siemens

Siemens iQ700 WI14W540EU Instrukcja

15 Października 2024
LG

LG WTP22BK Instrukcja

15 Października 2024
Freggia

Freggia WTIE148 Instrukcja

15 Października 2024
Freggia

Freggia WISE126R Instrukcja

15 Października 2024
Freggia

Freggia WISE126B Instrukcja

15 Października 2024
Freggia

Freggia WISE126 Instrukcja

15 Października 2024
Freggia

Freggia WISA105 Instrukcja

15 Października 2024
Freggia

Freggia WISA106 Instrukcja

15 Października 2024
Freggia

Freggia WIA107 Instrukcja

15 Października 2024