Instrukcja obsługi GE Profile PD900DPBB

GE piekarnik Profile PD900DPBB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE Profile PD900DPBB (24 stron) w kategorii piekarnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/24
1
31-10829GE10-11
BEFORE YOU BEGIN
Read these in struc tions care ful ly and completely.
IMPORTANT Savetheseinstructionsfor
localinspector’suse.
IMPORTANT Observeallgoverning
codesandordinances.
Note to Installer Besuretoleavethese
instructionswiththeconsumer.
Note to Consumer Keeptheseinstructionsfor
futurereference.
Skill level –Installationofthisappliancerequiresa
qualifiedinstallerorelectrician.
Properinstallationistheresponsibilityoftheinstaller.
ProductfailureduetoimproperinstallationisNOT
coveredunderthewarranty.
30” Electric
Drop-In Ranges
Installation
Instructions
Questions?Call800.GE.CARES(800.432.2737)orVisitourWebsiteat:www.GEAppliances.com.
InCanada,call1.800.561.3344orvisitwww.GEAppliances.ca.
ATTENTION INSTALLER: Allelectricdrop-inrangesmustbehardwired(directwired)intoan
approvedjunctionbox.AplugandreceptacleisNOTpermittedontheseproducts
.
FOR YOUR SAFETY
WARNINGBeforebeginningtheinstallation,switchpoweroffattheservicepanelandlockthe
servicedisconnectingmeanstopreventpowerfrombeingswitchedonaccidentally.Whentheservice
disconnectingmeanscannotbelocked,securelyfastenaprominentwarningdevice,suchasatag,totheservice
panel.
WARNINGTheinformationinthismanualmustbefollowedtominimizetheriskoffire,electricshock,
ortopreventpropertydamage,personalinjuryorlossoflife.
MATERIALS YOU MAY NEED
JunctionBox
WireNuts
StrainReliefClampfor1/2”Conduit
TOOLS YOU MAY NEED
1/8”DrillBitandElectricDrill PhillipsScrewdriver
Level FlatheadScrewdriver
TapeMeasure 1/4”NutDriver
StraightedgeorSquare Hammer
HandorSaberSaw Pencil
SafetyGlasses
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed
and engaged.
Ensure the anti-tip bracket is -engaged when the range re
is moved.
Do not operate the range without the anti-tip bracket in
place and engaged.
Failure to follow these instructions can sult in death or re
serious burns children or adults.to
Tip-Over Hazard
WARNING
Oven
Anti-Tip Bracket
Countertop or
Wood Block
Rear
Wall
2
InstallationInstructions
Failuretoremovepackagingmaterialscouldresultindamagetotheappliance.Removeallpackingpartsfrom
oven,racks,andheatingelements.Removeprotectivefilmandlabelsontheouterdoorandcontrolpanel.
Alsoremoveplasticontrimsandpanelandalltapearoundtheoven.Openovendoorandremoveliterature
packandovenracks.Removethebottomtrimfromthesideoftheoven.Itwillbeinstalledattheendofthe
installationprocess.Thetrimiswrappedseparatelyinaplasticbagwhichwillalsocontainthe4screwsto
securethebottomtrimandthe2shoulderscrewsusedtosecuretheproducttothecabinet.
1REMOVE PACKAGING MATERIALS
Allow30”minimumclearance
betweensurfaceunitsandbottom
ofunprotectedwoodormetal
cabinet.Allowa24”minimum
whenbottomofwoodormetalis
protectedbynolessthan1/4”thick
flameretardantmillboardcovered
withnotlessthanNo28MSGsheet
metal(.015”),.015”thickstainless
steel,.024”aluminumor.020”
copper.
NOTE: Drop-In Ranges are designed to hang
from the countertop only. Do not install on a
platform or sup port rails.
2PREPARING THE OPENING (FOR INDOOR USE ONLY)
3
InstallationInstructions
2 PREPARING THE OPENING (Continued)
TheStandardInstallationofthisDrop-InRangeistohang
bythecountertoponthesidemetalflangesunderglass
cooktop.This Range must not be installed on a base or
sub structure (2”x 4” support).
Iftheconstructionofyourcabinetcannotprovidea
1/4”flatareaatthebackofthecountertopopening,
considerchangingthecountertoptoaccommodatethis
dimension.Iftheareaisnotflat,excesstensionmay
beappliedtotheglasscooktop,causingbreakageand
voidingthewarranty.
•Countertopthickness1-1/4”min.isrequiredtosupporttheproduct.Bracesmustbeinstalledbetweenthe
undersideofthecountertopandthecabinetifrequiredtoobtain1-1/4”minimumthickness(eachside).
•Makesurethewallcoverings,countersandcabinetsaroundtheovencanwithstandtheheat(upto200°F
(93.3°C)generatedbytheoven.
•Thisappliancehasbeenapprovedfor0”spacingtoadjacentsurfacesabovethecooktop.However,a6”
minimumspacingtosurfaceslessthan15”abovethecooktopandadjacentcabinetisrecommendedto
reduceexposuretosteam,greasesplatterandheat.
•Locatethewiringjunctionboxattherearofthecutout.Thedimensionfromthetopofthewiringjunction
boxtothecountertopmustbeaminimumof28-1/2”.Theboxmustnotextendmorethan3”offtheplane
ofthewall.Thejunctionboxmustbelocatedwhereitwillallowconsiderableslackintherangeconduit,so
thattherangecanbepulledoutforserviceifnecessary.
Wall
1/4”min.flat
23-3/16”
9/16”min.
flat
9/16”min.
flat
29-15/16”–30-1/16”
smoothcut
25”
typically 1/4”
R
Flat
area
Countertop
Rangesupport


Specyfikacje produktu

Marka: GE
Kategoria: piekarnik
Model: Profile PD900DPBB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE Profile PD900DPBB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje piekarnik GE

Instrukcje piekarnik

Najnowsze instrukcje dla piekarnik