Instrukcja obsługi GE Profile P2S975WEMWW

GE piekarnik Profile P2S975WEMWW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE Profile P2S975WEMWW (60 stron) w kategorii piekarnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/60
TOOLS YOU WILL NEED
1
MATERIALS YOU MAY NEED
31-10641-1 03-07 JR
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.361.3400 or Visit our Website at: www.geappliances.ca
Installation
Self-Cleaning Dual Fuel
Instructions
Slide-In Range
P2S975
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•IMPORTANT —Save these
instructions for local inspector’s use.
•IMPORTANT —Observe all
governing codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these
instructions for future reference.
•Product failure due to improper installation
is not covered under the Warranty.
WARNING —This appliance must
be properly grounded.
•Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
IN THE COMMONWEALTH OF
MASSACHUSETTS:
• This product must be installed by a
licensed plumber or gas fitter.
• When using ball-type gas shut-off valves,
they shall be the T-handle type.
• A flexible gas connector, when used, must
not exceed 3 feet.
PARTS INCLUDED
Anti-Tip Bracket
Anchor Sleeves
Lag Bolts
(For Concrete Floors Only)
Shut Off ValvePipe Fittings
CSA-Approved Flexible Gas Line
3/8″Min. ID, 1/2″NPT Connection,
3-foot Maximum Length (Massachusetts only)
Joint Sealant
Wrench or Pliers
(for 1-7/16” Nut)
Level
1/4” Nut Driver
Safety Glasses
Drill
Tape Measure
Screws
Rear Filler
2 Screws
Phillips Head
Screwdriver Pipe Wrench
Flat-blade
Screwdriver
2
Installation Instructions
FOR YOUR SAFETY:
WARNING — If the information
in this manual is not followed exactly, a fire,
explosion or gas leak may result causing
property damage, personal injury or death.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance!
WHAT TO DO IF YOU
SMELL GAS:
• Do not try to light any appliance. Do not
touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier,
call the fire department.
Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
IMPORTANT SAFETY INSTRUCTIONS
This range has been design certified by
UNDERWRITERS LABORATORIES for use in
the United States and Canada. You’ll find
safety precautions in your Owner’s Manual.
Read them carefully.
• Installation of this range must conform with
local codes or in the absence of local codes
with the National Fuel Gas Code, ANSI
Z223.1–Latest edition.
• Be sure your range is installed properly by
a qualified installer or service technician.
• To eliminate reaching over surface burners,
cabinet storage above burner should be
avoided.
• Do not install the unit near an outside door
or where a draft may affect its use.
3
Installation Instructions
ANTI-TIP DEVICE
WARNING —To reduce the risk
of tipping, the appliance must be secured by
properly installed Anti-Tip bracket packed
with this appliance.
If the Anti-Tip device supplied with the range
does not fit this application, use the universal
Anti-Tip device WB2X7909. Skip Steps 4, 19
and 21.
To check if the bracket is installed and
engaged properly, carefully tip the range
forward. The anti-tip bracket should engage
and prevent the range from tipping over.
WARNING —
• All ranges can tip
• Injury to persons could result
• Install Anti-Tip bracket packed
with range
• See Installation Instructions
If you pull the range out and away from the
wall for any reason, make sure the Anti-Tip
bracket is engaged when the range is pushed
back against the wall.
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the
proper voltage and frequency and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse
having a recommended amperage rating per
the table below.
BREAKER OR FUSE SIZE
240V 40 Amps
208V 40 Amps
NOTE: Check Local Codes for required
breaker size.
Rating plate is located above the storage
drawer below the oven frame.
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have
the electrician show you where your main
range disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to
wire your range according to governing
codes could result in a hazardous condition.
If there are no codes, your range must be
wired and fused to meet the requirements of
the National Electrical Code, ANSI/NFPA No.
70–Latest edition. You can get a copy by
writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a four-conductor
connection to an electric range. When installing
an electric range in new construction, a mobile
home, recreational vehicle or an area where
local codes prohibit grounding through the
neutral conductor, follow the instructions in the
section on NEW CONSTRUCTION AND FOUR-
CONDUCTOR BRANCH CIRCUIT
CONNECTION.
In Canada your range must be wired and
fused to meet the requirements of the
Canadian Electrical Code.
You must use a three-wire, single-phase
A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system.
FOR YOUR SAFETY:
WARNING — For personal safety,
remove house fuse or open circuit breaker
before beginning installation. Failure to do so
could result in serious injury or even death.
All rough-in and spacing dimensions must be
met for safe use of your range. Electricity to
the range can be disconnected at the outlet
without moving the range if the outlet is in
the preferred location (remove lower drawer).
To reduce the risk of burns or fire when
reaching over hot surface elements, cabinet
storage space above the cooktop should be
avoided. If cabinet storage space is to be
provided above the cooktop, the risk can
be reduced by installing a range hood that
protrudes at least 5” beyond the front of the
cabinets. Cabinets installed above a cooktop
must be no deeper than 13”.
Be sure your appliance is properly installed
and grounded by a qualified technician.
Rating
plate location

Specyfikacje produktu

Marka: GE
Kategoria: piekarnik
Model: Profile P2S975WEMWW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE Profile P2S975WEMWW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje piekarnik GE

GE

GE JBS08PICWW Instrukcja

14 Stycznia 2025
GE

GE Profile JP939CHCC Instrukcja

13 Stycznia 2025
GE

GE JSP26BDWH Instrukcja

13 Stycznia 2025
GE

GE Profile JBP99SHSS Instrukcja

13 Stycznia 2025
GE

GE 169140 Oven Instrukcja

12 Stycznia 2025
GE

GE Profile Spectra JB940TDWW Instrukcja

12 Stycznia 2025
GE

GE Profile PSB9100SVSS Instrukcja

27 Grudnia 2024
GE

GE Profile PSB9120SVSS Instrukcja

27 Grudnia 2024
GE

GE Profile PT9900SWSS Instrukcja

27 Grudnia 2024
GE

GE PSA1200 Instrukcja

15 Grudnia 2024

Instrukcje piekarnik

Najnowsze instrukcje dla piekarnik

Whirlpool

Whirlpool ACMT 5131 Instrukcja

15 Stycznia 2025
Miele

Miele H 4130 E Instrukcja

15 Stycznia 2025
Siemens

Siemens HB65AB522 Instrukcja

15 Stycznia 2025
AEG

AEG Competence 30480 B W Instrukcja

15 Stycznia 2025
AEG

AEG Competence B4100-a Instrukcja

15 Stycznia 2025
Siemens

Siemens HB78AA770 Instrukcja

15 Stycznia 2025
Indesit

Indesit FE10 K Instrukcja

15 Stycznia 2025
Siemens

Siemens he 33au540 Instrukcja

15 Stycznia 2025
Miele

Miele h 310 1 b Instrukcja

15 Stycznia 2025
Whirlpool

Whirlpool AKZ 152 Instrukcja

15 Stycznia 2025