Instrukcja obsługi GE Profile JSP40AWAA

GE piekarnik Profile JSP40AWAA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE Profile JSP40AWAA (7 stron) w kategorii piekarnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/7
INSTALLATION INSTRUCTIONS FOR YOUR NEW
30" ELECTRIC SLIDE-IN RANGE
Before you begin - Read these instructions completely and carefully.
IMPORTANT - Save these instructions for local inspector’s use.
IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer - Be sure to leave these instructions with the Consumer.
Note to Consumer - Keep these instructions with your Use and Care Book for
future reference.
NOTE: This appliance must be properly grounded.
• All Ranges Can Tip
• Injury To Persons Could
Result
• Install Anti-tip Device Packed
With Range
• See Installation Instructions
WARNING
FOR YOUR SAFETY
1
CAUTION: For Personal
Safety remove house fuse or
open circuit breaker before
beginning installation. Failure
to do so could result in
serious injury or even death.
All rough-in and spacing dimensions must be
met for safe use of your range. Electricity to the
range can be disconnected at the outlet without
moving the range if the outlet is in the preferred
location (remove lower drawer).
To reduce the risk of burns or re when reaching
over hot surface elements, cabinet storage
space above the cooktop should be avoided. If
cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing
a range hood that sticks out at least 5" beyond
the front of the cabinets. Cabinets installed
above a cooktop may be no deeper than 13".
Be sure your appliance is properly installed and
grounded by a qualied technician.
WARNING: To reduce the risk
of the thetipping appliance,
appliance must be secured by
properly installed anti-tip device
packed with the appliance.
INSTALLATION OF THE
ANTI–TIP DEVICE
Before placing range in the counter, check the
factory location of the stability device on the
back of the range. For convenience you can
hook the stability chain in the upper set of
holes. Make sure there is no structural
interference when using the upper set of holes.
Remove all parts from the plastic bag found
inside the prepack of the oven and save
packaging tape.
STABILITY DEVICE
Fig. 1
INT303-6
Pub No. 31-10070
1. Decide on a location
that has no electrical
wiring or plumbing.
2. With the long screw
provided anchor the
chain to the oor or
wall.
3. Make sure the screw
is going into the wall
plate or stud at the
base of the wall at
least 3/4".
4. Attach the stability
chain so that it lines
up with the bracket on the back of the range.
5. Tug the chain to make sure it is securely
fastened.
6. Take the packaging tape
and temporarily attach
the loose end of the chain
to the rear of the
countertop.
7. Slide the range into the
counter leaving enough
space behind to attach
the chain to the bracket.
8. Slip the nearest
link of the chain
onto the bracket.
Pull to make sure it
is as snug as
possible.
9. Slide the range all
the way back. It is
normal to have
some slack in the
chain, but it should
not be excessive.
• The distance from the floor to the top of the
counter must be at least 35 7/8". The
maximum counter height is 38".
• 30" ranges conform to U.L. requirements for
0" spacing from vertical walls above
countertops. However, some kitchen cabinet
finishes can be damaged by heat from the
range surface elements. Where varnished
wood or plastic film finishes are used, a
minimum clearance of 6" must be maintained.
• For listed over-the-range microwave ovens,
the microwave ovens can be installed above
the cooktop as per manufacturer's installation
instructions.
• The range may be placed with 0" clearance
(flush) at the back wall and side walls if the
range side trims extend beyond the cabinet
fronts at least 1/4".
• See Figures 1 and 2 for all rough-in and
spacing dimensions. These dimensions must
be met for safe use of your range. The
location of the electrical outlet may be
changed as needed, but electricity to the
range can be disconnected at the outlet
without moving the range if the outlet is in the
suggested location (remove lower drawer).
2
18" MIN
30" MIN 6"
MIN
0" 0"
TAPE
MINIMUM CLEARANCES
TOOL LIST
• Hand or electric drill
• Hand or saber saw
• Pencil
• Tape measure
• Straightedge
• 1/8" drill bit
Fig. 6
MINIMUM DIMENSIONS BETWEEN COOKTOP
AND CABINETS OR WALLS
3
PREPARING THE COUNTER
FIG. 7
• The distance from the oor to the top of the
counter must be at least 35 7/8". The
maximum countertop height is 38".
Make sure the wall coverings, countertop and
cabinets around the cooktop can withstand the
heat (up to 200°F) generated by the range.
NOTE: Dimension for Wall to Front of Door
Handle (door closed).
*-28" FOR MODELS- JSP26, JSS26, JSC26,
JSS16, RS734, RS504
**- 28 1/2" FOR MODELS- JSP39, JSP38,
JSP31, JSP28,
RS744, RS622,
JS960, JSP40,
JSP34
REMOVING PACKAGING
MATERIAL
Any packaging materials must
be removed during installation.
This will include adhesive tape, wire ties,
cardboard and protective plastic. Failure
to remove these materials could result in
damage to the appliance once the
appliance has been turned on and
surfaces have heated.
•Remove all tape and packaging. Be sure to
remove clear plastic film that covers some
chrome parts (around glass oven doors, side
trim) and any tape and packaging from inside
the oven.
• Take the accessory pack out of the oven.
• Check to be sure that no range parts have
come loose during shipping.
PREPARATION
If you have an existing 30" wide cutout that goes
all the way to the wall, you have the option to buy
a 4" Backguard, Model #JXS31 (white), JXS32
(chrome), JXS33 (almond), JXS34 (black), or
JXS35 (bisque) or a Main Top Rear Filler Kit,
Model # JXS62BB (black), JXS63WW (white),
JXS64AA (almond), or JXS65CC (bisque).
These kits are available through your GE dealer,
if the existing cutout is in a counter that has a
backsplash (postformed top) we recommend that
you use the 4" backguard kit.
FIG. 8
Determine the dimension of your cutout. See
Fig. 9 and Fig. 10. Dimensions given are from
front of counter and not from cabinet face. To
minimize chipping you may want to apply
masking tape to the counter and mark the cut on
top of the tape. Use a hand or saber saw to
make the cut. For best appearance it is
important that the cut be smooth and straight.
If you are NOT using the Filler or Backguard:
If you have a countertop deeper than 25" and
you wish to set the range further back into the
counter, the cutout may be cut deeper (up to 24
1/2"), but there must be at least 24 1/2" from the
front edge of the countertop and back wall.
FIG. 9
23 3/16"
30"

Specyfikacje produktu

Marka: GE
Kategoria: piekarnik
Model: Profile JSP40AWAA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE Profile JSP40AWAA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje piekarnik GE

GE

GE JBS08PICWW Instrukcja

14 Stycznia 2025
GE

GE Profile JP939CHCC Instrukcja

13 Stycznia 2025
GE

GE JSP26BDWH Instrukcja

13 Stycznia 2025
GE

GE Profile JBP99SHSS Instrukcja

13 Stycznia 2025
GE

GE 169140 Oven Instrukcja

12 Stycznia 2025
GE

GE Profile Spectra JB940TDWW Instrukcja

12 Stycznia 2025
GE

GE Profile PSB9100SVSS Instrukcja

27 Grudnia 2024
GE

GE Profile PSB9120SVSS Instrukcja

27 Grudnia 2024
GE

GE Profile PT9900SWSS Instrukcja

27 Grudnia 2024
GE

GE PSA1200 Instrukcja

15 Grudnia 2024

Instrukcje piekarnik

Najnowsze instrukcje dla piekarnik

Whirlpool

Whirlpool WOI4S8HM1SXA Instrukcja

25 Marca 2025
AEG

AEG NBU5A20SB Instrukcja

24 Marca 2025
AEG

AEG NBU5P40BCK Instrukcja

24 Marca 2025
AEG

AEG TA5PB53WAB Instrukcja

24 Marca 2025
AEG

AEG OU5AE20AK Instrukcja

24 Marca 2025
AEG

AEG TU5AB20SCK Instrukcja

24 Marca 2025
AEG

AEG TB8SB631AB Instrukcja

24 Marca 2025
AEG

AEG TU5PB40NCK Instrukcja

24 Marca 2025
AEG

AEG TU5PB40NSK Instrukcja

24 Marca 2025
AEG

AEG TR6PB531SB Instrukcja

24 Marca 2025