Instrukcja obsługi GE JX9153DJBB

GE Magnetron JX9153DJBB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE JX9153DJBB (8 stron) w kategorii Magnetron. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
Installation Microwave Oven
Instructions Built-In Trim Kits
1
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT — Save these instructions
for local inspector’s use.
• IMPORTANT — Observe all governing codes
and ordinances.
• Note to Installer – Be sure to leave these instructions
with the Consumer.
• Note to Consumer – Keep these instructions for future
reference.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• This kit is for use on models:PEB9159DJ, PEB9159SJ,
PEB9159EJ, CEB1599SJ.and CEB1599EL.
• This kit and microwave are approved for installation
alone or above any single electric wall oven. Do not
mount adjacent (within 2 feet) to any range, cooktop,
gas oven, or other microwave.
• This product is to be installed 3 feet above floor level.
• Do not alter or modify any part of this kit or the oven.
• For easier installation and personal safety, we
recommend that two people install this microwave
oven.
• Unplug the microwave oven before attempting
installation of this kit.
WARNING
— This oven must be plugged into a
properly grounded 3-hole, 120 volt receptacle as required
by the National Electrical Code.
WARNING
— Before beginning the installation,
switch power off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
Questions? Call GE Appliances Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com
PARTS INCLUDED
NOTE: This kit has extra screws to prevent the
technician from spending extra time locating
a replacement in case they lose one during
installation.
JX9152 and JX9153
PART QUANITY
Rear Duct 1
Bottom Duct
1
Trim Kit
Frame 1
Rail
2
Short Screws
16 required
3 extra
Long Wood
Screws 4 required
2 extra
CUTOUT DIMENSIONS
WARNING
— This trim kit uses air flow from the top, bottom and
sides of the trim frame. Blocking the air flow can
cause the microwave to function improperly and may
cause damage to the microwave.
Allow a 1” clearance beyond the edge of the trim kit
frame to provide proper air flow.
FOR INSTALLATION ABOVE A BUILT-IN OVEN:
Microwave oven should be installed on a 3/8”
plywood base and supported by 2x4 or 1x2
equivalent runners on all sides. Base must be
capable of supporting a minimum of 100 lbs.
2
Installation Instructions
Min. depth with receptacle outside cutout – 22
”
Min. depth with receptacle inside cutout – 23 1/2
”
120 volt – 60 Hertz grounded power receptacle.
TOOLS YOU WILL NEED
Ŷ
2 Phillips Screwdrivers (#1 & #2)
Ŷ
Drill with 3/32” Drill Bit
Ŷ
Pencil
Ŷ
Level
Ŷ
Tape Measure
Depth
Height
1” Overlap
Width
1” Overlap
1” Clearance beyond
trim frame
(on all sides)
3” Min.
27”models: 1 7/8” overlap
30”models: 3 5/16” overlap
Bottom of trim kit must be
minimum of 36” from floor
Dimen-
sion
Trim Kit Cutout
27” 30”
Height 19 1/8” 19 1/8” 17 1/8 ± 1/ ”8
Width 26 7/8” 29 3/4” 23 1/4 ± 1/ ”8
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event
of an electrical short circuit, grounding reduces
the risk of electric shock by providing an escape
wire for the electric current. This appliance
is equipped with a cord having a grounding
wire with a grounding plug. The plug must be
plugged into an outlet that is properly installed
and grounded.Consult a qualified electrician or
serviceman if the grounding instructions are not
completely understood, or if doubt exists as to
whether the appliance is properly grounded.
Improper use of the
grounding plug can
result in a risk of
electric shock.
Do not use an
extension cord. If the
power supply cord
is too short, have a
qualified electrician
or serviceman install
an outlet near the
appliance.
Permanent and Correct Installation
3-Prong plug
Grounding pin
3-Prong receptacle
Grounded receptacle box
WARNING
ELECTRICAL REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 14
amps and 1.60 kilowatts. This product must
be connected to a supply circuit of the proper
voltage and frequency. Wire size must conform
to the requirements of the National Electrical
Code or the prevailing local code for this kilowatt
rating. The power supply cord and plug should
be brought to a separate 15 to 20 ampere
branch circuit single grounded outlet. The outlet
box should be located in the cabinet above the
oven. The outlet box and supply circuit should be
installed by a qualified electrician and conform
to the National Electrical Code or the prevailing
local code.
2
INSTALL THE RAILS
Disconnect the microwave oven from the receptacle.
Remove everything out of the microwave oven, including
packing, Owner’s Manuals, turntable and turntable
support. A protective film has been applied to some
microwave oven and trim kits. If applied, remove the film.
Turn over the microwave oven and secure the rails to
oven Base Plate by inserting 4 short screws. Be careful
not to scratch the microwave oven.
1
LOCATE AND INSTALL THE BASE
PAN
Set Base Pan into the front cabinet microwave
oven cutout and center it right and left. Push back
until the front flange is against the cabinet front wall.
Mount the Base Pan using 3 short screws.
3
Installation Instructions
Short
Screw
Microwave
Oven Bottom
Rail
Short
Screw
Flanges Door
Base Pan
Mounting Holes
3
INSTALL THE REAR DUCT
1. Gently return microwave oven to its upright position.
2. Remove screw A.
3. Align the rear duct with the back of microwave oven,
as shown.
4. Slide 2 tabs into the slots on the right side of the back
of microwave oven.
5. Use 2 short screws to secure top of rear duct to the
back of microwave oven, as shown.
A. Rear duct tabs
B. Slots
A B
A. Short screws (2)
B. Rear duct
C. Back of microwave oven
ABC
Screw A

Specyfikacje produktu

Marka: GE
Kategoria: Magnetron
Model: JX9153DJBB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE JX9153DJBB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Magnetron GE

GE

GE Profile JVM1661WB Instrukcja

11 Października 2024
GE

GE GCST09N1 Instrukcja

8 Października 2024
GE

GE GCST11N1 Instrukcja

8 Października 2024
GE

GE Adora HDM1853SL Instrukcja

13 Września 2024
GE

GE JX36BDS Instrukcja

11 Września 2024
GE

GE JX36DWW Instrukcja

11 Września 2024
GE

GE JX36BES Instrukcja

10 Września 2024
GE

GE SCA1001HSS Instrukcja

10 Września 2024
GE

GE Adora HDM1853BL Instrukcja

8 Września 2024
GE

GE JX9153DJBB Instrukcja

7 Września 2024

Instrukcje Magnetron

Najnowsze instrukcje dla Magnetron

Sharp

Sharp R-939IN Instrukcja

11 Października 2024
Kenwood

Kenwood K20MSS10 Instrukcja

11 Października 2024
Belion

Belion PCM100 Instrukcja

11 Października 2024
Sharp

Sharp R-875 Instrukcja

10 Października 2024
Caso

Caso C1800M Instrukcja

10 Października 2024
G3 Ferrari

G3 Ferrari G10030 Instrukcja

10 Października 2024
Melissa

Melissa 16330129 Instrukcja

9 Października 2024
Hisense

Hisense H23MOBS5HUK Instrukcja

9 Października 2024
Cecotec

Cecotec GrandHeat 2550 Built-in Instrukcja

9 Października 2024
Beko

Beko MOC20240G Instrukcja

9 Października 2024