Instrukcja obsługi GE JX1830BB

GE Magnetostrykcja JX1830BB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GE JX1830BB (4 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
PART QUANTITY
Trim Frame 1
Bottom Duct 1
Side Duct 1
1” Screws 6
(4 required, 2 extra)
1/2” Screws 15
(11 required, 4 extra)
Anti-Tip Bracket 1
Bottom Bracket 1
Upper Duct 1
Template 1
PARTS INCLUDED
Questions? Call GE Answer Center at 800.626.2000
or Visit our Website at:
www.GEAppliances.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions
JX1827 and JX1830
Read these instructions completely and carefully.
•IMPORTANT –Save these
instructions for local inspector’s use.
•IMPORTANT –Observe all
governing codes and ordinances.
•Note to Installer –Be sure to leave these
instructions with the Consumer.
•Note to Consumer –Keep these
instructions for future reference.
BEFORE YOU BEGIN
• Unplug the microwave oven before attempting
installation of this kit.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• This kit is UL listed for installation alone or over any
General Electric/Hotpoint/RCA single electric wall
oven.
TOOLS YOU WILL NEED
Phillips screwdriver
Pencil
Tape measureAwl or punch
Drill with 7⁄64″bit or #35
1
FOR YOUR SAFETY:
WARNING –Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
2
CUTOUT DIMENSIONS1.
* Min. depth with receptacle outside cabinet 191⁄2″
Min. depth with receptacle inside cabinet 22″
Installation Instructions
Models 27″ ″30
Height 163⁄ 164″3⁄4″
Width 251⁄ 252″1⁄2″
Depth (min.)* 191⁄ 192″or 22″1⁄2″or 22″
On 27 models, allow 1 at the top, ″ ″ 11⁄16″on the sides
and 13⁄8″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
On 30 models, allow 1 at the top, 2″ ″ 3⁄16″on the sides
and 13⁄8″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
Depth
Height
3 Min.″
Width
INSTALL BOTTOM BRACKET
AND BOTTOM DUCT
2.
Disconnect the microwave oven before proceeding
with the installation.
Fasten the bottom bracket to the bottom duct by
using two 1⁄2″screws.
Remove any loose items inside the microwave
oven, including the turntable and turntable
support. Carefully turn the microwave upside
down.
Install bottom duct with four 1⁄2″screws as shown.
A
C
B
D
Front
Rear
1⁄2″Screws (2)
Screws
Screws
Microwave Oven Upside Down
3
Installation Instructions
INSTALL THE ANTI-TIP BRACKET3.
Fold or cut the front edge of the template, along
the front guide line. Place the template flush along
the front edge of the cutout floor, aligning the
center line of the template with the center line of
the cutout floor. Mark the center positions with an
awl or center punch for the anti-tip bracket
location as shown.
Remove the template and drill two holes for the
anti-tip bracket.
Install the anti-tip bracket onto the cutout floor
using two 1⁄2″screws.
A
B
C
Cutout Floor
1⁄2″Screws (2)
Anti-Tip Bracket
INSTALL SIDE DUCT AND UPPER
DUCT
4.
Connect the side duct to the upper duct as shown.
1. Insert projecting tabs of the upper duct into the
holes of the side duct.
2. Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the
microwave oven before the ducts are attached.
Set the microwave upright, being careful not to
bend the front flange. Remove the one existing
screw from the left side of the microwave oven.
Peel off the backing of the double sided tape.
Carefully position the side duct and upper duct
assembly on the microwave cabinet, aligning with
the bottom screw hole. Press down firmly on the
ducts. Fasten the duct assembly to the left side of
the cabinet with the screw removed above.
B
A
(2)
C
Existing Screw (1)
(1)
Upper Duct
Side Duct
3 Tabs
3 Holes

Specyfikacje produktu

Marka: GE
Kategoria: Magnetostrykcja
Model: JX1830BB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GE JX1830BB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Magnetostrykcja GE

GE

GE JX36DBB Instrukcja

8 Grudnia 2024
GE

GE JX827BN Instrukcja

8 Grudnia 2024
GE

GE Café CX152P4MWM Instrukcja

8 Grudnia 2024
GE

GE JX827SS Instrukcja

8 Grudnia 2024
GE

GE JX1830BB Instrukcja

8 Grudnia 2024
GE

GE JX1527MSA Instrukcja

8 Grudnia 2024
GE

GE JX36CBB Instrukcja

8 Grudnia 2024
GE

GE JX2027DMBB Instrukcja

8 Grudnia 2024
GE

GE JX2027DMWW Instrukcja

8 Grudnia 2024
GE

GE JX7227BLTS Instrukcja

8 Grudnia 2024

Instrukcje Magnetostrykcja

Najnowsze instrukcje dla Magnetostrykcja

Midea

Midea MM720CGE Instrukcja

10 Grudnia 2024
Continental Edison

Continental Edison CEMO20EBM Instrukcja

10 Grudnia 2024
Gorenje

Gorenje ECT631BSC Instrukcja

9 Grudnia 2024
Gorenje

Gorenje ECT693ORAB Instrukcja

9 Grudnia 2024
Gorenje

Gorenje ECS691USC Instrukcja

9 Grudnia 2024
Gorenje

Gorenje MO23ORAW Instrukcja

9 Grudnia 2024
Insignia

Insignia NS-MW7RC5 Instrukcja

9 Grudnia 2024
Haier

Haier JM-V16G Instrukcja

9 Grudnia 2024
Haier

Haier JM-17K Instrukcja

9 Grudnia 2024
Siemens

Siemens BE555LMS0W Instrukcja

8 Grudnia 2024