Instrukcja obsługi Garmin Nüvi 260

Garmin nawigator Nüvi 260

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin Nüvi 260 (28 stron) w kategorii nawigator. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/28
vi® 200-Series Bicycle Mount
Instructions 2–3 ………………………
Instructions (Français) 4–5 ………….
Istruzioni 6–7 ………………………
Anweisungen 8–9 ……………………
Instrucciones 10–11 ………………….
Instruções 12–13 ……………………..
Instructies 14–15 ……………………..
Instruktioner 16–17 …………………..
Ohjeet 18–19 ………………………
Instruksjoner 20–21 ………………….
Instruktioner 22–23 …………………..
Инструкции………… ……… 24–25
2-EN
InstructIons
The nüvi
®
200-series bicycle mount allows
you to attach your nüvi to your bicycle.
Garmin
®
s standard Limited Warranty
applies to this accessory. Refer to the limited
warranty and safety warnings in your nüvi Set
Up and Go guide before installing the bicycle
mount.
Do not expose the nüvi to caution:
water. Contact with water can cause the
nüvi to malfunction.
warning: You are responsible for
obeying all trafc laws when using your
nüvi on your bicycle, scooter, or other
vehicle with handlebars.
You can install the bicycle mount to the stem
or handlebars. The stem installation (shown
here) provides a more sturdy location. The
optional wedge should be used under the
mount for a better viewing angle.
To attach the bicycle mount to your
bicycle stem:
1. Insert the hard plastic half of the bicycle
mount into the half with the rubber
backing.
Release lever
Bike mount
Wedge (optional)
EN-3
For horizontal bars: Separate and
remove the top part of the mount, turn it
90 degrees, and replace. Continue with
step 2.
2. Place the wedge on the bicycle stem,
and then place the bicycle mount on
the wedge. Make sure the release lever
is on the left.
3. Thread the two cable ties through the
two slots on the bicycle mount. Position
the mount on your bicycle and attach
using the cable ties.
Release
lever
Cable ties
To attach the cradle to the bicycle
mount:
1. Fit the bottom of the nüvi in the cradle,
and snap the top of the nüvi into place.
2. Align the cradle with the bicycle mount.
3. Slide the cradle left onto the bicycle
mount until it snaps into place.
Change the Usage Mode on your TIP:
nüvi. Touch > > > Settings System
Usage Mode Bicycle > .
To release the cradle:
1. Remove the nüvi from the cradle.
2. Press down on the release lever, and
slide the cradle to the right.


Specyfikacje produktu

Marka: Garmin
Kategoria: nawigator
Model: Nüvi 260

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Garmin Nüvi 260, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje nawigator Garmin

Garmin

Garmin GPSMAP 86s Instrukcja

12 Października 2024
Garmin

Garmin Dash Cam X210 Instrukcja

9 Października 2024
Garmin

Garmin Dash Cam X310 Instrukcja

9 Października 2024
Garmin

Garmin Dash Cam X110 Instrukcja

9 Października 2024
Garmin

Garmin dēzl OTR710 Instrukcja

5 Października 2024
Garmin

Garmin nüvi 255T Instrukcja

29 Września 2024
Garmin

Garmin Edge 840 Instrukcja

24 Września 2024
Garmin

Garmin zūmo XT2 Instrukcja

18 Września 2024

Instrukcje nawigator

Najnowsze instrukcje dla nawigator